[PATCH v2 3/6] arm64: dts: exynos7870: add DSI support

[Kaustabh Chakraborty]

On 2025-08-13 07:56, Krzysztof Kozlowski wrote:
> On 26/06/2025 22:13, Kaustabh Chakraborty wrote:
>>  			reboot-mode {
>>  				compatible = "syscon-reboot-mode";
>>  				offset = <0x080c>;
>> @@ -674,6 +682,83 @@ cmu_isp: clock-controller at 144d0000 {
>>  				 <&cmu_mif CLK_GOUT_MIF_CMU_ISP_VRA>;
>>  		};
>> 
>> +		syscon_cam0: syscon at 144f1040 {
>> +			compatible = "samsung,exynos7870-cam0-sysreg", "syscon";
>> +			reg = <0x144f1040 0x04>;
>> +		};
>> +
>> +		dsi: dsi at 14800000 {
>> +			compatible = "samsung,exynos7870-mipi-dsi";
>> +			reg = <0x14800000 0x100>;
>> +			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +			clock-names = "bus", "pll", "byte", "esc";
>> +			clocks = <&cmu_dispaud CLK_GOUT_DISPAUD_BUS_DISP>,
>> +				 <&cmu_dispaud CLK_GOUT_DISPAUD_APB_DISP>,
>> +				 <&cmu_dispaud CLK_GOUT_DISPAUD_MUX_MIPIPHY_TXBYTECLKHS_USER>,
>> +				 <&cmu_dispaud CLK_GOUT_DISPAUD_MUX_MIPIPHY_RXCLKESC0_USER>;
> 
> First clocks, then clock-names, please. Same for phys here and in all
> other place.

x-names followed by x approach is followed by the entire dts.
I will apply your suggestion in the next rev, and will also send a
separate patch for the same in all other places.

> 
>> +
>> +			phy-names = "dsim";
>> +			phys = <&mipi_phy 1>;
>> +
>> +			status = "disabled";
>> +
>> +			ports {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				port at 0 {
>> +					reg = <0>;
>> +
>> +					dsi_to_decon: endpoint {
>> +						remote-endpoint = <&decon_to_dsi>;
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		decon: decon at 14830000 {
> 
> node name: display-controller@

This was preemptively changed, thanks.

> 
>> +			compatible = "samsung,exynos7870-decon";
>> +			reg = <0x14830000 0x8000>;
>> +			interrupt-names = "fifo", "vsync", "lcd_sys";
>> +			interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +			clock-names = "pclk_decon0", "aclk_decon0",
>> +				      "decon0_eclk", "decon0_vclk";
>> +			clocks = <&cmu_dispaud CLK_GOUT_DISPAUD_MUX_PLL>,
>> +				 <&cmu_dispaud CLK_GOUT_DISPAUD_MUX_BUS_USER>,
>> +				 <&cmu_dispaud CLK_GOUT_DISPAUD_MUX_DECON_ECLK>,
>> +				 <&cmu_dispaud CLK_GOUT_DISPAUD_MUX_DECON_VCLK>;
>> +
>> +			iommus = <&sysmmu_decon>;
>> +
>> +			status = "disabled";
>> +
>> +			ports {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				port at 0 {
>> +					reg = <0>;
>> +					decon_to_dsi: endpoint {
>> +						remote-endpoint = <&dsi_to_decon>;
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		sysmmu_decon: sysmmu at 14860000 {
> 
> iommu@

Also preemptively changed.

> 
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x14860000 0x1000>;
>> +			interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
>> +			#iommu-cells = <0>;
>> +
>> +			clock-names = "sysmmu";
>> +			clocks = <&cmu_dispaud CLK_GOUT_DISPAUD_MUX_BUS_USER>;
>> +		};
> 
> 
> 
> Best regards,
> Krzysztof