[PATCH] arm64: dts: ti: k3-am62a7-sk: Describe the SPI NAND

[Kumar, Udit]

Thanks for patch Miquel

On 4/1/2025 7:28 PM, Miquel Raynal wrote:
> Describe the octal SPI NAND available on the low-power starter kit.
>
> The pinctrl configuration comes from TI fork.
>
> With the current mainline tree, we currently get the following
> performances:
>
> eraseblock write speed is 7507 KiB/s
> eraseblock read speed is 15802 KiB/s
> page write speed is 7551 KiB/s
> page read speed is 15609 KiB/s
> 2 page write speed is 7551 KiB/s
> 2 page read speed is 15609 KiB/s
> erase speed is 284444 KiB/s
> 2x multi-block erase speed is 512000 KiB/s
>
> Signed-off-by: Miquel Raynal <miquel.raynal at bootlin.com>
> ---
>   arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 40 +++++++++++++++++++++++++
>   1 file changed, 40 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index a6f0d87a50d8..6cc950f6dbe3 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -737,3 +737,43 @@ dpi1_out: endpoint {
>   		};
>   	};
>   };
> +
> +&fss {
> +	status = "okay";
> +};
> +
> +&ospi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ospi0_pins_default>;
> +
> +	flash at 0 {
> +		compatible = "spi-nand";

Since this is boot flash, so please add booth-all property as well


> +		reg = <0>;
> +		spi-tx-bus-width = <8>;
> +		spi-rx-bus-width = <8>;
> +		spi-max-frequency = <25000000>;
> +		cdns,tshsl-ns = <60>;
> +		cdns,tsd2d-ns = <60>;
> +		cdns,tchsh-ns = <60>;
> +		cdns,tslch-ns = <60>;
> +		cdns,read-delay = <2>;

Since this flash is used as boot device, I suggest if you can add 
partitions of flash as well .

you can take reference from downstream version [0]

> +	};
> +};
> +
> +&main_pmx0 {
> +	ospi0_pins_default: ospi0-default-pins {

please add booth-all property as well


> +		pinctrl-single,pins = <
> +			AM62AX_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
> +			AM62AX_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
> +			AM62AX_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
> +			AM62AX_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
> +			AM62AX_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
> +			AM62AX_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
> +			AM62AX_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
> +			AM62AX_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
> +			AM62AX_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
> +			AM62AX_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
> +			AM62AX_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
> +		>;
> +	};
> +};

[0] 
https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts?h=ti-linux-6.12.y-cicd#n798