[PATCH 3/6] thermal/drivers/sun8i: Add support for A523 THS0/1 controllers
Daniel Lezcano
daniel.lezcano at linaro.org
Fri Apr 18 01:41:34 PDT 2025
On Fri, Apr 11, 2025 at 08:38:23AM +0800, Mikhail Kalashnikov wrote:
> From: Mikhail Kalashnikov <iuncuim at gmail.com>
>
> The A523 processor has two temperature controllers, THS0 and THS1.
> THS0 has only one temperature sensor, which is located in the DRAM.
>
> THS1 does have 3 sensors:
> ths1_0 - "big" cores
> ths1_1 - "little" cores
> ths1_2 - gpu
>
> The datasheet mentions a fourth sensor in the NPU, but lacks any registers
> for operation other than calibration registers. The vendor code reads the
> value from ths1_2, but uses separate calibration data, so we get two
> different values from real one.
>
> Signed-off-by: Mikhail Kalashnikov <iuncuim at gmail.com>
> ---
> drivers/thermal/sun8i_thermal.c | 134 ++++++++++++++++++++++++++++++++
> 1 file changed, 134 insertions(+)
>
> diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
> index dc4055c9c..919b05a96 100644
> --- a/drivers/thermal/sun8i_thermal.c
> +++ b/drivers/thermal/sun8i_thermal.c
> @@ -116,6 +116,15 @@ static int sun50i_h5_calc_temp(struct ths_device *tmdev,
> return -1590 * reg / 10 + 276000;
> }
>
> +static int sun55i_a523_calc_temp(struct ths_device *tmdev,
> + int id, int reg)
> +{
> + if (reg >= 0x7c8)
> + return tmdev->chip->scale * (tmdev->chip->offset - reg);
> + else
> + return 65 * (2825 - reg);
> +}
Please use macro instead of litterals
> +
> static int sun8i_ths_get_temp(struct thermal_zone_device *tz, int *temp)
> {
> struct tsensor *s = thermal_zone_device_priv(tz);
> @@ -208,6 +217,100 @@ static irqreturn_t sun8i_irq_thread(int irq, void *data)
> return IRQ_HANDLED;
> }
>
> +
> +/*
> + * The A523 nvmem calibration values. The ths1_3 is not used as it
> + * doesn't have its own sensor and doesn't have any internal switch.
> + * Instead, the value from the ths1_2 sensor is used, which gives the
> + * illusion of an independent sensor for NPU and GPU when using
> + * different calibration values.
> + *
> + * efuse layout 0x38-0x3F (caldata[0..3]):
> + * caldata[0] caldata[1] caldata[2] caldata[3]
> + * 0 16 24 32 36 48 60 64
> + * +---------------+---------------+---------------+---------------+
> + * | | | temp | ths1_0 | ths1_1 | +
> + * +---------------+---------------+---------------+---------------+
> + *
> + * efuse layout 0x40-0x43 (caldata[4..5]) - not in use
> + *
> + * efuse layout 0x44-0x4B (caldata[6..9]):
> + * caldata[6] caldata[7] caldata[8] caldata[9]
> + * 0 12 16 24 32 36 48 64
> + * +---------------+---------------+---------------+---------------+
> + * | ths1_2 | ths1_3 | ths0_0 | | +
> + * +---------------+---------------+---------------+---------------+
> + */
> +static int sun55i_a523_ths_calibrate(struct ths_device *tmdev,
> + u16 *caldata, int callen)
> +{
> + struct device *dev = tmdev->dev;
> + int i, ft_temp;
> +
> + if (!caldata[0])
> + return -EINVAL;
> +
> + ft_temp = (((caldata[2] << 8) | (caldata[1] >> 8)) & FT_TEMP_MASK) * 100;
> +
> + for (i = 0; i < tmdev->chip->sensor_num; i++) {
> + int sensor_reg, sensor_temp, cdata, offset;
> + /*
> + * Chips ths0 and ths1 have common parameters for value
> + * calibration. To separate them we can use the number of
> + * temperature sensors on each chip.
> + * For ths0 this value is 1.
> + */
> + if (tmdev->chip->sensor_num == 1) {
> + sensor_reg = ((caldata[7] >> 8) | (caldata[8] << 8)) & TEMP_CALIB_MASK;
> + } else {
> + switch (i) {
> + case 0:
> + sensor_reg = (caldata[2] >> 4) & TEMP_CALIB_MASK;
> + break;
> + case 1:
> + sensor_reg = caldata[3] & TEMP_CALIB_MASK;
> + break;
> + case 2:
> + sensor_reg = caldata[6] & TEMP_CALIB_MASK;
> + break;
> + default:
> + sensor_reg = 0;
> + break;
> + }
> + }
> +
> + sensor_temp = tmdev->chip->calc_temp(tmdev, i, sensor_reg);
> +
> + /*
> + * Calibration data is CALIBRATE_DEFAULT - (calculated
> + * temperature from sensor reading at factory temperature
> + * minus actual factory temperature) * X (scale from
> + * temperature to register values)
> + */
> + cdata = CALIBRATE_DEFAULT -
> + ((sensor_temp - ft_temp) / tmdev->chip->scale);
> +
> + if (cdata & ~TEMP_CALIB_MASK) {
> + /*
> + * Calibration value more than 12-bit, but calibration
> + * register is 12-bit. In this case, ths hardware can
> + * still work without calibration, although the data
> + * won't be so accurate.
> + */
> + dev_warn(dev, "sensor%d is not calibrated.\n", i);
> + continue;
> + }
> +
> + offset = (i % 2) * 16;
> + regmap_update_bits(tmdev->regmap,
> + SUN50I_H6_THS_TEMP_CALIB + (i / 2 * 4),
> + TEMP_CALIB_MASK << offset,
> + cdata << offset);
> + }
> +
> + return 0;
> +}
> +
> static int sun8i_h3_ths_calibrate(struct ths_device *tmdev,
> u16 *caldata, int callen)
> {
> @@ -721,6 +824,35 @@ static const struct ths_thermal_chip sun50i_h616_ths = {
> .calc_temp = sun8i_ths_calc_temp,
> };
>
> +/* The A523 has a shared reset line for both chips */
> +static const struct ths_thermal_chip sun55i_a523_ths0 = {
> + .sensor_num = 1,
> + .has_bus_clk_reset = true,
> + .has_gpadc_clk = true,
> + .ft_deviation = 5000,
> + .offset = 2736,
> + .scale = 74,
> + .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
> + .calibrate = sun55i_a523_ths_calibrate,
> + .init = sun50i_h6_thermal_init,
> + .irq_ack = sun50i_h6_irq_ack,
> + .calc_temp = sun55i_a523_calc_temp,
> +};
> +
> +static const struct ths_thermal_chip sun55i_a523_ths1 = {
> + .sensor_num = 3,
> + .has_bus_clk_reset = true,
> + .has_gpadc_clk = true,
> + .ft_deviation = 5000,
> + .offset = 2736,
> + .scale = 74,
> + .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
> + .calibrate = sun55i_a523_ths_calibrate,
> + .init = sun50i_h6_thermal_init,
> + .irq_ack = sun50i_h6_irq_ack,
> + .calc_temp = sun55i_a523_calc_temp,
> +};
> +
> static const struct of_device_id of_ths_match[] = {
> { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths },
> { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
> @@ -731,6 +863,8 @@ static const struct of_device_id of_ths_match[] = {
> { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
> { .compatible = "allwinner,sun20i-d1-ths", .data = &sun20i_d1_ths },
> { .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths },
> + { .compatible = "allwinner,sun55i-a523-ths0", .data = &sun55i_a523_ths0 },
> + { .compatible = "allwinner,sun55i-a523-ths1", .data = &sun55i_a523_ths1 },
> { /* sentinel */ },
> };
> MODULE_DEVICE_TABLE(of, of_ths_match);
> --
> 2.49.0
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
More information about the linux-arm-kernel
mailing list