[PATCH v2 2/5] arm64: dts: ti: k3-am6*: Add boot phase flag to support MMC boot

[Judith Mendez]

The bootph-all flag was introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across
different boot phases.

For eMMC and SD boot modes, voltage regulator nodes, io-expander
nodes, gpio nodes, and MMC nodes need to be present in all boot
stages, so add missing bootph-all phase flag to these nodes to
support SD boot and eMMC boot.

Signed-off-by: Judith Mendez <jm at ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts | 12 ++++++++++++
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts  |  2 ++
 2 files changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
index 8e9fc00a6b3c7..aafdb90c0eb70 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
@@ -69,6 +69,7 @@ vddshv_sdio: regulator-4 {
 		gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
 		states = <1800000 0x0>,
 			 <3300000 0x1>;
+		bootph-all;
 	};
 };
 
@@ -77,12 +78,14 @@ vddshv_sdio_pins_default: vddshv-sdio-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (M19) GPMC0_CLK.GPIO0_31 */
 		>;
+		bootph-all;
 	};
 
 	main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (C13) UART0_RTSn.GPIO1_23 */
 		>;
+		bootph-all;
 	};
 
 	pmic_irq_pins_default: pmic-irq-default-pins {
@@ -118,6 +121,7 @@ exp1: gpio at 22 {
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+		bootph-all;
 	};
 
 	exp2: gpio at 23 {
@@ -229,6 +233,14 @@ &tlv320aic3106 {
 	DVDD-supply = <&buck2_reg>;
 };
 
+&main_gpio0 {
+	bootph-all;
+};
+
+&main_gpio1 {
+	bootph-all;
+};
+
 &gpmc0 {
 	ranges = <0 0 0x00 0x51000000 0x01000000>; /* CS0 space. Min partition = 16MB */
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 1c9d95696c839..7de4a9f139ad4 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -313,6 +313,7 @@ AM62AX_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */
 			AM62AX_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */
 			AM62AX_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
 		>;
+		bootph-all;
 	};
 
 	main_mmc1_pins_default: main-mmc1-default-pins {
@@ -615,6 +616,7 @@ &sdhci0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc0_pins_default>;
 	disable-wp;
+	bootph-all;
 };
 
 &sdhci1 {
-- 
2.49.0