[net-next v5 5/6] ARM: mxs_defconfig: Update mxs_defconfig to 6.15-rc1

[Stefan Wahren]

Hi Lukasz,

Am 14.04.25 um 16:01 schrieb Lukasz Majewski:
> This file is the updated version of mxs_defconfig for the v6.15-rc1
> linux-next.
thanks for sending this as a separate patch. Unfortunately it's not that 
simple by replacing the existing mxs_defconfig. We need to double-check 
all changes to settings, which was enabled before. This should also 
include a short note for every setting in the commit log, otherwise 
every reviewer has to do this job. I'll help you here by adding comments ...
>
> Signed-off-by: Lukasz Majewski <lukma at denx.de>
> ---
>
> Changes for v5:
> - New patch
> ---
>   arch/arm/configs/mxs_defconfig | 11 -----------
>   1 file changed, 11 deletions(-)
>
> diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
> index c76d66135abb..91723fdd3c04 100644
> --- a/arch/arm/configs/mxs_defconfig
> +++ b/arch/arm/configs/mxs_defconfig
> @@ -32,9 +32,6 @@ CONFIG_INET=y
>   CONFIG_IP_PNP=y
>   CONFIG_IP_PNP_DHCP=y
>   CONFIG_SYN_COOKIES=y
> -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
> -# CONFIG_INET_XFRM_MODE_TUNNEL is not set
> -# CONFIG_INET_XFRM_MODE_BEET is not set
>   # CONFIG_INET_DIAG is not set
>   # CONFIG_IPV6 is not set
>   CONFIG_CAN=m
> @@ -45,7 +42,6 @@ CONFIG_MTD=y
>   CONFIG_MTD_CMDLINE_PARTS=y
>   CONFIG_MTD_BLOCK=y
>   CONFIG_MTD_DATAFLASH=y
> -CONFIG_MTD_M25P80=y
This is safe because it has been replaced MTD_SPI_NOR, which is still 
enabled.
>   CONFIG_MTD_SST25L=y
>   CONFIG_MTD_RAW_NAND=y
>   CONFIG_MTD_NAND_GPMI_NAND=y
> @@ -60,7 +56,6 @@ CONFIG_ENC28J60=y
>   CONFIG_ICPLUS_PHY=y
>   CONFIG_MICREL_PHY=y
>   CONFIG_REALTEK_PHY=y
> -CONFIG_SMSC_PHY=y
This is okay, because it's enabled implicit by USB_NET_SMSC95XX.
>   CONFIG_CAN_FLEXCAN=m
>   CONFIG_USB_USBNET=y
>   CONFIG_USB_NET_SMSC95XX=y
> @@ -77,13 +72,11 @@ CONFIG_SERIAL_AMBA_PL011=y
>   CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
>   CONFIG_SERIAL_MXS_AUART=y
>   # CONFIG_HW_RANDOM is not set
> -# CONFIG_I2C_COMPAT is not set
>   CONFIG_I2C_CHARDEV=y
>   CONFIG_I2C_MXS=y
>   CONFIG_SPI=y
>   CONFIG_SPI_GPIO=m
>   CONFIG_SPI_MXS=y
> -CONFIG_GPIO_SYSFS=y
This also okay, because it has been deprecated by moving to EXPERT and 
its replacement GPIO_CDEV is enabled by default.
>   # CONFIG_HWMON is not set
>   CONFIG_WATCHDOG=y
>   CONFIG_STMP3XXX_RTC_WATCHDOG=y
> @@ -138,10 +131,6 @@ CONFIG_PWM_MXS=y
>   CONFIG_NVMEM_MXS_OCOTP=y
>   CONFIG_EXT4_FS=y
>   # CONFIG_DNOTIFY is not set
> -CONFIG_NETFS_SUPPORT=m
> -CONFIG_FSCACHE=y
> -CONFIG_FSCACHE_STATS=y
> -CONFIG_CACHEFILES=m
This is unintended, even it's not your fault Lukasz. NETFS_SUPPORT isn't 
user select-able anymore, so it's dropped. AFAIU this comes from NFS 
support, so i think we need to enable CONFIG_NFS_FSCACHE here. Otherwise 
this caching feature get lost. Since this is a bugfix, this should be 
separate patch before the syncronization.

@Shawn @Fabio what's your opinion?
>   CONFIG_VFAT_FS=y
>   CONFIG_TMPFS=y
>   CONFIG_TMPFS_POSIX_ACL=y