[PATCH 4/5] arm64: dts: rockchip: Enable all 3 USBs on Turing RK1

[Sam Edwards]

The Turing RK1 contains 3 different USBs:
- USB0: USB 2.0, OTG
- USB1: USB 3.0, host
- USB2: USB 2.0, host

This patch activates the necessary DT nodes to enable all 3 buses.

Future work will be needed on USB0: it is not USB 3.0, but Linux creates
an unused USB 3.0 root hub and the controller also requires that USBDP0
be powered up. However, it is possible to remove this dependency. By
either patching the xHCI driver to ignore the enumerated USB 3.0 port or
setting usb3otg0_host_num_u3_port=0 in the GRF to stop the controller
from enumerating a USB 3.0 port in the first place, neither Linux nor
the controller will expect USB 3.0 capability, and USBDP0 can then
safely be removed from the `phys` property.

Signed-off-by: Sam Edwards <CFSworks at gmail.com>
---
 .../boot/dts/rockchip/rk3588-turing-rk1.dtsi  | 64 +++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-turing-rk1.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-turing-rk1.dtsi
index f6a12fe12d45..6036c4fe6727 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-turing-rk1.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588-turing-rk1.dtsi
@@ -666,3 +666,67 @@ &uart9 {
 	pinctrl-0 = <&uart9m0_xfer>;
 	status = "okay";
 };
+
+/* USB 0: USB 2.0 only, OTG-capable */
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	status = "okay";
+};
+
+&usbdp_phy0 {
+	/*
+	 * TODO: On the RK1, USBDP0 drives the DisplayPort pins, and is not
+	 * involved in this USB2-only bus.  However, if the USB3 port is
+	 * enabled in the xHCI below, the controller will expect this PHY to be
+	 * powered up and holding RX_STATUS idle, or else it will generate an
+	 * endless stream of CSC events whenever a device is plugged in.  Until
+	 * there is a way to communicate to usb_host0_xhci that it doesn't have
+	 * a USB3 port, we have no choice but to power up USBDP0.
+	 */
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	extcon = <&u2phy0>;
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+/* USB 1: USB 3.0, host only */
+&u2phy1 {
+	status = "okay";
+};
+
+&u2phy1_otg {
+	status = "okay";
+};
+
+&usbdp_phy1 {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	extcon = <&u2phy1>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* USB 2: USB 2.0, host only */
+&u2phy2 {
+	status = "okay";
+};
+
+&u2phy2_host {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
-- 
2.44.2