[PATCH RFC/RFT 1/2] arm64: dts: ti: k3-j784s4-evm: Mark tps659413 and children as bootph-all

Kumar, Udit u-kumar1 at ti.com
Fri Sep 6 22:34:50 PDT 2024


Thanks for your patch Andrew


On 9/7/2024 2:51 AM, Andrew Halaney wrote:
> In order for the MCU domain to access this PMIC and its children in
> u-boot SPL, the nodes need to be marked appropriately otherwise they
> are not seen by SPL.
>
> This is necessary if the MCU domain is to program the TPS6594 MCU ESM
> state machine, which is required to wire up the watchdog in a manner
> that will reset the board.
>
> Signed-off-by: Andrew Halaney <ahalaney at redhat.com>
> ---
>   arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 11 +++++++++++
>   1 file changed, 11 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> index 6695ebbcb4d0..044a428136df 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -642,6 +642,7 @@ eeprom at 50 {
>   	};
>   
>   	tps659413: pmic at 48 {
> +		bootph-all;
>   		compatible = "ti,tps6594-q1";
>   		reg = <0x48>;
>   		system-power-controller;
> @@ -662,7 +663,10 @@ tps659413: pmic at 48 {
>   		ldo4-supply = <&vsys_3v3>;
>   
>   		regulators {
> +			bootph-all;
> +
>   			bucka12: buck12 {
> +				bootph-all;


Add bootph in on regulator node should be enough,

As I see SPL/u-boot does not need all nodes.


FYI,

Similar series in review

https://lore.kernel.org/all/20240814-b4-upstream-bootph-all-v4-0-f2b462000f25@ti.com/ 


>   				regulator-name = "vdd_ddr_1v1";
>   				regulator-min-microvolt = <1100000>;
>   				regulator-max-microvolt = <1100000>;
> @@ -671,6 +675,7 @@ bucka12: buck12 {
>   			};
>   
>   			bucka3: buck3 {
> +				bootph-all;
>   				regulator-name = "vdd_ram_0v85";
>   				regulator-min-microvolt = <850000>;
>   				regulator-max-microvolt = <850000>;
> @@ -679,6 +684,7 @@ bucka3: buck3 {
>   			};
>   
>   			bucka4: buck4 {
> +				bootph-all;
>   				regulator-name = "vdd_io_1v8";
>   				regulator-min-microvolt = <1800000>;
>   				regulator-max-microvolt = <1800000>;
> @@ -687,6 +693,7 @@ bucka4: buck4 {
>   			};
>   
>   			bucka5: buck5 {
> +				bootph-all;
>   				regulator-name = "vdd_mcu_0v85";
>   				regulator-min-microvolt = <850000>;
>   				regulator-max-microvolt = <850000>;
> @@ -695,6 +702,7 @@ bucka5: buck5 {
>   			};
>   
>   			ldoa1: ldo1 {
> +				bootph-all;
>   				regulator-name = "vdd_mcuio_1v8";
>   				regulator-min-microvolt = <1800000>;
>   				regulator-max-microvolt = <1800000>;
> @@ -703,6 +711,7 @@ ldoa1: ldo1 {
>   			};
>   
>   			ldoa2: ldo2 {
> +				bootph-all;
>   				regulator-name = "vdd_mcuio_3v3";
>   				regulator-min-microvolt = <3300000>;
>   				regulator-max-microvolt = <3300000>;
> @@ -711,6 +720,7 @@ ldoa2: ldo2 {
>   			};
>   
>   			ldoa3: ldo3 {
> +				bootph-all;
>   				regulator-name = "vds_dll_0v8";
>   				regulator-min-microvolt = <800000>;
>   				regulator-max-microvolt = <800000>;
> @@ -719,6 +729,7 @@ ldoa3: ldo3 {
>   			};
>   
>   			ldoa4: ldo4 {
> +				bootph-all;
>   				regulator-name = "vda_mcu_1v8";
>   				regulator-min-microvolt = <1800000>;
>   				regulator-max-microvolt = <1800000>;
>



More information about the linux-arm-kernel mailing list