[PATCH net-next v9 3/7] net: stmmac: refactor FPE verification process

[Vladimir Oltean]

On Fri, Sep 06, 2024 at 12:55:58PM +0800, Furong Xu wrote:
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> @@ -969,17 +969,30 @@ static void stmmac_mac_config(struct phylink_config *config, unsigned int mode,
>  static void stmmac_fpe_link_state_handle(struct stmmac_priv *priv, bool is_up)
>  {
>  	struct stmmac_fpe_cfg *fpe_cfg = &priv->fpe_cfg;
> -	enum stmmac_fpe_state *lo_state = &fpe_cfg->lo_fpe_state;
> -	enum stmmac_fpe_state *lp_state = &fpe_cfg->lp_fpe_state;
> -	bool *hs_enable = &fpe_cfg->hs_enable;
> +	unsigned long flags;
>  
> -	if (is_up && *hs_enable) {
> -		stmmac_fpe_send_mpacket(priv, priv->ioaddr, fpe_cfg,
> -					MPACKET_VERIFY);
> +	timer_shutdown_sync(&fpe_cfg->verify_timer);
>  }
>  
>  static void stmmac_mac_link_down(struct phylink_config *config,
> @@ -4091,10 +4068,10 @@ static int stmmac_release(struct net_device *dev)
>  
>  	stmmac_release_ptp(priv);
>  
> -	pm_runtime_put(priv->device);
> -
>  	if (priv->dma_cap.fpesel)
> -		stmmac_fpe_stop_wq(priv);
> +		timer_shutdown_sync(&priv->fpe_cfg.verify_timer);
> +
> +	pm_runtime_put(priv->device);
>  
>  	return 0;
>  }
> @@ -7372,53 +7334,88 @@ int stmmac_reinit_ringparam(struct net_device *dev, u32 rx_size, u32 tx_size)
> +static void stmmac_fpe_verify_timer_arm(struct stmmac_fpe_cfg *fpe_cfg)
> +{
> +	if (fpe_cfg->pmac_enabled && fpe_cfg->tx_enabled &&
> +	    fpe_cfg->verify_enabled &&
> +	    fpe_cfg->status != ETHTOOL_MM_VERIFY_STATUS_FAILED &&
> +	    fpe_cfg->status != ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED) {
> +		timer_setup(&fpe_cfg->verify_timer, stmmac_fpe_verify_timer, 0);
> +		mod_timer(&fpe_cfg->verify_timer, jiffies);
> +	}
> +}
> @@ -7875,15 +7874,8 @@ int stmmac_suspend(struct device *dev)
>  	}
>  	rtnl_unlock();
>  
> -	if (priv->dma_cap.fpesel) {
> -		/* Disable FPE */
> -		stmmac_fpe_configure(priv, priv->ioaddr,
> -				     &priv->fpe_cfg,
> -				     priv->plat->tx_queues_to_use,
> -				     priv->plat->rx_queues_to_use, false);
> -
> -		stmmac_fpe_stop_wq(priv);
> -	}
> +	if (priv->dma_cap.fpesel)
> +		timer_shutdown_sync(&priv->fpe_cfg.verify_timer);
>  
>  	priv->speed = SPEED_UNKNOWN;
>  	return 0;

Calling timer_setup() after timer_shutdown_sync() is a bit unconventional,
but I don't see why it shouldn't work.

Reviewed-by: Vladimir Oltean <olteanv at gmail.com>