[PATCH net-next v7 3/7] net: stmmac: refactor FPE verification process
Furong Xu
0x1207 at gmail.com
Wed Sep 4 02:21:18 PDT 2024
Drop driver defined stmmac_fpe_state, and switch to common
ethtool_mm_verify_status for local TX verification status.
Local side and remote side verification processes are completely
independent. There is no reason at all to keep a local state and
a remote state.
Add a spinlock to avoid races among ISR, timer, link update
and register configuration.
This patch is based on Vladimir Oltean's proposal.
Vladimir Oltean says:
====================
In the INITIAL state, the timer sends MPACKET_VERIFY. Eventually the
stmmac_fpe_event_status() IRQ fires and advances the state to VERIFYING,
then rearms the timer after verify_time ms. If a subsequent IRQ comes in
and modifies the state to SUCCEEDED after getting MPACKET_RESPONSE, the
timer sees this. It must enable the EFPE bit now. Otherwise, it
decrements the verify_limit counter and tries again. Eventually it
moves the status to FAILED, from which the IRQ cannot move it anywhere
else, except for another stmmac_fpe_apply() call.
====================
Co-developed-by: Vladimir Oltean <vladimir.oltean at nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean at nxp.com>
Signed-off-by: Furong Xu <0x1207 at gmail.com>
---
.../net/ethernet/stmicro/stmmac/dwmac4_core.c | 4 -
drivers/net/ethernet/stmicro/stmmac/dwmac5.c | 19 +-
drivers/net/ethernet/stmicro/stmmac/dwmac5.h | 2 +-
.../ethernet/stmicro/stmmac/dwxgmac2_core.c | 9 +-
drivers/net/ethernet/stmicro/stmmac/hwif.h | 2 +-
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 31 +--
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 258 +++++++++---------
.../net/ethernet/stmicro/stmmac/stmmac_tc.c | 8 +-
8 files changed, 164 insertions(+), 169 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
index 31c387cc5f26..7947b1212a2d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
@@ -58,10 +58,6 @@ static void dwmac4_core_init(struct mac_device_info *hw,
if (hw->pcs)
value |= GMAC_PCS_IRQ_DEFAULT;
- /* Enable FPE interrupt */
- if ((GMAC_HW_FEAT_FPESEL & readl(ioaddr + GMAC_HW_FEATURE3)) >> 26)
- value |= GMAC_INT_FPE_EN;
-
writel(value, ioaddr + GMAC_INT_EN);
if (GMAC_INT_DEFAULT_ENABLE & GMAC_INT_TSIE)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac5.c b/drivers/net/ethernet/stmicro/stmmac/dwmac5.c
index e02cebc3f1b7..850cfc4df6eb 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac5.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac5.c
@@ -575,11 +575,11 @@ int dwmac5_flex_pps_config(void __iomem *ioaddr, int index,
void dwmac5_fpe_configure(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
u32 num_txq, u32 num_rxq,
- bool enable)
+ bool tx_enable, bool pmac_enable)
{
u32 value;
- if (enable) {
+ if (tx_enable) {
cfg->fpe_csr = EFPE;
value = readl(ioaddr + GMAC_RXQ_CTRL1);
value &= ~GMAC_RXQCTRL_FPRQ;
@@ -589,6 +589,21 @@ void dwmac5_fpe_configure(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
cfg->fpe_csr = 0;
}
writel(cfg->fpe_csr, ioaddr + MAC_FPE_CTRL_STS);
+
+ value = readl(ioaddr + GMAC_INT_EN);
+
+ if (pmac_enable) {
+ if (!(value & GMAC_INT_FPE_EN)) {
+ /* Dummy read to clear any pending masked interrupts */
+ readl(ioaddr + MAC_FPE_CTRL_STS);
+
+ value |= GMAC_INT_FPE_EN;
+ }
+ } else {
+ value &= ~GMAC_INT_FPE_EN;
+ }
+
+ writel(value, ioaddr + GMAC_INT_EN);
}
int dwmac5_fpe_irq_status(void __iomem *ioaddr, struct net_device *dev)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac5.h b/drivers/net/ethernet/stmicro/stmmac/dwmac5.h
index bf33a51d229e..c3031c1357d0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac5.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac5.h
@@ -104,7 +104,7 @@ int dwmac5_flex_pps_config(void __iomem *ioaddr, int index,
u32 sub_second_inc, u32 systime_flags);
void dwmac5_fpe_configure(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
u32 num_txq, u32 num_rxq,
- bool enable);
+ bool tx_enable, bool pmac_enable);
void dwmac5_fpe_send_mpacket(void __iomem *ioaddr,
struct stmmac_fpe_cfg *cfg,
enum stmmac_mpacket_type type);
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c
index cbf2dd976ab1..f519d43738b0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c
@@ -1504,13 +1504,14 @@ static void dwxgmac2_set_arp_offload(struct mac_device_info *hw, bool en,
writel(value, ioaddr + XGMAC_RX_CONFIG);
}
-static void dwxgmac3_fpe_configure(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
- u32 num_txq,
- u32 num_rxq, bool enable)
+static void dwxgmac3_fpe_configure(void __iomem *ioaddr,
+ struct stmmac_fpe_cfg *cfg,
+ u32 num_txq, u32 num_rxq,
+ bool tx_enable, bool pmac_enable)
{
u32 value;
- if (!enable) {
+ if (!tx_enable) {
value = readl(ioaddr + XGMAC_FPE_CTRL_STS);
value &= ~XGMAC_EFPE;
diff --git a/drivers/net/ethernet/stmicro/stmmac/hwif.h b/drivers/net/ethernet/stmicro/stmmac/hwif.h
index 68574798c03f..4942fc398ea6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/hwif.h
+++ b/drivers/net/ethernet/stmicro/stmmac/hwif.h
@@ -421,7 +421,7 @@ struct stmmac_ops {
void (*set_arp_offload)(struct mac_device_info *hw, bool en, u32 addr);
void (*fpe_configure)(void __iomem *ioaddr, struct stmmac_fpe_cfg *cfg,
u32 num_txq, u32 num_rxq,
- bool enable);
+ bool tx_enable, bool pmac_enable);
void (*fpe_send_mpacket)(void __iomem *ioaddr,
struct stmmac_fpe_cfg *cfg,
enum stmmac_mpacket_type type);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 3ad182ef8e97..535d1b0c4bbf 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -146,31 +146,25 @@ struct stmmac_channel {
u32 index;
};
-/* FPE link state */
-enum stmmac_fpe_state {
- FPE_STATE_OFF = 0,
- FPE_STATE_CAPABLE = 1,
- FPE_STATE_ENTERING_ON = 2,
- FPE_STATE_ON = 3,
-};
-
/* FPE link-partner hand-shaking mPacket type */
enum stmmac_mpacket_type {
MPACKET_VERIFY = 0,
MPACKET_RESPONSE = 1,
};
-enum stmmac_fpe_task_state_t {
- __FPE_REMOVING,
- __FPE_TASK_SCHED,
-};
+#define STMMAC_FPE_MM_MAX_VERIFY_RETRIES 3
+#define STMMAC_FPE_MM_MAX_VERIFY_TIME_MS 128
struct stmmac_fpe_cfg {
- bool enable; /* FPE enable */
- bool hs_enable; /* FPE handshake enable */
- enum stmmac_fpe_state lp_fpe_state; /* Link Partner FPE state */
- enum stmmac_fpe_state lo_fpe_state; /* Local station FPE state */
+ /* Serialize access to MAC Merge state between ethtool requests
+ * and link state updates.
+ */
+ spinlock_t lock;
+
u32 fpe_csr; /* MAC_FPE_CTRL_STS reg cache */
+ struct timer_list verify_timer;
+ struct ethtool_mm_state state;
+ int verify_retries;
};
struct stmmac_tc_entry {
@@ -367,10 +361,6 @@ struct stmmac_priv {
struct work_struct service_task;
/* Frame Preemption feature (FPE) */
- unsigned long fpe_task_state;
- struct workqueue_struct *fpe_wq;
- struct work_struct fpe_task;
- char wq_name[IFNAMSIZ + 4];
struct stmmac_fpe_cfg fpe_cfg;
/* TC Handling */
@@ -425,6 +415,7 @@ bool stmmac_eee_init(struct stmmac_priv *priv);
int stmmac_reinit_queues(struct net_device *dev, u32 rx_cnt, u32 tx_cnt);
int stmmac_reinit_ringparam(struct net_device *dev, u32 rx_size, u32 tx_size);
int stmmac_bus_clks_config(struct stmmac_priv *priv, bool enabled);
+void stmmac_fpe_apply(struct stmmac_priv *priv);
static inline bool stmmac_xdp_is_enabled(struct stmmac_priv *priv)
{
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 3072ad33b105..e2f933353f40 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -969,17 +969,30 @@ static void stmmac_mac_config(struct phylink_config *config, unsigned int mode,
static void stmmac_fpe_link_state_handle(struct stmmac_priv *priv, bool is_up)
{
struct stmmac_fpe_cfg *fpe_cfg = &priv->fpe_cfg;
- enum stmmac_fpe_state *lo_state = &fpe_cfg->lo_fpe_state;
- enum stmmac_fpe_state *lp_state = &fpe_cfg->lp_fpe_state;
- bool *hs_enable = &fpe_cfg->hs_enable;
+ unsigned long flags;
- if (is_up && *hs_enable) {
- stmmac_fpe_send_mpacket(priv, priv->ioaddr, fpe_cfg,
- MPACKET_VERIFY);
+ del_timer_sync(&fpe_cfg->verify_timer);
+
+ spin_lock_irqsave(&fpe_cfg->lock, flags);
+
+ if (is_up && fpe_cfg->state.pmac_enabled) {
+ /* VERIFY process requires pmac enabled when NIC comes up */
+ stmmac_fpe_configure(priv, priv->ioaddr, fpe_cfg,
+ priv->plat->tx_queues_to_use,
+ priv->plat->rx_queues_to_use,
+ false, true);
+
+ /* New link => maybe new partner => new verification process */
+ stmmac_fpe_apply(priv);
} else {
- *lo_state = FPE_STATE_OFF;
- *lp_state = FPE_STATE_OFF;
+ /* No link => turn off EFPE */
+ stmmac_fpe_configure(priv, priv->ioaddr, fpe_cfg,
+ priv->plat->tx_queues_to_use,
+ priv->plat->rx_queues_to_use,
+ false, false);
}
+
+ spin_unlock_irqrestore(&fpe_cfg->lock, flags);
}
static void stmmac_mac_link_down(struct phylink_config *config,
@@ -3358,27 +3371,6 @@ static void stmmac_safety_feat_configuration(struct stmmac_priv *priv)
}
}
-static int stmmac_fpe_start_wq(struct stmmac_priv *priv)
-{
- char *name;
-
- clear_bit(__FPE_TASK_SCHED, &priv->fpe_task_state);
- clear_bit(__FPE_REMOVING, &priv->fpe_task_state);
-
- name = priv->wq_name;
- sprintf(name, "%s-fpe", priv->dev->name);
-
- priv->fpe_wq = create_singlethread_workqueue(name);
- if (!priv->fpe_wq) {
- netdev_err(priv->dev, "%s: Failed to create workqueue\n", name);
-
- return -ENOMEM;
- }
- netdev_info(priv->dev, "FPE workqueue start");
-
- return 0;
-}
-
/**
* stmmac_hw_setup - setup mac in a usable state.
* @dev : pointer to the device structure.
@@ -3533,9 +3525,6 @@ static int stmmac_hw_setup(struct net_device *dev, bool ptp_register)
stmmac_set_hw_vlan_mode(priv, priv->hw);
- if (priv->dma_cap.fpesel)
- stmmac_fpe_start_wq(priv);
-
return 0;
}
@@ -4032,18 +4021,6 @@ static int stmmac_open(struct net_device *dev)
return ret;
}
-static void stmmac_fpe_stop_wq(struct stmmac_priv *priv)
-{
- set_bit(__FPE_REMOVING, &priv->fpe_task_state);
-
- if (priv->fpe_wq) {
- destroy_workqueue(priv->fpe_wq);
- priv->fpe_wq = NULL;
- }
-
- netdev_info(priv->dev, "FPE workqueue stop");
-}
-
/**
* stmmac_release - close entry point of the driver
* @dev : device pointer.
@@ -4091,10 +4068,10 @@ static int stmmac_release(struct net_device *dev)
stmmac_release_ptp(priv);
- pm_runtime_put(priv->device);
-
if (priv->dma_cap.fpesel)
- stmmac_fpe_stop_wq(priv);
+ del_timer_sync(&priv->fpe_cfg.verify_timer);
+
+ pm_runtime_put(priv->device);
return 0;
}
@@ -5978,45 +5955,31 @@ static int stmmac_set_features(struct net_device *netdev,
static void stmmac_fpe_event_status(struct stmmac_priv *priv, int status)
{
+ struct ethtool_mm_state *state = &priv->fpe_cfg.state;
struct stmmac_fpe_cfg *fpe_cfg = &priv->fpe_cfg;
- enum stmmac_fpe_state *lo_state = &fpe_cfg->lo_fpe_state;
- enum stmmac_fpe_state *lp_state = &fpe_cfg->lp_fpe_state;
- bool *hs_enable = &fpe_cfg->hs_enable;
- if (status == FPE_EVENT_UNKNOWN || !*hs_enable)
- return;
+ /* this is interrupt context, just spin_lock */
+ spin_lock(&fpe_cfg->lock);
- /* If LP has sent verify mPacket, LP is FPE capable */
- if ((status & FPE_EVENT_RVER) == FPE_EVENT_RVER) {
- if (*lp_state < FPE_STATE_CAPABLE)
- *lp_state = FPE_STATE_CAPABLE;
+ if (!state->pmac_enabled || status == FPE_EVENT_UNKNOWN)
+ goto unlock_out;
- /* If user has requested FPE enable, quickly response */
- if (*hs_enable)
- stmmac_fpe_send_mpacket(priv, priv->ioaddr,
- fpe_cfg,
- MPACKET_RESPONSE);
- }
+ /* LP has sent verify mPacket */
+ if ((status & FPE_EVENT_RVER) == FPE_EVENT_RVER)
+ stmmac_fpe_send_mpacket(priv, priv->ioaddr, fpe_cfg,
+ MPACKET_RESPONSE);
- /* If Local has sent verify mPacket, Local is FPE capable */
- if ((status & FPE_EVENT_TVER) == FPE_EVENT_TVER) {
- if (*lo_state < FPE_STATE_CAPABLE)
- *lo_state = FPE_STATE_CAPABLE;
- }
+ /* Local has sent verify mPacket */
+ if ((status & FPE_EVENT_TVER) == FPE_EVENT_TVER &&
+ state->verify_status != ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED)
+ state->verify_status = ETHTOOL_MM_VERIFY_STATUS_VERIFYING;
- /* If LP has sent response mPacket, LP is entering FPE ON */
+ /* LP has sent response mPacket */
if ((status & FPE_EVENT_RRSP) == FPE_EVENT_RRSP)
- *lp_state = FPE_STATE_ENTERING_ON;
-
- /* If Local has sent response mPacket, Local is entering FPE ON */
- if ((status & FPE_EVENT_TRSP) == FPE_EVENT_TRSP)
- *lo_state = FPE_STATE_ENTERING_ON;
+ state->verify_status = ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED;
- if (!test_bit(__FPE_REMOVING, &priv->fpe_task_state) &&
- !test_and_set_bit(__FPE_TASK_SCHED, &priv->fpe_task_state) &&
- priv->fpe_wq) {
- queue_work(priv->fpe_wq, &priv->fpe_task);
- }
+unlock_out:
+ spin_unlock(&fpe_cfg->lock);
}
static void stmmac_common_interrupt(struct stmmac_priv *priv)
@@ -7372,53 +7335,90 @@ int stmmac_reinit_ringparam(struct net_device *dev, u32 rx_size, u32 tx_size)
return ret;
}
-#define SEND_VERIFY_MPAKCET_FMT "Send Verify mPacket lo_state=%d lp_state=%d\n"
-static void stmmac_fpe_lp_task(struct work_struct *work)
+/**
+ * stmmac_fpe_verify_timer - Timer for MAC Merge verification
+ * @t: timer_list struct containing private info
+ *
+ * Verify the MAC Merge capability in the local TX direction, by
+ * transmitting Verify mPackets up to 3 times. Wait until link
+ * partner responds with a Response mPacket, otherwise fail.
+ */
+static void stmmac_fpe_verify_timer(struct timer_list *t)
{
- struct stmmac_priv *priv = container_of(work, struct stmmac_priv,
- fpe_task);
- struct stmmac_fpe_cfg *fpe_cfg = &priv->fpe_cfg;
- enum stmmac_fpe_state *lo_state = &fpe_cfg->lo_fpe_state;
- enum stmmac_fpe_state *lp_state = &fpe_cfg->lp_fpe_state;
- bool *hs_enable = &fpe_cfg->hs_enable;
- bool *enable = &fpe_cfg->enable;
- int retries = 20;
-
- while (retries-- > 0) {
- /* Bail out immediately if FPE handshake is OFF */
- if (*lo_state == FPE_STATE_OFF || !*hs_enable)
- break;
-
- if (*lo_state == FPE_STATE_ENTERING_ON &&
- *lp_state == FPE_STATE_ENTERING_ON) {
- stmmac_fpe_configure(priv, priv->ioaddr,
- fpe_cfg,
- priv->plat->tx_queues_to_use,
- priv->plat->rx_queues_to_use,
- *enable);
-
- netdev_info(priv->dev, "configured FPE\n");
+ struct stmmac_fpe_cfg *fpe_cfg = from_timer(fpe_cfg, t, verify_timer);
+ struct stmmac_priv *priv = container_of(fpe_cfg, struct stmmac_priv,
+ fpe_cfg);
+ struct ethtool_mm_state *state = &fpe_cfg->state;
+ unsigned long flags;
+ bool rearm = false;
- *lo_state = FPE_STATE_ON;
- *lp_state = FPE_STATE_ON;
- netdev_info(priv->dev, "!!! BOTH FPE stations ON\n");
- break;
- }
+ spin_lock_irqsave(&fpe_cfg->lock, flags);
- if ((*lo_state == FPE_STATE_CAPABLE ||
- *lo_state == FPE_STATE_ENTERING_ON) &&
- *lp_state != FPE_STATE_ON) {
- netdev_info(priv->dev, SEND_VERIFY_MPAKCET_FMT,
- *lo_state, *lp_state);
+ switch (state->verify_status) {
+ case ETHTOOL_MM_VERIFY_STATUS_INITIAL:
+ case ETHTOOL_MM_VERIFY_STATUS_VERIFYING:
+ if (fpe_cfg->verify_retries != 0) {
stmmac_fpe_send_mpacket(priv, priv->ioaddr,
- fpe_cfg,
- MPACKET_VERIFY);
+ fpe_cfg, MPACKET_VERIFY);
+ rearm = true;
+ } else {
+ state->verify_status = ETHTOOL_MM_VERIFY_STATUS_FAILED;
}
- /* Sleep then retry */
- msleep(500);
+
+ fpe_cfg->verify_retries--;
+ break;
+
+ case ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED:
+ stmmac_fpe_configure(priv, priv->ioaddr, fpe_cfg,
+ priv->plat->tx_queues_to_use,
+ priv->plat->rx_queues_to_use,
+ true, true);
+ break;
+
+ default:
+ break;
+ }
+
+ if (rearm) {
+ mod_timer(&fpe_cfg->verify_timer,
+ jiffies + msecs_to_jiffies(state->verify_time));
}
- clear_bit(__FPE_TASK_SCHED, &priv->fpe_task_state);
+ spin_unlock_irqrestore(&fpe_cfg->lock, flags);
+}
+
+static void stmmac_fpe_verify_timer_arm(struct stmmac_fpe_cfg *fpe_cfg)
+{
+ struct ethtool_mm_state *state = &fpe_cfg->state;
+
+ if (state->pmac_enabled && state->tx_enabled &&
+ state->verify_enabled &&
+ state->verify_status != ETHTOOL_MM_VERIFY_STATUS_FAILED &&
+ state->verify_status != ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED) {
+ /* give caller a chance to release the spinlock */
+ mod_timer(&fpe_cfg->verify_timer, jiffies + 1);
+ }
+}
+
+void stmmac_fpe_apply(struct stmmac_priv *priv)
+{
+ struct ethtool_mm_state *state = &priv->fpe_cfg.state;
+ struct stmmac_fpe_cfg *fpe_cfg = &priv->fpe_cfg;
+
+ /* If verification is disabled, configure FPE right away.
+ * Otherwise let the timer code do it.
+ */
+ if (!state->verify_enabled) {
+ stmmac_fpe_configure(priv, priv->ioaddr, fpe_cfg,
+ priv->plat->tx_queues_to_use,
+ priv->plat->rx_queues_to_use,
+ state->tx_enabled,
+ state->pmac_enabled);
+ } else {
+ state->verify_status = ETHTOOL_MM_VERIFY_STATUS_INITIAL;
+ fpe_cfg->verify_retries = STMMAC_FPE_MM_MAX_VERIFY_RETRIES;
+ stmmac_fpe_verify_timer_arm(fpe_cfg);
+ }
}
static int stmmac_xdp_rx_timestamp(const struct xdp_md *_ctx, u64 *timestamp)
@@ -7535,9 +7535,6 @@ int stmmac_dvr_probe(struct device *device,
INIT_WORK(&priv->service_task, stmmac_service_task);
- /* Initialize Link Partner FPE workqueue */
- INIT_WORK(&priv->fpe_task, stmmac_fpe_lp_task);
-
/* Override with kernel parameters if supplied XXX CRS XXX
* this needs to have multiple instances
*/
@@ -7702,6 +7699,14 @@ int stmmac_dvr_probe(struct device *device,
mutex_init(&priv->lock);
+ spin_lock_init(&priv->fpe_cfg.lock);
+ timer_setup(&priv->fpe_cfg.verify_timer, stmmac_fpe_verify_timer, 0);
+ priv->fpe_cfg.state.verify_time = STMMAC_FPE_MM_MAX_VERIFY_TIME_MS;
+ priv->fpe_cfg.state.max_verify_time = STMMAC_FPE_MM_MAX_VERIFY_TIME_MS;
+ priv->fpe_cfg.state.verify_status = ETHTOOL_MM_VERIFY_STATUS_DISABLED;
+ priv->fpe_cfg.state.rx_min_frag_size = ETH_ZLEN;
+ priv->fpe_cfg.verify_retries = STMMAC_FPE_MM_MAX_VERIFY_RETRIES;
+
/* If a specific clk_csr value is passed from the platform
* this means that the CSR Clock Range selection cannot be
* changed at run-time and it is fixed. Viceversa the driver'll try to
@@ -7875,15 +7880,8 @@ int stmmac_suspend(struct device *dev)
}
rtnl_unlock();
- if (priv->dma_cap.fpesel) {
- /* Disable FPE */
- stmmac_fpe_configure(priv, priv->ioaddr,
- &priv->fpe_cfg,
- priv->plat->tx_queues_to_use,
- priv->plat->rx_queues_to_use, false);
-
- stmmac_fpe_stop_wq(priv);
- }
+ if (priv->dma_cap.fpesel)
+ del_timer_sync(&priv->fpe_cfg.verify_timer);
priv->speed = SPEED_UNKNOWN;
return 0;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
index b0cc45331ff7..a58282d6458c 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
@@ -1063,11 +1063,6 @@ static int tc_taprio_configure(struct stmmac_priv *priv,
return -EOPNOTSUPP;
}
- /* Actual FPE register configuration will be done after FPE handshake
- * is success.
- */
- priv->fpe_cfg.enable = fpe;
-
ret = stmmac_est_configure(priv, priv, priv->est,
priv->plat->clk_ptp_rate);
mutex_unlock(&priv->est_lock);
@@ -1094,12 +1089,11 @@ static int tc_taprio_configure(struct stmmac_priv *priv,
mutex_unlock(&priv->est_lock);
}
- priv->fpe_cfg.enable = false;
stmmac_fpe_configure(priv, priv->ioaddr,
&priv->fpe_cfg,
priv->plat->tx_queues_to_use,
priv->plat->rx_queues_to_use,
- false);
+ false, false);
netdev_info(priv->dev, "disabled FPE\n");
return ret;
--
2.34.1
More information about the linux-arm-kernel
mailing list