[PATCH v6 4/4] PCI: qcom: Add RX margining settings for 16.0 GT/s

[Johan Hovold]

On Wed, Sep 04, 2024 at 12:42:00PM +0530, Manivannan Sadhasivam via B4 Relay wrote:
> From: Shashank Babu Chinta Venkata <quic_schintav at quicinc.com>
> 
> Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate. These
> settings improve link stability while operating at high date rates and
> helps to improve signal quality.
> 
> Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav at quicinc.com>
> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> [mani: dropped the code refactoring and minor changes]
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> ---
>  drivers/pci/controller/dwc/pcie-designware.h  | 18 ++++++++++++++++
>  drivers/pci/controller/dwc/pcie-qcom-common.c | 31 +++++++++++++++++++++++++++
>  drivers/pci/controller/dwc/pcie-qcom-common.h |  1 +
>  drivers/pci/controller/dwc/pcie-qcom-ep.c     |  4 +++-
>  drivers/pci/controller/dwc/pcie-qcom.c        |  4 +++-
>  5 files changed, 56 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> index 51744ad25575..f5be99731f7e 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.h
> +++ b/drivers/pci/controller/dwc/pcie-designware.h
> @@ -209,6 +209,24 @@
>  
>  #define PCIE_PL_CHK_REG_ERR_ADDR			0xB28
>  
> +/*
> + * 16.0 GT/s (GEN4) lane margining register definitions

nit: Gen 4?

> + */
> +#define GEN4_LANE_MARGINING_1_OFF		0xb80

nit: upper case hex

> +#define MARGINING_MAX_VOLTAGE_OFFSET		GENMASK(29, 24)
> +#define MARGINING_NUM_VOLTAGE_STEPS		GENMASK(22, 16)
> +#define MARGINING_MAX_TIMING_OFFSET		GENMASK(13, 8)
> +#define MARGINING_NUM_TIMING_STEPS		GENMASK(5, 0)
> +
> +#define GEN4_LANE_MARGINING_2_OFF		0xb84

Same here

> +#define MARGINING_IND_ERROR_SAMPLER		BIT(28)
> +#define MARGINING_SAMPLE_REPORTING_METHOD	BIT(27)
> +#define MARGINING_IND_LEFT_RIGHT_TIMING		BIT(26)
> +#define MARGINING_IND_UP_DOWN_VOLTAGE		BIT(25)
> +#define MARGINING_VOLTAGE_SUPPORTED		BIT(24)
> +#define MARGINING_MAXLANES			GENMASK(20, 16)
> +#define MARGINING_SAMPLE_RATE_TIMING		GENMASK(13, 8)
> +#define MARGINING_SAMPLE_RATE_VOLTAGE		GENMASK(5, 0)
>  /*
>   * iATU Unroll-specific register definitions
>   * From 4.80 core version the address translation will be made by unroll
> diff --git a/drivers/pci/controller/dwc/pcie-qcom-common.c b/drivers/pci/controller/dwc/pcie-qcom-common.c
> index dc7d93db9dc5..99b75e7f085d 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom-common.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom-common.c
> @@ -43,3 +43,34 @@ void qcom_pcie_common_set_16gt_eq_settings(struct dw_pcie *pci)
>  	dw_pcie_writel_dbi(pci, GEN3_EQ_CONTROL_OFF, reg);
>  }
>  EXPORT_SYMBOL_GPL(qcom_pcie_common_set_16gt_eq_settings);
> +
> +void qcom_pcie_common_set_16gt_rx_margining_settings(struct dw_pcie *pci)

I'd try to find a shorter symbol name here, "settings" seems redundant
after "set". Perhaps just

	qcom_pcie_common_enable_lane_margining()

or

	qcom_pcie_common_enable_16gt_lane_margining()?

if these settings are indeed specific to 16 GT/s. But perhaps it's
better to let the helper honour pci->max_link_speed if different
settings will later be needed for higher speeds:

	if (pcie_link_speed[pci->max_link_speed] >= PCIE_SPEED_16_0GT)
		qcom_pcie_common_enable_lane_margining(pci)

>  void qcom_pcie_common_set_16gt_eq_settings(struct dw_pcie *pci);
> +void qcom_pcie_common_set_16gt_rx_margining_settings(struct dw_pcie *pci);

And maybe something similar for the eq settings for symmetry.

Johan