[PATCH v6 07/12] arm64: dts: ti: k3-j784s4-j742s2-evm-common: Remove parent nodes bootph-*

Manorit Chawdhry m-chawdhry at ti.com
Wed Oct 23 22:21:04 PDT 2024


Adding bootph properties on leaf nodes imply that they are applicable to
the parent nodes as well. Bootloaders can derive the parent nodes when
bootph is available in the leaf nodes.

Remove the bootph-* properties from parent nodes as they are redundant.

Reviewed-by: Aniket Limaye <a-limaye at ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry at ti.com>
---

Notes:
    R-by picked up in v5 ( Aniket )

 arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
index 98453171a1790cd605d25ad939f556127519524a..b2e2b9f507a9828d49b1eb94d098b2c6682cef0e 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -305,7 +305,6 @@ &wkup_gpio0 {
 };
 
 &main_pmx0 {
-	bootph-all;
 	main_cpsw2g_default_pins: main-cpsw2g-default-pins {
 		pinctrl-single,pins = <
 			J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
@@ -432,7 +431,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
 };
 
 &wkup_pmx2 {
-	bootph-all;
 	wkup_uart0_pins_default: wkup-uart0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -548,7 +546,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
 };
 
 &wkup_pmx0 {
-	bootph-all;
 	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -568,7 +565,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
 };
 
 &wkup_pmx1 {
-	bootph-all;
 	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -740,18 +736,15 @@ &ufs_wrapper {
 };
 
 &fss {
-	bootph-all;
 	status = "okay";
 };
 
 &ospi0 {
-	bootph-all;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
 
 	flash at 0 {
-		bootph-all;
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;
@@ -808,13 +801,11 @@ partition at 3fc0000 {
 };
 
 &ospi1 {
-	bootph-all;
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
 
 	flash at 0 {
-		bootph-all;
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <1>;

-- 
2.46.0




More information about the linux-arm-kernel mailing list