[PATCH 1/1] arm64: dts: imx8mn-tqma8mqnl-mba8mx-usbot: fix coexistence of output-low and output-high in GPIO

[Frank Li]

Fix the issue where both 'output-low' and 'output-high' exist under GPIO
hog nodes  (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
tree overlays. Since /delete-property/ is not supported in the overlays,
setting 'output-low' results in both properties being present. The
workaround is to disable these hogs and create new ones with 'output-low'
as needed.

Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
   {'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
       is valid under each of {'required': ['output-low']}, {'required': ['output-high']

Fixes: 3f6fc30abebc ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay")
Signed-off-by: Frank Li <Frank.Li at nxp.com>
---
Alex:
	I have not hardware to run it. I check dtb output is correct.
---
 .../imx8mn-tqma8mqnl-mba8mx-usbotg.dtso       | 29 +++++++++++++++++--
 1 file changed, 27 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
index 96db07fc9bece..1f2a0fe70a0a2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
+++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtso
@@ -29,12 +29,37 @@ usb_dr_connector: endpoint {
 	};
 };
 
+/*
+ * rst_usb_hub_hog and sel_usb_hub_hog have property 'output-high',
+ * dt overlay don't support /delete-property/. Both 'output-low' and
+ * 'output-high' will be exist under hog nodes if overlay file set
+ * 'output-low'. Workaround is disable these hog and create new hog with
+ * 'output-low'.
+ */
+
 &rst_usb_hub_hog {
-	output-low;
+	status = "disabled";
+};
+
+&expander0 {
+	rst-usb-low-hub-hog {
+		gpio-hog;
+		gpios = <13 0>;
+		output-low;
+		line-name = "RST_USB_HUB#";
+	};
 };
 
 &sel_usb_hub_hog {
-	output-low;
+	status = "disabled";
+};
+
+&gpio2 {
+	sel-usb-low-hub-hog {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		output-low;
+	};
 };
 
 &usbotg1 {
-- 
2.34.1