[PATCH v5 07/12] arm64: dts: ti: k3-j784s4-j742s2-evm-common: Remove parent nodes bootph-*
Manorit Chawdhry
m-chawdhry at ti.com
Tue Oct 22 23:57:21 PDT 2024
Adding bootph properties on leaf nodes imply that they are applicable to
the parent nodes as well. Bootloaders can derive the parent nodes when
bootph is available in the leaf nodes.
Remove the bootph-* properties from parent nodes as they are redundant.
Signed-off-by: Manorit Chawdhry <m-chawdhry at ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
index 98453171a179..b2e2b9f507a9 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -305,7 +305,6 @@ &wkup_gpio0 {
};
&main_pmx0 {
- bootph-all;
main_cpsw2g_default_pins: main-cpsw2g-default-pins {
pinctrl-single,pins = <
J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
@@ -432,7 +431,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
};
&wkup_pmx2 {
- bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -548,7 +546,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
};
&wkup_pmx0 {
- bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -568,7 +565,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
- bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -740,18 +736,15 @@ &ufs_wrapper {
};
&fss {
- bootph-all;
status = "okay";
};
&ospi0 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash at 0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -808,13 +801,11 @@ partition at 3fc0000 {
};
&ospi1 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash at 0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
--
2.46.0
More information about the linux-arm-kernel
mailing list