[PATCH 2/2] ARM: dts: Reconfigure the MC2 eMMC interface

[Linus Walleij]

The eMMC interface was configured to configure the FBCLK
into the Alt A setting, but this should be in GPIO mode
and available for use as a reset line. Move it to the new
mc_a_2 setting, and define this config in the generic
options.

Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
 arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi      | 49 +++++++++++++++++++++++
 arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts | 26 +++++++-----
 2 files changed, 64 insertions(+), 11 deletions(-)

diff --git a/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi
index 31a86606bedaede9539a950c127bcd2b8d03e112..9a6304b7ab2566bc5bac49f13816cb9884398f74 100644
--- a/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi
@@ -454,6 +454,31 @@ default_cfg3 {
 			};
 		};
 
+		/* MC2 without feedback clock on A8 */
+		mc2_a_2_default: mc2_a_2_default {
+			default_mux {
+				function = "mc2";
+				groups = "mc2_a_2";
+			};
+			default_cfg1 {
+				pins = "GPIO128_A5"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins =
+				"GPIO129_B4", /* CMD */
+				"GPIO131_A12", /* DAT0 */
+				"GPIO132_C10", /* DAT1 */
+				"GPIO133_B10", /* DAT2 */
+				"GPIO134_B9", /* DAT3 */
+				"GPIO135_A9", /* DAT4 */
+				"GPIO136_C7", /* DAT5 */
+				"GPIO137_A7", /* DAT6 */
+				"GPIO138_C5"; /* DAT7 */
+				ste,config = <&in_pu>;
+			};
+		};
+
 		mc2_a_1_sleep: mc2_a_1_sleep {
 			sleep_cfg1 {
 				pins = "GPIO128_A5"; /* CLK */
@@ -478,6 +503,30 @@ sleep_cfg3 {
 				ste,config = <&in_wkup_pdis>;
 			};
 		};
+
+		mc2_a_2_sleep: mc2_a_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO128_A5"; /* CLK */
+				ste,config = <&out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO129_B4"; /* CMD */
+				ste,config = <&in_wkup_pdis_en>;
+			};
+			sleep_cfg3 {
+				pins =
+				"GPIO131_A12", /* DAT0 */
+				"GPIO132_C10", /* DAT1 */
+				"GPIO133_B10", /* DAT2 */
+				"GPIO134_B9", /* DAT3 */
+				"GPIO135_A9", /* DAT4 */
+				"GPIO136_C7", /* DAT5 */
+				"GPIO137_A7", /* DAT6 */
+				"GPIO138_C5"; /* DAT7 */
+				ste,config = <&in_wkup_pdis>;
+			};
+		};
 	};
 
 	sdi4 {
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts
index a86e7f7f391fac40f51c1409d1e614b726c481f2..40b0d92dfb1546ed6a8becf607217dcf0d18fe68 100644
--- a/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts
@@ -451,13 +451,17 @@ mmc at 80005000 {
 			no-sdio;
 			no-sd;
 			vmmc-supply = <&ldo_3v3_reg>;
+			vqmmc-supply = <&db8500_vsmps2_reg>;
 			pinctrl-names = "default", "sleep";
 			/*
-			 * GPIO130 will be set to input no pull-up resulting in a resistor
-			 * pulling the reset high and taking the memory out of reset.
+			 * This muxing excludes the feedback clock on GPIO130
+			 * which is instead used for reset of the eMMC.
+			 * GPIO130 will be set to input no pull-up resulting in
+			 * a resistor pulling the reset high and taking the
+			 * memory out of reset.
 			 */
-			pinctrl-0 = <&mc2_a_1_default>;
-			pinctrl-1 = <&mc2_a_1_sleep>;
+			pinctrl-0 = <&mc2_a_2_default>;
+			pinctrl-1 = <&mc2_a_2_sleep>;
 			status = "okay";
 		};
 
@@ -678,14 +682,14 @@ default_cfg4 {
 	sdi2 {
 		/*
 		 * This will make the resistor mounted in R0.0 pull up
-		 * the reset line and take the eMMC out of reset. On
-		 * R0.4 variants, GPIO130 should be set in GPIO mode and
-		 * pulled down. (Not connected.)
+		 * the reset line and take the eMMC out of reset so set to
+		 * GPIO input mode, no pull-up. On R0.4 variants, GPIO130
+		 * could be set in GPIO mode and pulled down. (Not connected.)
 		 */
-		mc2_a_1_default {
-			default_cfg2 {
-				pins = "GPIO130_C8"; /* FBCLK */
-				ste,config = <&in_nopull>;
+		mc2_a_2_default {
+			default_cfg3 {
+				pins = "GPIO130_C8"; /* RST_N */
+				ste,config = <&gpio_in_nopull>;
 			};
 		};
 	};

-- 
2.47.0