[PATCH v9 3/5] arm64: dts: imx8ulp-evk: add nxp secure enclave firmware

[Pankaj Gupta]

Add support for NXP secure enclave called EdgeLock Enclave
firmware (se-fw) for imx8ulp-evk.

EdgeLock Enclave has a hardware limitation of restricted access to DDR
address: 0x80000000 to 0xAFFFFFFF, so reserve 1MB of DDR memory region
from 0x80000000.

Signed-off-by: Pankaj Gupta <pankaj.gupta at nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 17 ++++++++++++++++-
 arch/arm64/boot/dts/freescale/imx8ulp.dtsi    | 13 +++++++++++--
 2 files changed, 27 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
index e937e5f8fa8b..f5963f4043c4 100644
--- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Copyright 2021 NXP
+ * Copyright 2021, 2024 NXP
  */
 
 /dts-v1/;
@@ -19,6 +19,17 @@ memory at 80000000 {
 		device_type = "memory";
 		reg = <0x0 0x80000000 0 0x80000000>;
 	};
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ele_reserved: ele-reserved at 90000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x90000000 0 0x100000>;
+			no-map;
+		};
+	};
 
 	reserved-memory {
 		#address-cells = <2>;
@@ -204,6 +215,10 @@ &usdhc0 {
 	status = "okay";
 };
 
+&ele_if0 {
+	memory-region = <&ele_reserved>;
+};
+
 &fec {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&pinctrl_enet>;
diff --git a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
index e32d5afcf4a9..f98629b7f4cc 100644
--- a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Copyright 2021 NXP
+ * Copyright 2021, 2024 NXP
  */
 
 #include <dt-bindings/clock/imx8ulp-clock.h>
@@ -152,7 +152,7 @@ sosc: clock-sosc {
 		#clock-cells = <0>;
 	};
 
-	sram at 2201f000 {
+	sram0: sram at 2201f000 {
 		compatible = "mmio-sram";
 		reg = <0x0 0x2201f000 0x0 0x1000>;
 
@@ -167,6 +167,8 @@ scmi_buf: scmi-sram-section at 0 {
 	};
 
 	firmware {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		scmi {
 			compatible = "arm,scmi-smc";
 			arm,smc-id = <0xc20000fe>;
@@ -184,6 +186,13 @@ scmi_sensor: protocol at 15 {
 				#thermal-sensor-cells = <1>;
 			};
 		};
+
+		ele_if0: secure-enclave {
+			 compatible = "fsl,imx8ulp-se";
+			 mbox-names = "tx", "rx";
+			 mboxes = <&s4muap 0 0>, <&s4muap 1 0>;
+			 sram = <&sram0>;
+		 };
 	};
 
 	cm33: remoteproc-cm33 {

-- 
2.34.1