[PATCH] arm64: dts: ti: k3-am69-sk: Add USB SuperSpeed support

[Enric Balletbo i Serra]

Hi,

On Wed, Nov 27, 2024 at 9:27 AM s-vadapalli <s-vadapalli at ti.com> wrote:
>
> On Tue, Nov 26, 2024 at 11:08:19AM +0100, Enric Balletbo i Serra wrote:
>
> Hello Enric,
>
> > From: Dasnavis Sabiya <sabiya.d at ti.com>
> >
> > AM69 SK board has two stacked USB3 connectors:
> >    1. USB3 (Stacked TypeA + TypeC)
> >    2. USB3 TypeA Hub interfaced through TUSB8041.
> >
> > The board uses SERDES0 Lane 3 for USB3 IP. So update the
> > SerDes lane info for PCIe and USB. Add the pin mux data
> > and enable USB 3.0 support with its respective SERDES settings.
> >
> > Signed-off-by: Dasnavis Sabiya <sabiya.d at ti.com>
> > Signed-off-by: Enric Balletbo i Serra <eballetb at redhat.com>
> > ---
> > I've been carrying this patch for quite long time in my builds to have
> > support for USB on my AM69-SK board without problems. For some reason this
> > patch was never send to upstream or I couldn't find it. So I took the
> > opportunity, now that I rebased my build, to send upstream.
> >
> > I have maintained the original author of the downstream patch as is
> > basically his work.
> > ---
> >  arch/arm64/boot/dts/ti/k3-am69-sk.dts | 33 +++++++++++++++++++++++++++++++++
> >  1 file changed, 33 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
>
> [...]
>
> > +&usb0 {
> > +     status = "okay";
> > +     dr_mode = "host";
>
> Since the Type-C interface is also connected to USB0, shouldn't "dr_mode"
> be "otg"? Also, has the Type-C interface been tested with this patch?
> Please let me know.
>

Yes, all usb from the board were tested. I'll try otg mode for the
Type-C interface and resend the patch.

$ lsusb -t
/:  Bus 001.Port 001: Dev 001, Class=root_hub, Driver=xhci-hcd/1p, 480M
    |__ Port 001: Dev 002, If 0, Class=Hub, Driver=hub/4p, 480M
        |__ Port 001: Dev 003, If 0, Class=Hub, Driver=hub/4p, 480M
            |__ Port 001: Dev 004, If 0, Class=Human Interface Device,
Driver=usbhid, 1.5M
            |__ Port 001: Dev 004, If 1, Class=Human Interface Device,
Driver=usbhid, 1.5M
        |__ Port 002: Dev 005, If 0, Class=Mass Storage,
Driver=usb-storage, 480M
/:  Bus 002.Port 001: Dev 001, Class=root_hub, Driver=xhci-hcd/1p, 5000M
    |__ Port 001: Dev 002, If 0, Class=Hub, Driver=hub/4p, 5000M
        |__ Port 003: Dev 004, If 0, Class=Mass Storage,
Driver=usb-storage, 5000M
        |__ Port 004: Dev 003, If 0, Class=Mass Storage,
Driver=usb-storage, 5000M

Thanks,
   Enric
> [...]
>
> Regards,
> Siddharth.
>