[PATCH v6 03/10] PCI: imx6: Fetch dbi2 and iATU base addesses from DT

[Manivannan Sadhasivam]

On Mon, Nov 18, 2024 at 02:59:35AM +0000, Hongxing Zhu wrote:
> > -----Original Message-----
> > From: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> > Sent: 2024年11月15日 14:41
> > To: Hongxing Zhu <hongxing.zhu at nxp.com>
> > Cc: l.stach at pengutronix.de; bhelgaas at google.com; lpieralisi at kernel.org;
> > kw at linux.com; robh at kernel.org; krzk+dt at kernel.org; conor+dt at kernel.org;
> > shawnguo at kernel.org; Frank Li <frank.li at nxp.com>;
> > s.hauer at pengutronix.de; festevam at gmail.com; imx at lists.linux.dev;
> > kernel at pengutronix.de; linux-pci at vger.kernel.org;
> > linux-arm-kernel at lists.infradead.org; devicetree at vger.kernel.org;
> > linux-kernel at vger.kernel.org
> > Subject: Re: [PATCH v6 03/10] PCI: imx6: Fetch dbi2 and iATU base addesses
> > from DT
> > 
> > On Fri, Nov 01, 2024 at 03:06:03PM +0800, Richard Zhu wrote:
> > > Since dbi2 and atu regs are added for i.MX8M PCIes. Fetch the dbi2 and
> > > iATU base addresses from DT directly, and remove the useless codes.
> > >
> > 
> > It'd be useful to mention where the base addresses were extraced. Like by
> > the DWC common driver.
> You're right. How about change them to the below one?
> The dw_pcie_get_resources() function of DWC core codes can fetch the dbi2 and
>  iATU base addresses from DT directly, and remove the useless codes here.

"Since dw_pcie_get_resources() gets the dbi2 and iATU base addresses from DT,
remove the code from imx6 driver that does the same."

- Mani

> 
> > 
> > > Upsteam dts's have not enabled EP function. So no function broken for
> > > old upsteam's dtb.
> > >
> > > Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> > 
> > Reviewed-by: Manivannan Sadhasivam
> > <manivannan.sadhasivam at linaro.org>
> > 
> > - Mani
> > 
> > > ---
> > >  drivers/pci/controller/dwc/pci-imx6.c | 20 --------------------
> > >  1 file changed, 20 deletions(-)
> > >
> > > diff --git a/drivers/pci/controller/dwc/pci-imx6.c
> > > b/drivers/pci/controller/dwc/pci-imx6.c
> > > index bc8567677a67..462decd1d589 100644
> > > --- a/drivers/pci/controller/dwc/pci-imx6.c
> > > +++ b/drivers/pci/controller/dwc/pci-imx6.c
> > > @@ -1115,7 +1115,6 @@ static int imx_add_pcie_ep(struct imx_pcie
> > *imx_pcie,
> > >  			   struct platform_device *pdev)
> > >  {
> > >  	int ret;
> > > -	unsigned int pcie_dbi2_offset;
> > >  	struct dw_pcie_ep *ep;
> > >  	struct dw_pcie *pci = imx_pcie->pci;
> > >  	struct dw_pcie_rp *pp = &pci->pp;
> > > @@ -1125,25 +1124,6 @@ static int imx_add_pcie_ep(struct imx_pcie
> > *imx_pcie,
> > >  	ep = &pci->ep;
> > >  	ep->ops = &pcie_ep_ops;
> > >
> > > -	switch (imx_pcie->drvdata->variant) {
> > > -	case IMX8MQ_EP:
> > > -	case IMX8MM_EP:
> > > -	case IMX8MP_EP:
> > > -		pcie_dbi2_offset = SZ_1M;
> > > -		break;
> > > -	default:
> > > -		pcie_dbi2_offset = SZ_4K;
> > > -		break;
> > > -	}
> > > -
> > > -	pci->dbi_base2 = pci->dbi_base + pcie_dbi2_offset;
> > > -
> > > -	/*
> > > -	 * FIXME: Ideally, dbi2 base address should come from DT. But since only
> > IMX95 is defining
> > > -	 * "dbi2" in DT, "dbi_base2" is set to NULL here for that platform alone
> > so that the DWC
> > > -	 * core code can fetch that from DT. But once all platform DTs were fixed,
> > this and the
> > > -	 * above "dbi_base2" setting should be removed.
> > > -	 */
> > >  	if (device_property_match_string(dev, "reg-names", "dbi2") >= 0)
> > >  		pci->dbi_base2 = NULL;
> 
> The check and the NULL assignment of "pci->dbi_base2" should be removed too
>  refer to FIXME listed above. Would updated in v7 later, Sorry about that.
> 
> Best Regards
> Richard Zhu
> > >
> > > --
> > > 2.37.1
> > >
> > 
> > --
> > மணிவண்ணன் சதாசிவம்

-- 
மணிவண்ணன் சதாசிவம்