[PATCH v4 4/4] arm64: dts: ti: k3-am69-sk: Add PCIe support

[Siddharth Vadapalli]

From: Dasnavis Sabiya <sabiya.d at ti.com>

The AM69-SK board has 3 instances of PCIe namely PCIe0, PCIe1 and PCIe3.
The x4 PCIe0 instance is connected to a Card Edge connector via SERDES1.
The x2 PCIe1 instance is connected to an M.2 M Key connector via SERDES0.
The x1 PCIe3 instance is connected to an M.2 E Key connector via SERDES0.

Add device-tree support for enabling all 3 PCIe instances in Root-Complex
mode of operation.

Signed-off-by: Dasnavis Sabiya <sabiya.d at ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli at ti.com>
---
This patch has been added newly in this series.

 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 60 +++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index d88651c297a2..14c359d810d7 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -1203,3 +1203,63 @@ partition at 3fc0000 {
 		};
 	};
 };
+
+&serdes_ln_ctrl {
+	idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+		      <J784S4_SERDES0_LANE2_PCIE3_LANE0>, <J784S4_SERDES0_LANE3_USB>,
+			<J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+			<J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>;
+};
+
+&serdes_wiz0 {
+	status = "okay";
+};
+
+&serdes0 {
+	status = "okay";
+	serdes0_pcie_link: phy at 0 {
+		reg = <0>;
+		cdns,num-lanes = <3>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>, <&serdes_wiz0 3>;
+	};
+};
+
+&serdes_wiz1 {
+	status = "okay";
+};
+
+&serdes1 {
+	status = "okay";
+	serdes1_pcie_link: phy at 0 {
+		reg = <0>;
+		cdns,num-lanes = <4>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>, <&serdes_wiz1 3>, <&serdes_wiz1 4>;
+	};
+};
+
+&pcie0_rc {
+	status = "okay";
+	reset-gpios = <&exp1 4 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes1_pcie_link>;
+	phy-names = "pcie-phy";
+};
+
+&pcie1_rc {
+	status = "okay";
+	reset-gpios = <&exp1 5 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <2>;
+};
+
+&pcie3_rc {
+	status = "okay";
+	reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+};
-- 
2.40.1