[PATCH v2 4/4] arm64: dts: broadcom: Add support for BCM2712

[Stefan Wahren]

Hi Andrea,

Am 10.05.24 um 16:35 schrieb Andrea della Porta:
> The BCM2712 SoC family can be found on Raspberry Pi 5.
> Add minimal SoC and board (Rpi5 specific) dts file to be able to
> boot from SD card and use console on debug UART.
>
> Signed-off-by: Andrea della Porta <andrea.porta at suse.com>
> ---
>   arch/arm64/boot/dts/broadcom/Makefile         |   1 +
>   .../boot/dts/broadcom/bcm2712-rpi-5-b.dts     |  62 ++++
>   arch/arm64/boot/dts/broadcom/bcm2712.dtsi     | 302 ++++++++++++++++++
>   3 files changed, 365 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
>   create mode 100644 arch/arm64/boot/dts/broadcom/bcm2712.dtsi
>
> diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
> index 8b4591ddd27c..92565e9781ad 100644
> --- a/arch/arm64/boot/dts/broadcom/Makefile
> +++ b/arch/arm64/boot/dts/broadcom/Makefile
> @@ -6,6 +6,7 @@ DTC_FLAGS := -@
>   dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
>   			      bcm2711-rpi-4-b.dtb \
>   			      bcm2711-rpi-cm4-io.dtb \
> +			      bcm2712-rpi-5-b.dtb \
>   			      bcm2837-rpi-3-a-plus.dtb \
>   			      bcm2837-rpi-3-b.dtb \
>   			      bcm2837-rpi-3-b-plus.dtb \
> diff --git a/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
> new file mode 100644
> index 000000000000..b5921437e09f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/broadcom/bcm2712-rpi-5-b.dts
> @@ -0,0 +1,62 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "bcm2712.dtsi"
> +
> +/ {
> +	compatible = "raspberrypi,5-model-b", "brcm,bcm2712";
> +	model = "Raspberry Pi 5";
> +
> +	aliases {
> +		serial10 = &uart0;
> +	};
> +
> +	chosen: chosen {
> +		stdout-path = "serial10:115200n8";
> +	};
> +
> +	/* Will be filled by the bootloader */
> +	memory at 0 {
> +		device_type = "memory";
> +		reg = <0 0 0x28000000>;
> +	};
> +
> +	sd_io_1v8_reg: sd-io-1v8-reg {
> +		compatible = "regulator-gpio";
> +		regulator-name = "vdd-sd-io";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		regulator-settling-time-us = <5000>;
> +		gpios = <&gio_aon 3 GPIO_ACTIVE_HIGH>;
> +		states = <1800000 0x1>,
> +			 <3300000 0x0>;
> +	};
> +
> +	sd_vcc_reg: sd-vcc-reg {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-sd";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		enable-active-high;
> +		gpios = <&gio_aon 4 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +/* The system UART */
Not sure this comment is helpful. Debug UART?
> +&uart0 {
> +	status = "okay";
> +};
> +
> +/* SDIO1 is used to drive the SD card */
> +&sdio1 {
> +	vqmmc-supply = <&sd_io_1v8_reg>;
> +	vmmc-supply = <&sd_vcc_reg>;
> +	bus-width = <4>;
> +	sd-uhs-sdr50;
> +	sd-uhs-ddr50;
> +	sd-uhs-sdr104;
> +};
> diff --git a/arch/arm64/boot/dts/broadcom/bcm2712.dtsi b/arch/arm64/boot/dts/broadcom/bcm2712.dtsi
> new file mode 100644
> index 000000000000..398df13148bd
> --- /dev/null
> +++ b/arch/arm64/boot/dts/broadcom/bcm2712.dtsi
> @@ -0,0 +1,302 @@
> +// SPDX-License-Identifier: GPL-2.0
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> +	compatible = "brcm,bcm2712";
> +
> +	#address-cells = <2>;
> +	#size-cells = <1>;
> +
> +	interrupt-parent = <&gicv2>;
> +
> +	axi: axi {
> +		compatible = "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		sdio1: mmc at 1000fff000 {
> +			compatible = "brcm,bcm2712-sdhci",
> +				     "brcm,sdhci-brcmstb";
> +			reg = <0x10 0x00fff000  0x260>,
> +			      <0x10 0x00fff400  0x200>;
> +			reg-names = "host", "cfg";
> +			interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clk_emmc2>;
> +			clock-names = "sw_sdio";
> +			mmc-ddr-3_3v;
> +		};
> +
> +		gicv2: interrupt-controller at 107fff9000 {
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			compatible = "arm,gic-400";
> +			reg = <0x10 0x7fff9000  0x1000>,
> +			      <0x10 0x7fffa000  0x2000>,
> +			      <0x10 0x7fffc000  0x2000>,
> +			      <0x10 0x7fffe000  0x2000>;
> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
> +				      IRQ_TYPE_LEVEL_HIGH)>;
Please take care of the DTS coding style [1].
> +		};
> +	};
> +
> +	clocks {
> +		/* The oscillator is the root of the clock tree. */
> +		clk_osc: clk-osc {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-output-names = "osc";
> +			clock-frequency = <54000000>;
> +		};
> +
> +		clk_vpu: clk-vpu {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <750000000>;
> +			clock-output-names = "vpu-clock";
> +		};
> +
> +		clk_uart: clk-uart {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <9216000>;
> +			clock-output-names = "uart-clock";
> +		};
> +
> +		clk_emmc2: clk-emmc2 {
> +			#clock-cells = <0>;
> +			compatible = "fixed-clock";
> +			clock-frequency = <200000000>;
> +			clock-output-names = "emmc2-clock";
> +		};
> +	};
> +
> +	cpus: cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		/* Source for d/i cache-line-size, cache-sets, cache-size
> +		 * https://developer.arm.com/documentation/100798/0401
> +		 * /L1-memory-system/About-the-L1-memory-system?lang=en
I think we should try to keep URLs in one line, even checkpatch
complains about it.

[1] - https://docs.kernel.org/devicetree/bindings/dts-coding-style.html