[PATCH v3 2/2] arm64: dts: ti: k3-j784s4-evm: Enable USB3 support

[Ravi Gunasekaran]

From: Matt Ranostay <mranostay at ti.com>

The board uses SERDES0 Lane 3 for USB3 IP. So update the
SerDes lane info for USB. Add the pin mux data and
enable USB3 support.

Signed-off-by: Matt Ranostay <mranostay at ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran at ti.com>
---
Changes since v2:
-----------------
* No change

Changes since v1:
----------------
* Fixed dtbs_check warning by renaming 'main-usbss0-pins-default'
  to 'main-usbss0-default-pins'

v2: https://lore.kernel.org/all/20240506052044.8228-3-r-gunasekaran@ti.com/
v1: https://lore.kernel.org/all/20240502053615.29514-3-r-gunasekaran@ti.com/

 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 41 ++++++++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index d511b25d62e3..a2d3cba0423e 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -336,6 +336,13 @@
 			J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
 		>;
 	};
+
+	main_usbss0_pins_default: main-usbss0-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AN37) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_pmx2 {
@@ -1041,6 +1048,40 @@
 				 <&k3_clks 218 22>;
 };
 
+&serdes0 {
+	status = "okay";
+
+	serdes0_usb_link: phy at 3 {
+		reg = <3>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz0 4>;
+	};
+};
+
+&serdes_wiz0 {
+	status = "okay";
+};
+
+&usb_serdes_mux {
+	idle-states = <0>; /* USB0 to SERDES lane 3 */
+};
+
+&usbss0 {
+	status = "okay";
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "super-speed";
+	phys = <&serdes0_usb_link>;
+	phy-names = "cdns3,usb3-phy";
+};
+
 &serdes_wiz4 {
 	status = "okay";
 };
-- 
2.17.1