[PATCH v2 2/2] arm64: dts: rockchip: Add Radxa ROCK 3C

[Jonas Karlman]

Hi Chukun,

On 2024-04-28 14:36, Chukun Pan wrote:
> The Radxa ROCK 3C is a development board with the
> Rockchip RK3566 SoC. It has the following features:
> 
> - 1/2/4GB LPDDR4
> - 1x HDMI Type A
> - 1x PCIE 2.0 slot
> - 1x FAN connector
> - 3.5mm jack with mic
> - 1GbE RTL8211F Ethernet
> - 1x USB 3.0, 3x USB 2.0
> - 40-pin expansion header
> - MicroSD card/eMMC socket
> - 16MB SPI NOR (gd25lq128d)
> - AP6256 or AIC8800 WiFi/BT
> 
> Signed-off-by: Chukun Pan <amadeus at jmu.edu.cn>
> ---
>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>  .../boot/dts/rockchip/rk3566-rock-3c.dts      | 750 ++++++++++++++++++
>  2 files changed, 751 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-rock-3c.dts
> 

[snip]

> +
> +&i2c0 {
> +	status = "okay";
> +
> +	vdd_cpu: regulator at 1c {
> +		compatible = "tcs,tcs4525";
> +		reg = <0x1c>;
> +		fcs,suspend-voltage-selector = <1>;
> +		regulator-name = "vdd_cpu";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <800000>;
> +		regulator-max-microvolt = <1150000>;
> +		regulator-ramp-delay = <2300>;
> +		vin-supply = <&vcc5v0_sys>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	rk809: pmic at 20 {
> +		compatible = "rockchip,rk809";
> +		reg = <0x20>;

[snip]

> +		codec {
> +			mic-in-differential;

This should be rockchip,mic-in-differential or removed.

> +		};
> +	};
> +
> +	eeprom: eeprom at 50 {
> +		compatible = "belling,bl24c16a", "atmel,24c16";
> +		reg = <0x50>;
> +		pagesize = <16>;
> +	};
> +};
> +

[snip]

> +
> +&sdmmc0 {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	disable-wp;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> +	sd-uhs-sdr50;

Do you have any references to issues related to why sd-uhs-sdr104 is not
used here?

My testing shows that io-domain is getting notified and correctly
configured during boot. And card seem to be working correctly.

[    2.162780] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)

[    2.229408] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[    2.230042] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[    2.231493] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000
[    2.232121] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000 done
[    2.257294] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[    2.269482] dwmmc_rockchip fe2b0000.mmc: Successfully tuned phase to 254
[    2.270098] mmc1: new ultra high speed SDR104 SDXC card at address aaaa
[    2.271533] mmcblk1: mmc1:aaaa SD64G 59.5 GiB
[    2.277357]  mmcblk1: p1

Also when the card is later removed/re-inserted:

[   80.181598] mmc1: card aaaa removed
[   83.836785] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[   83.837611] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[   83.839263] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[   83.839952] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[   83.855358] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[   84.153827] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000
[   84.154524] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 3300000 done
[   84.156149] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000
[   84.156838] rockchip-iodomain fdc20000.syscon:io-domains: Setting to 1800000 done
[   84.183932] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[   84.202888] dwmmc_rockchip fe2b0000.mmc: Successfully tuned phase to 257
[   84.203574] mmc1: new ultra high speed SDR104 SDXC card at address aaaa
[   84.205537] mmcblk1: mmc1:aaaa SD64G 59.5 GiB
[   84.211434]  mmcblk1: p1

sd-uhs-ddr50 should also work based on my testing.

Regards,
Jonas

> +	vmmc-supply = <&vcc3v3_sys>;
> +	vqmmc-supply = <&vccio_sd>;
> +	status = "okay";
> +};
> +

[snip]