[PATCH v7 4/5] arm64: dts: ti: k3-j784s4: Add overlay to enable QSGMII mode with CPSW9G
Chintan Vankar
c-vankar at ti.com
Thu May 2 02:10:01 PDT 2024
From: Siddharth Vadapalli <s-vadapalli at ti.com>
The J7 Quad Port Add-On Ethernet Card for J784S4 EVM supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII
mode with the Add-On Ethernet Card connected to the ENET Expansion
1 slot on the EVM.
Add support to reset the PHY from kernel by using gpio-hog and
gpio-reset.
Add aliases for CPSW9G ports to enable kernel to fetch MAC Addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli at ti.com>
Signed-off-by: Chintan Vankar <c-vankar at ti.com>
---
Link to v6:
https://lore.kernel.org/r/20240329053130.2822129-5-c-vankar@ti.com/
Changes from v6 to v7:
- No changes.
arch/arm64/boot/dts/ti/Makefile | 7 +-
.../ti/k3-j784s4-evm-quad-port-eth-exp1.dtso | 147 ++++++++++++++++++
2 files changed, 153 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 2c327cc320cf..bb3ca0d17788 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
# Boards with J784s4 SoC
dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
# Build time test only, enabled by CONFIG_OF_ALL_DTBS
k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
@@ -148,6 +149,8 @@ k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \
k3-j721e-sk-csi2-dual-imx219.dtbo
k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \
k3-j721s2-evm-pcie1-ep.dtbo
+k3-j784s4-evm-quad-port-eth-exp1-dtbs := k3-j784s4-evm.dtb \
+ k3-j784s4-evm-quad-port-eth-exp1.dtbo
dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am625-beagleplay-csi2-tevi-ov5640.dtb \
k3-am625-sk-csi2-imx219.dtb \
@@ -168,7 +171,8 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am69-sk-csi2-dual-imx219.dtb \
k3-j721e-evm-pcie0-ep.dtb \
k3-j721e-sk-csi2-dual-imx219.dtb \
- k3-j721s2-evm-pcie1-ep.dtb
+ k3-j721s2-evm-pcie1-ep.dtb \
+ k3-j784s4-evm-quad-port-eth-exp1.dtb
# Enable support for device-tree overlays
DTC_FLAGS_k3-am625-beagleplay += -@
@@ -186,3 +190,4 @@ DTC_FLAGS_k3-am69-sk += -@
DTC_FLAGS_k3-j721e-common-proc-board += -@
DTC_FLAGS_k3-j721e-sk += -@
DTC_FLAGS_k3-j721s2-common-proc-board += -@
+DTC_FLAGS_k3-j784s4-evm += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso b/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
new file mode 100644
index 000000000000..dcd2c7c39ec3
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
@@ -0,0 +1,147 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/**
+ * DT Overlay for CPSW9G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
+ * J784S4 EVM. The Add-On Ethernet Card has to be connected to ENET Expansion 1 slot on the
+ * board.
+ *
+ * Product Datasheet: https://www.ti.com/lit/ug/spruj74/spruj74.pdf
+ *
+ * Link to QSGMII Daughtercard: https://www.ti.com/tool/J721EXENETXPANEVM
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-pinctrl.h"
+#include "k3-serdes.h"
+
+&{/} {
+ aliases {
+ ethernet1 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 5";
+ ethernet2 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 6";
+ ethernet3 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 7";
+ ethernet4 = "/bus at 100000/ethernet at c000000/ethernet-ports/port at 8";
+ ethernet5 = "/bus at 100000/ethernet at c200000/ethernet-ports/port at 1";
+ };
+};
+
+&main_cpsw0 {
+ status = "okay";
+};
+
+&main_cpsw0_port5 {
+ phy-handle = <&cpsw9g_phy1>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 5>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+ status = "okay";
+};
+
+&main_cpsw0_port6 {
+ phy-handle = <&cpsw9g_phy2>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 6>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+ status = "okay";
+};
+
+&main_cpsw0_port7 {
+ phy-handle = <&cpsw9g_phy0>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 7>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+ status = "okay";
+};
+
+&main_cpsw0_port8 {
+ phy-handle = <&cpsw9g_phy3>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 8>, <&serdes2_qsgmii_link>;
+ phy-names = "mac", "serdes";
+ status = "okay";
+};
+
+&main_cpsw0_mdio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio0_default_pins>;
+ bus_freq = <1000000>;
+ reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
+ reset-post-delay-us = <120000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ cpsw9g_phy0: ethernet-phy at 16 {
+ reg = <16>;
+ };
+ cpsw9g_phy1: ethernet-phy at 17 {
+ reg = <17>;
+ };
+ cpsw9g_phy2: ethernet-phy at 18 {
+ reg = <18>;
+ };
+ cpsw9g_phy3: ethernet-phy at 19 {
+ reg = <19>;
+ };
+};
+
+&exp2 {
+ /* Power-up ENET1 EXPANDER PHY. */
+ qsgmii-line-hog {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ };
+
+ /* Toggle MUX2 for MDIO lines */
+ mux-sel-hog {
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>, <14 GPIO_ACTIVE_HIGH>, <15 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+};
+
+&main_pmx0 {
+ mdio0_default_pins: mdio0-default-pins {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x05c, PIN_INPUT, 4) /* (AC36) MCASP2_AXR0.MDIO1_MDIO */
+ J784S4_IOPAD(0x058, PIN_INPUT, 4) /* (AE37) MCASP2_AFSX.MDIO1_MDC */
+ >;
+ };
+};
+
+&serdes_ln_ctrl {
+ idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+ <J784S4_SERDES0_LANE2_IP3_UNUSED>, <J784S4_SERDES0_LANE3_USB>,
+ <J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+ <J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
+ <J784S4_SERDES2_LANE0_QSGMII_LANE5>, <J784S4_SERDES2_LANE1_QSGMII_LANE6>,
+ <J784S4_SERDES2_LANE2_QSGMII_LANE7>, <J784S4_SERDES2_LANE3_QSGMII_LANE8>;
+};
+
+&serdes_wiz2 {
+ status = "okay";
+};
+
+&serdes2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+ serdes2_qsgmii_link: phy at 0 {
+ reg = <2>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_QSGMII>;
+ resets = <&serdes_wiz2 3>;
+ };
+};
--
2.34.1
More information about the linux-arm-kernel
mailing list