[PATCH v4 1/5] dt-bindings: misc: Add mikrobus-connector

[Ayush Singh]

On 3/18/24 17:52, Michael Walle wrote:

> On Sun Mar 17, 2024 at 8:37 PM CET, Ayush Singh wrote:
>> Add DT bindings for mikroBUS interface. MikroBUS is an open standard
>> developed by MikroElektronika for connecting add-on boards to
>> microcontrollers or microprocessors.
>>
>> mikroBUS is a connector and does not have a controller. Instead the
>> software is responsible for identification of board and setting up /
>> registering uart, spi, i2c, pwm and other buses. Thus it needs a way to
>> get uart, spi, i2c, pwm and gpio controllers / adapters.
>>
>> A mikroBUS addon board is free to leave some of the pins unused which
>> are marked as NC or Not Connected.
>>
>> Some of the pins might need to be configured as GPIOs deviating from their
>> reserved purposes Eg: SHT15 Click where the SCL and SDA Pins need to be
>> configured as GPIOs for the driver (drivers/hwmon/sht15.c) to work.
>>
>> For some add-on boards the driver may not take care of some additional
>> signals like reset/wake-up/other. Eg: ENC28J60 click where the reset line
>> (RST pin on the mikrobus port) needs to be pulled high.
>>
>> Here's the list of pins in mikroBUS connector:
>> Analog - AN
>> Reset - RST
>> SPI Chip Select - CS
>> SPI Clock - SCK
>> SPI Master Input Slave Output - MISO
>> SPI Master Output Slave Input - MOSI
>> VCC-3.3V power - +3.3V
>> Reference Ground - GND
>> PWM - PWM output
>> INT - Hardware Interrupt
>> RX - UART Receive
>> TX - UART Transmit
>> SCL - I2C Clock
>> SDA - I2C Data
>> +5V - VCC-5V power
>> GND - Reference Ground
>>
>> Additionally, some new mikroBUS boards contain 1-wire EEPROM that contains
>> a manifest to describe the addon board to provide plug and play
>> capabilities.
>>
>> Link: https://www.mikroe.com/mikrobus
>> Link:
>> https://download.mikroe.com/documents/standards/mikrobus/mikrobus-standard-specification-v200.pdf
>> mikroBUS specification
>> Link: https://www.mikroe.com/sht1x-click SHT15 Click
>> Link: https://www.mikroe.com/eth-click ENC28J60 Click
>> Link: https://www.mikroe.com/clickid ClickID
>>
>> Co-developed-by: Vaishnav M A <vaishnav at beagleboard.org>
>> Signed-off-by: Vaishnav M A <vaishnav at beagleboard.org>
>> Signed-off-by: Ayush Singh <ayushdevel1325 at gmail.com>
>> ---
>>   .../connector/mikrobus-connector.yaml         | 113 ++++++++++++++++++
> See also
> https://lore.kernel.org/r/YmFo+EntwxIsco%2Ft@robh.at.kernel.org/
>
> Looks like this proposal doesn't have the subnodes. How do you
> attach a kernel driver to it's spi port for example? Only through
> the manifest files?
>
> -michael


So I looked at the Patch, and it seems the approach of fundamentally 
different than this PR. So, let me try to explain what this patch set 
does for an add-on board using SPI.

The device tree defines the SPI controller associated with mikroBUS SPI 
pins. The driver on match queries and takes a reference to the SPI 
controller but does nothing with it. Once a mikroBUS add-on board is 
detected (by passing manifest using sysfs or reading from 1-wire 
EEPROM), the driver parses the manifest, and if it detects an SPI device 
in manifest, it registers SPI device along with setting properties such 
as `chip_select`, `max_speed_hz`, `mode`, etc., which are defined in the 
manifest. On board removal, it unregisters the SPI device and waits for 
a new mikroBUS board to be detected again.

It is also possible for SPI not to be used by a device, in which case, 
no SPI device is registered to the controller. It is also possible that 
the SPI pins will be used as normal GPIOs. Everything is identified from 
the manifest.


Ayush Singh