[PATCH 1/3] arm64: dts: S32G3: Introduce device tree for S32G-VNP-RDB3
Wadim Mueller
wafgo01 at gmail.com
Mon Mar 18 02:34:18 PDT 2024
On Mon, Mar 18, 2024 at 09:32:24AM +0200, Ghennadi Procopciuc wrote:
> On 3/16/24 00:27, Wadim Mueller wrote:
> > This commit adds device tree support for the NXP S32G3-based
> > S32G-VNP-RDB3 Board (Vehicle Networking Platform - Reference Design Board) [1].
> >
> > The S32G3 features an 8-core ARM Cortex-A53 based SoC developed by NXP.
> >
> > The device tree files are derived from the official NXP downstream Linux tree [2].
> >
> > This addition encompasses a limited selection of peripherals that are upstream-supported. Apart from the ARM System Modules (GIC, Generic Timer, etc.), the following IPs have been validated:
> >
> > UART: fsl-linflexuart
> > SDHC: fsl-imx-esdhc
> > Ethernet: synopsys gmac/stmac
> >
> > Clock settings for the chip rely on ATF Firmware [3]. Pin control integration into the device tree is pending and currently relies on Firmware/U-Boot settings [4].
> >
> > These changes were validated using the latest BSP39 Firmware/U-Boot from NXP [5].
> >
> > The modifications enable booting the official Ubuntu 22.04 from NXP on
> > the RDB3 with default settings from the SD card and eMMC.
> >
> > [1] https://www.nxp.com/design/design-center/designs/s32g3-vehicle-networking-reference-design:S32G-VNP-RDB3
> > [2] https://github.com/nxp-auto-linux/linux
> > [3] https://github.com/nxp-auto-linux/arm-trusted-firmware
> > [4] https://github.com/nxp-auto-linux/u-boot
> > [5] https://github.com/nxp-auto-linux/auto_yocto_bsp
> >
> > Signed-off-by: Wadim Mueller <wafgo01 at gmail.com>
>
> This patch seems to be heavily based on the downstream version of the
> kernel. Many of the changes originate from NXP. Therefore, shouldn't the
> authors also be mentioned here?
>
Yes, it definitely is, I also mentionaed it in the commit message. As
Krzyszof mentioned, would you expect me to "git blame" the file and put
all contributors into the commment part? Or would it be enough to put a
Copyright of NXP as here [1]?
[1] https://github.com/nxp-auto-linux/linux/blob/cdac0506874b7e6a277f12e72e3900d2a410d909/arch/arm64/boot/dts/freescale/s32g3.dtsi#L3
> > ---
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > arch/arm64/boot/dts/freescale/s32g3.dtsi | 352 ++++++++++++++++++
> > .../boot/dts/freescale/s32g399a-rdb3.dts | 57 +++
> > .../dt-bindings/clock/nxp,s32-scmi-clock.h | 158 ++++++++
> > 4 files changed, 568 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/s32g3.dtsi
> > create mode 100644 arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts
> > create mode 100644 include/dt-bindings/clock/nxp,s32-scmi-clock.h
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 2cb0212b63c6..e701008dbc7b 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -252,3 +252,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw74xx-rpidsi.dtb
> > dtb-$(CONFIG_ARCH_S32) += s32g274a-evb.dtb
> > dtb-$(CONFIG_ARCH_S32) += s32g274a-rdb2.dtb
> > dtb-$(CONFIG_ARCH_S32) += s32v234-evb.dtb
> > +dtb-$(CONFIG_ARCH_S32) += s32g399a-rdb3.dtb
> > diff --git a/arch/arm64/boot/dts/freescale/s32g3.dtsi b/arch/arm64/boot/dts/freescale/s32g3.dtsi
> > new file mode 100644
> > index 000000000000..481ddcfd3a6d
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/s32g3.dtsi
> > @@ -0,0 +1,352 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include <dt-bindings/clock/nxp,s32-scmi-clock.h>
> > +/ {
> > + compatible = "nxp,s32g3";
> > + interrupt-parent = <&gic>;
> > + #address-cells = <0x02>;
> > + #size-cells = <0x02>;
> > +
> > + cpus {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&cpu0>;
> > + };
> > +
> > + core1 {
> > + cpu = <&cpu1>;
> > + };
> > +
> > + core2 {
> > + cpu = <&cpu2>;
> > + };
> > +
> > + core3 {
> > + cpu = <&cpu3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&cpu4>;
> > + };
> > +
> > + core1 {
> > + cpu = <&cpu5>;
> > + };
> > +
> > + core2 {
> > + cpu = <&cpu6>;
> > + };
> > +
> > + core3 {
> > + cpu = <&cpu7>;
> > + };
> > + };
> > + };
> > +
> > + cpu0: cpu at 0 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x0>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster0_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
>
> Are the '#cooling-cells = <2>;' used in this patch? If not, shouldn't
> you drop them?
>
No, its not used. Will drop it, thanks for the hint!
> > +
> > + cpu1: cpu at 1 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x1>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster0_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu2: cpu at 2 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x2>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster0_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu3: cpu at 3 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x3>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster0_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu4: cpu at 100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x100>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster1_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu5: cpu at 101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x101>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster1_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu6: cpu at 102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x102>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster1_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu7: cpu at 103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x103>;
> > + enable-method = "psci";
> > + clocks = <&dfs S32_SCMI_CLK_A53>;
> > + next-level-cache = <&cluster1_l2_cache>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cluster0_l2_cache: l2-cache0 {
> > + compatible = "cache";
> > + status = "okay";
> > + };
> > +
> > + cluster1_l2_cache: l2-cache1 {
> > + compatible = "cache";
> > + status = "okay";
> > + };
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu";
> > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* sec-phys */
> > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* virt */
> > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* hyp-virt */
> > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>, /* sec-phys */
> > + <GIC_PPI 12 IRQ_TYPE_LEVEL_LOW>; /* phys */
> > + always-on;
> > + };
>
> 1. 'always-on' -> 'arm,no-tick-in-suspend' as the timer does not tick
> during suspend on this platform.
>
> 2. The ARMv8 timer driver expects a certain order of interrupts
> when the interrupt names are not used in bindings which is not followed
> in this node.
>
> Here is the fix to be applied:
> https://github.com/nxp-auto-linux/linux/commit/f23552d3f8d8f3893dc5b485ba79ee73895f5b27
>
1) thanks, whill change it!
2) I wanted to avoid to create the interrupt-names property and directly
put it in the right order, or do you see here a wrong order to what is
erxpected by the arch_timer driver? Is your proposal to also use the interrupt-names property
instead or a ordering it according the dt schema?
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + scmi_tx_buf: shm at d0000000 {
> > + compatible = "arm,scmi-shmem";
> > + reg = <0x0 0xd0000000 0x0 0x80>;
> > + no-map;
> > + };
> > +
> > + scmi_rx_buf: shm at d0000080 {
> > + compatible = "arm,scmi-shmem";
> > + reg = <0x0 0xd0000080 0x0 0x80>;
> > + no-map;
> > + };
> > + };
> > +
> > + firmware {
> > + scmi: scmi {
> > + compatible = "arm,scmi-smc";
> > + mbox-names = "tx", "rx";
> > + shmem = <&scmi_tx_buf>, <&scmi_rx_buf>;
>
> Have you verified the RX support?
>
> > + arm,smc-id = <0xc20000fe>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > + interrupts = <GIC_SPI 300 IRQ_TYPE_EDGE_RISING>;
> > + interrupt-names = "p2a_notif";
>
> This support is not available upstream and, therefore, should be either
> removed or completely added.
>
Thanks, will do that in v2!
> > +
> > + dfs: protocol at 13 {
> > + reg = <0x13>;
> > + #clock-cells = <1>;
> > + };
> > +
> > + clks: protocol at 14 {
> > + reg = <0x14>;
> > + #clock-cells = <1>;
> > + };
> > +
> > + reset: protocol at 16 {
> > + reg = <0x16>;
> > + #reset-cells = <1>;
> > + };
>
> Is this really needed to be part of this patch?
>
No the reset node is not really needed, I forgot to remove it, thanks
for the hint!
> > +
> > + pinctrl_scmi: protocol at 80 {
> > + reg = <0x80>;
> > + #pinctrl-cells = <2>;
> > +
> > + status = "disabled";
> > + };
>
> Not documented.
>
Will be removed as not used
> > + };
> > +
> > + psci: psci {
> > + compatible = "arm,psci-1.0";
> > + method = "smc";
> > + };
> > + };
> > +
> > + soc at 0 {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0 0 0x80000000>;
> > +
> > + uart0: serial at 401c8000 {
> > + compatible = "nxp,s32g3-linflexuart",
> > + "fsl,s32v234-linflexuart";
> > + reg = <0x401c8000 0x3000>;
> > + interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial at 401cc000 {
> > + compatible = "nxp,s32g3-linflexuart",
> > + "fsl,s32v234-linflexuart";
> > + reg = <0x401cc000 0x3000>;
> > + interrupts = <GIC_SPI 83 IRQ_TYPE_EDGE_RISING>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial at 402bc000 {
> > + compatible = "nxp,s32g3-linflexuart",
> > + "fsl,s32v234-linflexuart";
> > + reg = <0x402bc000 0x3000>;
> > + interrupts = <GIC_SPI 84 IRQ_TYPE_EDGE_RISING>;
> > + status = "disabled";
> > + };
> > +
> > + gic: interrupt-controller at 50800000 {
> > + compatible = "arm,gic-v3";
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + reg = <0x50800000 0x10000>,
> > + <0x50900000 0x200000>,
> > + <0x50400000 0x2000>,
> > + <0x50410000 0x2000>,
> > + <0x50420000 0x2000>;
> > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> > + mbi-ranges = <167 16>;
> > + };
> > +
> > + qspi: spi at 40134000 {
> > + compatible = "nxp,s32g3-qspi";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x0 0x00000000 0x0 0x20000000>,
> > + <0x0 0x40134000 0x0 0x1000>;
> > + reg-names = "QuadSPI-memory", "QuadSPI";
> > + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> > + clock-names = "qspi_en", "qspi";
> > + clocks = <&clks S32_SCMI_CLK_QSPI_FLASH1X>,
> > + <&clks S32_SCMI_CLK_QSPI_FLASH1X>;
> > + spi-max-frequency = <200000000>;
> > + spi-num-chipselects = <2>;
> > + status = "disabled";
> > + };
>
> This binding and support is missing. Please delete.
>
> > +
> > + usdhc0: mmc at 402f0000 {
> > + compatible = "nxp,s32g3-usdhc",
> > + "nxp,s32g2-usdhc";
> > + reg = <0x402f0000 0x1000>;
> > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&clks S32_SCMI_CLK_USDHC_MODULE>,
> > + <&clks S32_SCMI_CLK_USDHC_AHB>,
> > + <&clks S32_SCMI_CLK_USDHC_CORE>;
> > + clock-names = "ipg", "ahb", "per";
> > + status = "disabled";
> > + };
>
> nxp,s32g3-usdhc is not documented.
>
Would you propose to delete the compatible string, or add the
documentation of nxp,s32g3-usdhc to the schema? The driver seems to work pretty fine
without any g3 specific adaptations.
> > +
> > + gmac0: ethernet at 4033c000 {
> > + status = "disabled";
> > + compatible = "nxp,s32-dwmac";
> > + reg = <0x4033c000 0x2000>, /* gmac IP */
> > + <0x4007c004 0x4>; /* S32 CTRL_STS reg */
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "macirq";
> > + tx-fifo-depth = <20480>;
> > + rx-fifo-depth = <20480>;
> > + dma-coherent;
> > + snps,mtl-rx-config = <&mtl_rx_setup_gmac0>;
> > + snps,mtl-tx-config = <&mtl_tx_setup_gmac0>;
> > + clocks = <&clks S32_SCMI_CLK_GMAC0_AXI>,
> > + <&clks S32_SCMI_CLK_GMAC0_AXI>,
> > + <&clks S32_SCMI_CLK_GMAC0_TX_SGMII>,
> > + <&clks S32_SCMI_CLK_GMAC0_TX_RGMII>,
> > + <&clks S32_SCMI_CLK_GMAC0_TX_RMII>,
> > + <&clks S32_SCMI_CLK_GMAC0_TX_MII>,
> > + <&clks S32_SCMI_CLK_GMAC0_RX_SGMII>,
> > + <&clks S32_SCMI_CLK_GMAC0_RX_RGMII>,
> > + <&clks S32_SCMI_CLK_GMAC0_RX_RMII>,
> > + <&clks S32_SCMI_CLK_GMAC0_RX_MII>,
> > + <&clks S32_SCMI_CLK_GMAC0_TS>;
> > + clock-names = "stmmaceth", "pclk",
> > + "tx_sgmii", "tx_rgmii",
> > + "tx_rmii", "tx_mii",
> > + "rx_sgmii", "rx_rgmii",
> > + "rx_rmii", "rx_mii",
> > + "ptp_ref";
> > +
> > + mtl_rx_setup_gmac0: rx-queues-config {
> > + snps,rx-queues-to-use = <5>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + queue at 0 {};
> > + queue at 1 {};
> > + queue at 2 {};
> > + queue at 3 {};
> > + queue at 4 {};
> > + };
> > +
> > + mtl_tx_setup_gmac0: tx-queues-config {
> > + snps,tx-queues-to-use = <5>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + queue at 0 {};
> > + queue at 1 {};
> > + queue at 2 {};
> > + queue at 3 {};
> > + queue at 4 {};
> > + };
> > +
> > + gmac0_mdio: mdio0 {
> > + compatible = "snps,dwmac-mdio";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + };
> > + };
> > +
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts
> > new file mode 100644
> > index 000000000000..707b503c0165
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/s32g399a-rdb3.dts
> > @@ -0,0 +1,57 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * NXP S32G3 Reference Design Board 3 (S32G-VNP-RDB3)
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "s32g3.dtsi"
> > +
> > +/ {
> > + model = "NXP S32G3 Reference Design Board 3 (S32G-VNP-RDB3)";
> > + compatible = "nxp,s32g399a-rdb3", "nxp,s32g3";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + serial1 = &uart1;
> > + ethernet0 = &gmac0;
> > + reset = &reset;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + /* 4GiB RAM */
> > + memory at 80000000 {
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x80000000>,
> > + <0x8 0x80000000 0 0x80000000>;
> > + };
> > +};
> > +
> > +&gmac0 {
> > + status = "okay";
> > + phy-handle = <&mdio_a_phy1>;
> > + phy-mode = "rgmii-id";
> > +};
> > +
> > +&gmac0_mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + mdio_a_phy1: ethernet-phy at 1 {
> > + reg = <1>;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&usdhc0 {
> > + status = "okay";
> > +};
> > diff --git a/include/dt-bindings/clock/nxp,s32-scmi-clock.h b/include/dt-bindings/clock/nxp,s32-scmi-clock.h
> > new file mode 100644
> > index 000000000000..240022c1f109
> > --- /dev/null
> > +++ b/include/dt-bindings/clock/nxp,s32-scmi-clock.h
> > @@ -0,0 +1,158 @@
> > +/* SPDX-License-Identifier: BSD-3-Clause */
> > +
> > +#ifndef __DT_BINDINGS_NXP_SCMI_CLOCK_S32_H
> > +#define __DT_BINDINGS_NXP_SCMI_CLOCK_S32_H
> > +
> > +#define S32_SCMI_COMPLEX_CLK 0xFFFFFFFFU
> > +#define S32_SCMI_NOT_IMPLEMENTED_CLK 0xFFFFFFFEU
> > +
> > +#define S32_SCMI_CLK_BASE_ID 0U
> > +#define S32_SCMI_CLK(N) ((N) + S32_SCMI_CLK_BASE_ID)
> > +#define S32_PLAT_SCMI_CLK(N) ((N) + S32_SCMI_PLAT_CLK_BASE_ID)
> > +
> > +#define S32_SCMI_CLK_VERSION_MAJOR (1)
> > +#define S32_SCMI_CLK_VERSION_MINOR (0)
> > +
> > +/* A53 */
> > +#define S32_SCMI_CLK_A53 S32_SCMI_CLK(0)
> > +/* SERDES */
> > +#define S32_SCMI_CLK_SERDES_AXI S32_SCMI_CLK(1)
> > +#define S32_SCMI_CLK_SERDES_AUX S32_SCMI_CLK(2)
> > +#define S32_SCMI_CLK_SERDES_APB S32_SCMI_CLK(3)
> > +#define S32_SCMI_CLK_SERDES_REF S32_SCMI_CLK(4)
> > +/* FTM0 */
> > +#define S32_SCMI_CLK_FTM0_SYS S32_SCMI_CLK(5)
> > +#define S32_SCMI_CLK_FTM0_EXT S32_SCMI_CLK(6)
> > +/* FTM1 */
> > +#define S32_SCMI_CLK_FTM1_SYS S32_SCMI_CLK(7)
> > +#define S32_SCMI_CLK_FTM1_EXT S32_SCMI_CLK(8)
> > +/* FlexCAN */
> > +#define S32_SCMI_CLK_FLEXCAN_REG S32_SCMI_CLK(9)
> > +#define S32_SCMI_CLK_FLEXCAN_SYS S32_SCMI_CLK(10)
> > +#define S32_SCMI_CLK_FLEXCAN_CAN S32_SCMI_CLK(11)
> > +#define S32_SCMI_CLK_FLEXCAN_TS S32_SCMI_CLK(12)
> > +/* LINFlexD */
> > +#define S32_SCMI_CLK_LINFLEX_XBAR S32_SCMI_CLK(13)
> > +#define S32_SCMI_CLK_LINFLEX_LIN S32_SCMI_CLK(14)
> > +#define S32_SCMI_CLK_GMAC0_TS S32_SCMI_CLK(15)
> > +/* GMAC0 - SGMII */
> > +#define S32_SCMI_CLK_GMAC0_RX_SGMII S32_SCMI_CLK(16)
> > +#define S32_SCMI_CLK_GMAC0_TX_SGMII S32_SCMI_CLK(17)
> > +/* GMAC0 - RGMII */
> > +#define S32_SCMI_CLK_GMAC0_RX_RGMII S32_SCMI_CLK(18)
> > +#define S32_SCMI_CLK_GMAC0_TX_RGMII S32_SCMI_CLK(19)
> > +/* GMAC0 - RMII */
> > +#define S32_SCMI_CLK_GMAC0_RX_RMII S32_SCMI_CLK(20)
> > +#define S32_SCMI_CLK_GMAC0_TX_RMII S32_SCMI_CLK(21)
> > +/* GMAC0 - MII */
> > +#define S32_SCMI_CLK_GMAC0_RX_MII S32_SCMI_CLK(22)
> > +#define S32_SCMI_CLK_GMAC0_TX_MII S32_SCMI_CLK(23)
> > +#define S32_SCMI_CLK_GMAC0_AXI S32_SCMI_CLK(24)
> > +/* SPI */
> > +#define S32_SCMI_CLK_SPI_REG S32_SCMI_CLK(25)
> > +#define S32_SCMI_CLK_SPI_MODULE S32_SCMI_CLK(26)
> > +/* QSPI */
> > +#define S32_SCMI_CLK_QSPI_REG S32_SCMI_CLK(27)
> > +#define S32_SCMI_CLK_QSPI_AHB S32_SCMI_CLK(28)
> > +#define S32_SCMI_CLK_QSPI_FLASH2X S32_SCMI_CLK(29)
> > +#define S32_SCMI_CLK_QSPI_FLASH1X S32_SCMI_CLK(30)
> > +/* uSDHC */
> > +#define S32_SCMI_CLK_USDHC_AHB S32_SCMI_CLK(31)
> > +#define S32_SCMI_CLK_USDHC_MODULE S32_SCMI_CLK(32)
> > +#define S32_SCMI_CLK_USDHC_CORE S32_SCMI_CLK(33)
> > +#define S32_SCMI_CLK_USDHC_MOD32K S32_SCMI_CLK(34)
> > +/* DDR */
> > +#define S32_SCMI_CLK_DDR_REG S32_SCMI_CLK(35)
> > +#define S32_SCMI_CLK_DDR_PLL_REF S32_SCMI_CLK(36)
> > +#define S32_SCMI_CLK_DDR_AXI S32_SCMI_CLK(37)
> > +/* SRAM */
> > +#define S32_SCMI_CLK_SRAM_AXI S32_SCMI_CLK(38)
> > +#define S32_SCMI_CLK_SRAM_REG S32_SCMI_CLK(39)
> > +/* I2C */
> > +#define S32_SCMI_CLK_I2C_REG S32_SCMI_CLK(40)
> > +#define S32_SCMI_CLK_I2C_MODULE S32_SCMI_CLK(41)
> > +/* SIUL2 */
> > +#define S32_SCMI_CLK_SIUL2_REG S32_SCMI_CLK(42)
> > +#define S32_SCMI_CLK_SIUL2_FILTER S32_SCMI_CLK(43)
> > +/* CRC */
> > +#define S32_SCMI_CLK_CRC_REG S32_SCMI_CLK(44)
> > +#define S32_SCMI_CLK_CRC_MODULE S32_SCMI_CLK(45)
> > +/* EIM0 */
> > +#define S32_SCMI_CLK_EIM0_REG S32_SCMI_CLK(46)
> > +#define S32_SCMI_CLK_EIM0_MODULE S32_SCMI_CLK(47)
> > +/* EIM0 */
> > +#define S32_SCMI_CLK_EIM123_REG S32_SCMI_CLK(48)
> > +#define S32_SCMI_CLK_EIM123_MODULE S32_SCMI_CLK(49)
> > +/* EIM */
> > +#define S32_SCMI_CLK_EIM_REG S32_SCMI_CLK(50)
> > +#define S32_SCMI_CLK_EIM_MODULE S32_SCMI_CLK(51)
> > +/* FCCU */
> > +#define S32_SCMI_CLK_FCCU_MODULE S32_SCMI_CLK(52)
> > +#define S32_SCMI_CLK_FCCU_SAFE S32_SCMI_CLK(53)
> > +/* RTC */
> > +#define S32_SCMI_CLK_RTC_REG S32_SCMI_CLK(54)
> > +#define S32_SCMI_CLK_RTC_SIRC S32_SCMI_CLK(55)
> > +#define S32_SCMI_CLK_RTC_FIRC S32_SCMI_CLK(56)
> > +/* SWT */
> > +#define S32_SCMI_CLK_SWT_MODULE S32_SCMI_CLK(57)
> > +#define S32_SCMI_CLK_SWT_COUNTER S32_SCMI_CLK(58)
> > +/* STM */
> > +#define S32_SCMI_CLK_STM_MODULE S32_SCMI_CLK(59)
> > +#define S32_SCMI_CLK_STM_REG S32_SCMI_CLK(60)
> > +/* PIT */
> > +#define S32_SCMI_CLK_PIT_MODULE S32_SCMI_CLK(61)
> > +#define S32_SCMI_CLK_PIT_REG S32_SCMI_CLK(62)
> > +/* eDMA */
> > +#define S32_SCMI_CLK_EDMA_MODULE S32_SCMI_CLK(63)
> > +#define S32_SCMI_CLK_EDMA_AHB S32_SCMI_CLK(64)
> > +/* ADC */
> > +#define S32_SCMI_CLK_SAR_ADC_BUS S32_SCMI_CLK(65)
> > +/* CMU */
> > +#define S32_SCMI_CLK_CMU_MODULE S32_SCMI_CLK(66)
> > +#define S32_SCMI_CLK_CMU_REG S32_SCMI_CLK(67)
> > +/* TMU */
> > +#define S32_SCMI_CLK_TMU_MODULE S32_SCMI_CLK(68)
> > +#define S32_SCMI_CLK_TMU_REG S32_SCMI_CLK(69)
> > +/* FlexRay */
> > +#define S32_SCMI_CLK_FR_REG S32_SCMI_CLK(70)
> > +#define S32_SCMI_CLK_FR_PE S32_SCMI_CLK(71)
> > +/* WKPU */
> > +#define S32_SCMI_CLK_WKPU_MODULE S32_SCMI_CLK(72)
> > +#define S32_SCMI_CLK_WKPU_REG S32_SCMI_CLK(73)
> > +/* SRC */
> > +#define S32_SCMI_CLK_SRC_MODULE S32_SCMI_CLK(74)
> > +#define S32_SCMI_CLK_SRC_REG S32_SCMI_CLK(75)
> > +/* SRC-TOP */
> > +#define S32_SCMI_CLK_SRC_TOP_MODULE S32_SCMI_CLK(76)
> > +#define S32_SCMI_CLK_SRC_TOP_REG S32_SCMI_CLK(77)
> > +/* CTU */
> > +#define S32_SCMI_CLK_CTU_MODULE S32_SCMI_CLK(78)
> > +#define S32_SCMI_CLK_CTU_CTU S32_SCMI_CLK(79)
> > +/* DBG */
> > +#define S32_SCMI_CLK_DBG_SYS4 S32_SCMI_CLK(80)
> > +#define S32_SCMI_CLK_DBG_SYS2 S32_SCMI_CLK(81)
> > +/* Cortex-M7 */
> > +#define S32_SCMI_CLK_M7_CORE S32_SCMI_CLK(82)
> > +/* DMAMUX */
> > +#define S32_SCMI_CLK_DMAMUX_MODULE S32_SCMI_CLK(83)
> > +#define S32_SCMI_CLK_DMAMUX_REG S32_SCMI_CLK(84)
> > +/* GIC */
> > +#define S32_SCMI_CLK_GIC_MODULE S32_SCMI_CLK(85)
> > +/* MSCM */
> > +#define S32_SCMI_CLK_MSCM_MODULE S32_SCMI_CLK(86)
> > +#define S32_SCMI_CLK_MSCM_REG S32_SCMI_CLK(87)
> > +/* SEMA42 */
> > +#define S32_SCMI_CLK_SEMA42_MODULE S32_SCMI_CLK(88)
> > +#define S32_SCMI_CLK_SEMA42_REG S32_SCMI_CLK(89)
> > +/* XRDC */
> > +#define S32_SCMI_CLK_XRDC_MODULE S32_SCMI_CLK(90)
> > +#define S32_SCMI_CLK_XRDC_REG S32_SCMI_CLK(91)
> > +/* CLKOUT */
> > +#define S32_SCMI_CLK_CLKOUT_0 S32_SCMI_CLK(92)
> > +#define S32_SCMI_CLK_CLKOUT_1 S32_SCMI_CLK(93)
> > +
> > +#define S32_SCMI_PLAT_CLK_BASE_ID S32_SCMI_CLK(94)
> > +
> > +#define S32_SCMI_CLK_MAX_ID S32_PLAT_SCMI_CLK(32)
> > +
> > +#endif
>
> Regards,
> Ghennadi
>
More information about the linux-arm-kernel
mailing list