[PATCH v2] arm64: dts: ti: beagleplay: Fix Ethernet PHY RESET GPIOs

[Roger Quadros]

The RESET GPIO pinmux should be part of MDIO bus node
so that they can be in the right state before the PHY
can be probed via MDIO bus scan.

The GPIO pin should be setup with PIN_INPUT so that
input circuitry is enabled in case software wants to
check pin status. Without this, incorrect status is shown
in /sys/kernel/debug/gpio.

Add GPIO reset for the Gigabit Ethernet PHY. As per
RTL8211F datasheet, reset assert width is 10ms and
PHY registers can be access accessed after 50ms of
reset deassert.

Fixes: f5a731f0787f ("arm64: dts: ti: Add k3-am625-beagleplay")
Signed-off-by: Roger Quadros <rogerq at kernel.org>
---
Changes in v2:
- Fix Subject to "arm64"
- Enable PIN_INPUT for SPE_RESET to fix GPIO status.
- Add Fixes tag.
- Link to v1: https://lore.kernel.org/r/20240229-b4-for-v6-9-am65-beagleplay-ethernet-reset-v1-1-b3e4b33378bd@kernel.org
---
 arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
index a34e0df2ab86..8ab838f1697c 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
@@ -292,6 +292,8 @@ mdio0_pins_default: mdio0-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
 			AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
+			AM62X_IOPAD(0x003c, PIN_INPUT, 7) /* (M25) GPMC0_AD0.GPIO0_15 */
+			AM62X_IOPAD(0x018c, PIN_INPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
 		>;
 	};
 
@@ -383,7 +385,6 @@ AM62X_IOPAD(0x017c, PIN_INPUT, 1) /* (AD22) RGMII2_RX_CTL.RMII2_RX_ER */
 			AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18) RGMII2_TD0.RMII2_TXD0 */
 			AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18) RGMII2_TD1.RMII2_TXD1 */
 			AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19) RGMII2_TX_CTL.RMII2_TX_EN */
-			AM62X_IOPAD(0x018c, PIN_OUTPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
 			AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22) RGMII2_RD3.GPIO1_6 */
 			AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18) EXT_REFCLK1.CLKOUT0 */
 		>;
@@ -597,6 +598,9 @@ &cpsw3g_mdio {
 
 	cpsw3g_phy0: ethernet-phy at 0 {
 		reg = <0>;
+		reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <50000>;
 	};
 
 	cpsw3g_phy1: ethernet-phy at 1 {
@@ -615,7 +619,7 @@ &main_gpio0 {
 		"USR0", "USR1", "USR2", "USR3", "", "", "USR4",	/* 3-9 */
 		"EEPROM_WP",					/* 10 */
 		"CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2",	/* 11-12 */
-		"CC1352P7_BOOT", "CC1352P7_RSTN", "", "", "",	/* 13-17 */
+		"CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "",	/* 13-17 */
 		"USR_BUTTON", "", "", "", "", "", "", "", "",	/* 18-26 */
 		"", "", "", "", "", "", "", "", "", "HDMI_INT",	/* 27-36 */
 		"", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */

---
base-commit: bbef42084cc170cbfc035bf784f2ff055c939d7e
change-id: 20240229-b4-for-v6-9-am65-beagleplay-ethernet-reset-098f274fbf15

Best regards,
-- 
Roger Quadros <rogerq at kernel.org>