[PATCH] ARM: dts: aspeed: asus: Add ASUS X4TF BMC
Kelly Hung(洪嘉莉)
Kelly_Hung at asus.com
Mon Mar 4 19:52:14 PST 2024
Hi, Krzysztof,
Please see my response below.
Thanks a log.
Best Regards
Kelly
-----Original Message-----
From: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
Sent: Tuesday, January 30, 2024 6:39 PM
To: Kelly Hung <ppighouse at gmail.com>; robh+dt at kernel.org
Cc: krzysztof.kozlowski+dt at linaro.org; conor+dt at kernel.org; joel at jms.id.au; andrew at codeconstruct.com.au; devicetree at vger.kernel.org; linux-arm-kernel at lists.infradead.org; linux-aspeed at lists.ozlabs.org; linux-kernel at vger.kernel.org; Kelly Hung(洪嘉莉) <Kelly_Hung at asus.com>
Subject: Re: [PATCH] ARM: dts: aspeed: asus: Add ASUS X4TF BMC
External email : Ensure your email is secure before opening links and attachments.
On 30/01/2024 09:56, Kelly Hung wrote:
> From: kelly1732000 <Kelly_Hung at asus.com>
>
> This initial device-tree provides the necessary configuration for
> basic BMC functionality and work on ASUS X4TF production.
>
> Signed-off-by: kelly1732000 <Kelly_Hung at asus.com>
> ---
> .../boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts | 828
> ++++++++++++++++++
> 1 file changed, 828 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
It's impossible to test this file. You miss Makefile.
Kelly: I've add aspeed-bmc-asus-x4tf.dtb in Makefle.
>
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
> b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
> new file mode 100644
> index 000000000000..723bbb33137f
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
> @@ -0,0 +1,828 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later // Copyright 2023 ASUS
> +Corp.
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h> #include
> +<dt-bindings/i2c/i2c.h>
> +
> +
> +/ {
> + model = "ASUS-X4TF";
> + compatible = "asus,x4tf", "aspeed,ast2600";
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200n8 earlycon";
earlycon is a debugging feature, not mainline. Also, move console to stdout-path, so entire bootargs can be dropped.
Kelly: I've moved "bootargs" into "stdout-path" and resend my patch.
> + };
> +
> + memory at 80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x40000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + gfx_memory: framebuffer {
> + size = <0x01000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> +
> + video_engine_memory: video {
> + size = <0x04000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> +
> + rvas_memory: rvas {
> + size = <0x04000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> +
> + bmc_dev_memory: bmc_dev_memory {
No underscores in node names. This applies everywhere.
Kelly: Yes, thanks for reminding, I've removed it and resent my patch.
> + size = <0x00100000>;
> + alignment = <0x00100000>;
> + compatible = "shared-dma-pool";
> + no-map;
> + };
> +
> + pci_msi_memory: pci_msi_memory {
> + no-map;
> + reg = <0x9e770000 0x100>;
> + compatible = "shared-dma-pool";
> + };
> + /* 1GB memory */
> + vga_memory: region at bf000000 {
> + no-map;
> + compatible = "shared-dma-pool";
> + reg = <0xbf000000 0x01000000>; /* 16M */
> + };
> + ssp_memory: ssp_memory {
> + size = <0x02000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + no-map;
> + };
> + };
> +
> + vcc_sdhci0: regulator-vcc-sdhci0 {
> + compatible = "regulator-fixed";
> + status = "disabled";
Why? It makes it entirely pointless.
Kelly: I've removed it and loaded into our X4TF platform and it boot into BMC console. I have resent my patch.
> + regulator-name = "SDHCI0 Vcc";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + vccq_sdhci0: regulator-vccq-sdhci0 {
> + compatible = "regulator-gpio";
> + status = "disabled";
Pointless node.
Kelly: I've removed it and loaded into our X4TF platform and it boot into BMC console. I have resent my patch.
> + regulator-name = "SDHCI0 VccQ";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
> + gpios-states = <1>;
> + states = <3300000 1>,
> + <1800000 0>;
> + };
> +
> + vcc_sdhci1: regulator-vcc-sdhci1 {
> + compatible = "regulator-fixed";
> + status = "disabled";
Pointless node.
Kelly: I've removed it and loaded into our X4TF platform and it boot into BMC console. I have resent my patch.
> + regulator-name = "SDHCI1 Vcc";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + vccq_sdhci1: regulator-vccq-sdhci1 {
> + compatible = "regulator-gpio";
> + status = "disabled";
Pointless node.
Kelly: I've removed it and loaded into our X4TF platform and it boot into BMC console. I have resent my patch.
> + regulator-name = "SDHCI1 VccQ";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
> + gpios-states = <1>;
> + states = <3300000 1>,
> + <1800000 0>;
> + };
Missing blank line.
Kelly: I've review our dts and add blank line or remove redundant blank lines.
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
> + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
> + <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
> + <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
> + };
> +> + video-engine at 1e700000 {
Wrong placement. Also tools would tell you that.
It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
Kelly: I've checked our dts, removed unnecessary parts and run the DTS check script.
> + compatible = "aspeed,ast2600-video-engine";
> + reg = <0x1e700000 0x20000>;
> + clocks = <&syscon ASPEED_CLK_GATE_VCLK>, <&syscon ASPEED_CLK_GATE_ECLK>;
> + clock-names = "vclk", "eclk";
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + memory-region = <&video_engine_memory>;
> + //resets = <&syscon ASPEED_RESET_VIDEO>;
Dead code.
Kelly: I have removed this part and resent the patch.
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + heartbeat {
It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
Kelly: I added led- for all LED configurations. Heartbeat will be led-heartbeat.
> + gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "heartbeat";
> + };
> + uid_led {
It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
Kelly: I added led- for all LED configurations.
> + gpios = <&gpio0 ASPEED_GPIO(P, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
> + default-state = "off";
> + };
Missing blank line, everywhere.
Kelly: I've review our dts and add blank line or remove redundant blank lines.
> + status_Y {
> + gpios = <&gpio1 ASPEED_GPIO(B, 1) GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + };
> + sys_boot_status {
> + gpios = <&gpio1 ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + };
> + };
> + spigpio {
It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
> + status = "okay";
Why?
Kelly: I've removed spigpio and tested on our X4TF platform and it boots to the BMC console. I've resent our new patch.
> + compatible = "spi-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> + mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
> + miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
> + num-chipselects = <1>;
> + cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
> + };
> +
Redundant blank line.
Kelly: I've review our dts and add blank line or remove redundant blank lines.
> +};
> +
> +&adc0 {
> + vref = <2500>;
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
> + &pinctrl_adc2_default &pinctrl_adc3_default
> + &pinctrl_adc4_default &pinctrl_adc5_default
> + &pinctrl_adc6_default &pinctrl_adc7_default>; };
> +
> +&adc1 {
> + vref = <2500>;
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
> + &pinctrl_adc10_default &pinctrl_adc11_default
> + &pinctrl_adc12_default &pinctrl_adc13_default
> + &pinctrl_adc14_default &pinctrl_adc15_default>; };
> +
> +&peci0 {
> + status = "okay";
> +};
> +
> +&lpc_snoop {
> + snoop-ports = <0x80>;
> + status = "okay";
> +};
> +
> +
Redundant blank line. Clean this code before sending upstream from such trivialities.
Kelly: I've review our dts and add blank line or remove redundant blank lines.
> +&mdio0 {
> + status = "disabled";
> +};
> +
> +
> +&mdio1 {
> + status = "disabled";
> +};
> +
> +&mdio2 {
> + status = "okay";
> +
> + ethphy2: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio3 {
> + status = "okay";
> +
> + ethphy3: ethernet-phy at 0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mac0 {
> + status = "disabled";
> +};
> +
> +&mac1 {
> + status = "disabled";
> +};
> +
> +//for X4TF
> +&mac2 {
> + status = "okay";
> + phy-mode = "rmii";
> + #phy-handle = <ðphy2>;
> + use-ncsi;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii3_default>; };
> +
> +
Ditto
Kelly: I've review our dts and add blank line or remove redundant blank lines.
> +&mac3 {
> + status = "okay";
> + phy-mode = "rmii";
> + #phy-handle = <ðphy3>;
> + use-ncsi;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii4_default>; };
> +
> +
Ditto
Kelly: I've review our dts and add blank line or remove redundant blank lines.
> +&syscon {
> + uart-clock-high-speed;
That's a syscon property?
It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
Kelly: I've removed syscon and tested on our X4TF platform and it boots to the BMC console. I've resent our new patch.
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "disabled";
> +};
> +
> +&fmc {
> + status = "okay";
> + flash at 0 {
> + status = "okay";
Drop. Everywhere where it is not needed.
Kelly: I've adjusted fmc config and resent the patch.
> + m25p,fast-read;
> + label = "bmc-spi";
> + spi-max-frequency = <50000000>;
> + spi-bus-width = <1>;
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + bmc at 0 {
> + label = "bmc";
> + reg = <0x0 0x4000000>;
> + };
> + u-boot at 0 {
> + label = "u-boot";
> + reg = <0x0 0x200000>;
> + };
> + u-boot-env at 1f0000 {
> + label = "u-boot-env";
> + reg = <0x1f0000 0x10000>;
> + };
> + kernel at 200000 {
> + label = "kernel";
> + reg = <0x200000 0xc00000>;
> + };
> + rofs at a00000 {
> + label = "rofs";
> + reg = <0xa00000 0x2a00000>;
> + };
> + rwfs at 2a00000 {
> + label = "rwfs";
> + reg = <0x2a00000 0x43f0000>;
> + };
> + };
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_default>;
> +
> + flash at 0 {
> + status = "okay";
> + w25q256,fast-read;
> + label = "bios-spi";
> + spi-max-frequency = <50000000>;
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + biosfullimg at 0 {
> + reg = <0x0 0x2000000>; // 32768 *1024 = 0x2000000, 32 MB
> + label = "biosfullimg";
> + };
> + };
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> + tmp75 at 48 {
Node names should be generic. See also an explanation and list of examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "ti,tmp75";
> + reg = <0x48>;
> + };
> + tmp75 at 49 {
Node names should be generic. See also an explanation and list of examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
I am going to skip the rest. Please fix all the trivialities and test your patches with tools.
Kelly: I have renamed tmp75 as temperature-sensor.
I've checked our dts, removed unnecessary parts and run the DTS check script.
Best regards,
Krzysztof
<p></p>
===================================================================================================================================
This email and any attachments to it contain confidential information and are intended solely for the use of the individual to whom it is addressed. If you are not the intended recipient or receive it accidentally, please immediately notify the sender by e-mail and delete the message and any attachments from your computer system, and destroy all hard copies. Please be advised that any unauthorized disclosure, copying, distribution or any action taken or omitted in reliance on this, is illegal and prohibited. Any views or opinions expressed are solely those of the author and do not represent those of ASUSTeK.
For pricing information, ASUS is only entitled to set a recommendation resale price. All customers are free to set their own price as they wish.
===================================================================================================================================
More information about the linux-arm-kernel
mailing list