[PATCH v2 2/2] arm64: dts: rockchip: Add Xunlong Orange Pi 3B
Jonas Karlman
jonas at kwiboo.se
Wed Jun 26 16:03:12 PDT 2024
The Xunlong Orange Pi 3B is a single-board computer based on the
Rockchip RK3566 SoC.
Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
---
v2:
- Add DT for v2.1 hw revision, rename initial DT to v1.1:
- Ethernet phy io voltage: 3v3 (v1.1) / 1v8 (v2.1)
- Etherent reset gpios: GPIO3_C2 (v1.1) / GPIO4_C4 (v2.1)
- WiFi/BT: CDW-20U5622 (v1.1) / AP6256 (v2.1)
- Rename led node and move led pinctrl props
- Use regulator-.* nodename for fixed regulators
- Drop rockchip,mic-in-differential prop
- Add cap-mmc-highspeed to sdhci node
- Add no-mmc and no-sd to sdmmc1 node
Following issue is reported by dtbs_check and is fixed by series at [1]:
pmic at 20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks'
do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
[1] https://lore.kernel.org/all/20240622-rk809-fixes-v2-0-c0db420d3639@collabora.com/
---
arch/arm64/boot/dts/rockchip/Makefile | 2 +
.../dts/rockchip/rk3566-orangepi-3b-v1.1.dts | 29 +
.../dts/rockchip/rk3566-orangepi-3b-v2.1.dts | 70 ++
.../boot/dts/rockchip/rk3566-orangepi-3b.dtsi | 678 ++++++++++++++++++
4 files changed, 779 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ae0ae02f51e9..df5a74c407f4 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -81,6 +81,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353ps.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353v.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353vs.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-orangepi-3b-v1.1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-orangepi-3b-v2.1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinetab2-v0.1.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
new file mode 100644
index 000000000000..074e93bd4b85
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-orangepi-3b.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 3B v1.1";
+ compatible = "xunlong,orangepi-3b-v1.1", "xunlong,orangepi-3b", "rockchip,rk3566";
+};
+
+&pmu_io_domains {
+ vccio5-supply = <&vcc_3v3>;
+};
+
+&gmac1 {
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
new file mode 100644
index 000000000000..d894bff41e61
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-orangepi-3b.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 3B v2.1";
+ compatible = "xunlong,orangepi-3b-v2.1", "xunlong,orangepi-3b", "rockchip,rk3566";
+
+ vccio_phy1: regulator-1v8-vccio-phy {
+ compatible = "regulator-fixed";
+ regulator-name = "vccio_phy1";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ };
+};
+
+&pmu_io_domains {
+ vccio5-supply = <&vccio_phy1>;
+};
+
+&gmac1 {
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&sdmmc1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ brcmf: wifi at 1 {
+ compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD6 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_wake_host_h>;
+ };
+};
+
+&uart1 {
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&rk809 1>;
+ clock-names = "lpo";
+ interrupt-parent = <&gpio2>;
+ interrupts = <RK_PC0 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wakeup";
+ device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_reg_on_h &bt_wake_host_h &host_wake_bt_h>;
+ vbat-supply = <&vcc_3v3>;
+ vddio-supply = <&vcc_1v8>;
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
new file mode 100644
index 000000000000..d539570f531e
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
@@ -0,0 +1,678 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 3B";
+ compatible = "xunlong,orangepi-3b", "rockchip,rk3566";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc0;
+ mmc2 = &sdmmc1;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led>;
+
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vcc3v3_pcie30: regulator-3v3-vcc-pcie30 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie20_pwren>;
+ regulator-name = "vcc3v3_pcie30";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc3v3_sys: regulator-3v3-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_sys: regulator-5v0-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_usb_host: regulator-5v0-vcc-usb-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren_h>;
+ regulator-name = "vcc5v0_usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb_otg: regulator-5v0-vcc-usb-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_otg_pwren_h>;
+ regulator-name = "vcc5v0_usb_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_reg_on_h>;
+ post-power-on-delay-ms = <200>;
+ power-off-delay-us = <5000000>;
+ reset-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+ clock_in_out = "input";
+ phy-mode = "rgmii-id";
+ phy-supply = <&vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m0_miim
+ &gmac1m0_tx_bus2
+ &gmac1m0_rx_bus2
+ &gmac1m0_rgmii_clk
+ &gmac1m0_rgmii_bus
+ &gmac1m0_clkinout>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk809: pmic at 20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-names = "mclk";
+ clock-output-names = "rk809-clkout1", "rk809-clkout2";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+ #sound-dai-cells = <0>;
+ system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu: regulator at 40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <830000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie20_pins>;
+ reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie30>;
+ status = "okay";
+};
+
+&pinctrl {
+ bluetooth {
+ bt_reg_on_h: bt-reg-on-h {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_wake_host_h: bt-wake-host-h {
+ rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ host_wake_bt_h: host-wake-bt-h {
+ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ work_led: work-led {
+ rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie20_pins: pcie20-pins {
+ rockchip,pins =
+ <1 RK_PB0 4 &pcfg_pull_none>,
+ <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>,
+ <1 RK_PB1 4 &pcfg_pull_none>;
+ };
+
+ pcie20_pwren: pcie20-pwren {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ usb_host_pwren_h: usb-host-pwren-h {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_otg_pwren_h: usb-otg-pwren-h {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_reg_on_h: wifi-reg-on-h {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wifi_wake_host_h: wifi-wake-host-h {
+ rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc_3v3>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ no-mmc;
+ no-sd;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_clk &sdmmc1_cmd>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sfc {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <104000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb_otg>;
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint at ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.45.2
More information about the linux-arm-kernel
mailing list