[PATCH RFC v3 3/6] dt-bindings: phy: cp110-utmi-phy: add compatible string for armada-38x

[Josua Mayer]

Am 21.07.24 um 11:31 schrieb Krzysztof Kozlowski:
> On 20/07/2024 16:19, Josua Mayer wrote:
>> Armada 38x USB-2.0 PHYs are similar to Armada 8K (CP110) and can be
>> supported by the same driver with small differences.
>>
>> Add new compatible string for armada-38x variant of utmi phy.
>> Then add descriptions and names for two additional register definitions
>> that may be specified instead of a syscon phandle.
>>
>> Signed-off-by: Josua Mayer <josua at solid-run.com>
>> ---
>>  .../phy/marvell,armada-cp110-utmi-phy.yaml         | 34 ++++++++++++++++++----
>>  1 file changed, 29 insertions(+), 5 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml b/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml
>> index 9ce7b4c6d208..246e48d51755 100644
>> --- a/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml
>> +++ b/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml
>> @@ -23,12 +23,36 @@ description:
>>    UTMI PHY1  --------\
>>                        1.H----- USB HOST1
>>  
>> +  On Armada 380 there is an additional USB-2.0-only controller,
>> +  and an additional UTMI PHY respectively.
>> +  The USB device controller can only be connected to a single UTMI PHY port,
>> +  either UTMI PHY0 or UTMI PHY2.
>> +
>> +
>> +
> One blank line is enough.
Ack.
>
>>  properties:
>>    compatible:
>> -    const: marvell,cp110-utmi-phy
>> +    enum:
>> +      - marvell,a38x-utmi-phy
>> +      - marvell,cp110-utmi-phy
>>  
>>    reg:
>> -    maxItems: 1
>> +    anyOf:
> That's oneOf.

Acknowledged, thanks!

Today oneOf seems correct to me, too.

>
>> +      - items:
>> +          - description: UTMI registers
>> +      - items:
>> +          - description: UTMI registers
>> +          - description: USB config register
>> +          - description: UTMI config registers
>> +
>> +  reg-names:
>> +    anyOf:
> oneOf
Ack.
>
>> +      - items:
>> +          - const: utmi
>> +      - items:
>> +          - const: utmi
>> +          - const: usb-cfg
>> +          - const: utmi-cfg
>>  
>>    "#address-cells":
>>      const: 1
>> @@ -38,13 +62,14 @@ properties:
>>  
>>    marvell,system-controller:
>>      description:
>> -      Phandle to the system controller node
>> +      Phandle to the system controller node.
>> +      Optional when usb-cfg and utmi-cfg regs are given.
>>      $ref: /schemas/types.yaml#/definitions/phandle
>>  
>>  # Required child nodes:
>>  
>>  patternProperties:
>> -  "^usb-phy@[0|1]$":
>> +  "^usb-phy@[0|1|2]$":
> [0-2]
Ack.
>
>>      type: object
>>      description:
>>        Each UTMI PHY port must be represented as a sub-node.
>> @@ -68,7 +93,6 @@ required:
>>    - reg
>>    - "#address-cells"
>>    - "#size-cells"
>> -  - marvell,system-controller
> you miss here allOf:if:then: narrowing and marvell,system-controller per
> each variant.
Correct.
I will learn how to do that, and included it a non-rfc version.


Thanks!

sincerely
Josua Mayer