[PATCH 2/2] arm64: dts: rockchip: Add support for rk3588 GenBook
Andy Yan
andyshrk at 163.com
Sat Jul 20 03:45:21 PDT 2024
Hello Dragan，
在 2024-07-20 18:21:37，"Dragan Simic" <dsimic at manjaro.org> 写道：
>Hello Andy,
>
>I forgot to note something in my previous response, so please
>see an additional note below.
>
>On 2024-07-16 15:50, Dragan Simic wrote:
>> On 2024-07-16 12:07, Andy Yan wrote:
>>> 在 2024-07-15 22:47:04，"Dragan Simic" <dsimic at manjaro.org> 写道：
>>>> On 2024-07-15 12:44, Andy Yan wrote:
>>>>> At 2024-07-14 23:27:54, "Dragan Simic" <dsimic at manjaro.org> wrote:
>>>>>> Please see a few comments below.
>>>>>>
>>>>>> On 2024-07-14 13:28, Andy Yan wrote:
>>>>>>> Cool Pi GenBook works as a mother board connect with CM5 [0].
>>>>>>
>>>>>> s/mother board/carrier board/
>>>>>
>>>>> This can be changed to carrier board in next version。
>>>>>
>>>>>> s/CM5/GenM5/
>>>>>
>>>>> In fact, the SOM is called CM5 always[0]， even this laptop was
>>>>> called cm5 laptop from the
>>>>> very beginning of the design。
>>>>> They just gave it a new name GenBook when it comes to crowdsupply.
>>>>>
>>>>> The dtsi for CM5 is aready landing upstream，I inclulde it in the
>>>>> current genbook dts。
>>>>>
>>>>> [0]https://forum.cool-pi.com/topic/98/cool-pi-5-compute-module-minipc-carrier-board-spec
>>>>
>>>> Ah, that's quite interesting, it was probably renamed for marketing
>>>> purposes. Thanks for the clarification.
>>>>
>>>> To add to the confusion, none of "GenBook", "CM5" or "GenM5" appear
>>>> on the labels found on the actual PCBs. [1] Instead, there are only
>>>> some rather generic terms.
>>>
>>> So we can keep the name as it is now ？
>>
>> As far as I'm concerned, yes. Everything points to "CoolPi CM5"
>> and "CoolPi GenBook" being the rigth names in the upstream kernel
>> for the SoM and the carrier board, respectively.
>>
>> However, please see another comment below.
>>
>>>> [1]
>>>> https://www.crowdsupply.com/img/6185/60c35852-7a58-4b6f-80fc-af3a0e3d6185/genbook-rk3588-main-board-close-up_jpg_gallery-lg.jpg
>>>>
>>>>>>> Specification:
>>>>>>> - Rockchip RK3588
>>>>>>> - LPDDR5X 8/32 GB
>>>>>>> - eMMC 64 GB
>>>>>>> - HDMI Type A out x 1
>>>>>>> - USB 3.0 Host x 1
>>>>>>> - USB-C 3.0 with DisplayPort AltMode
>>>>>>> - PCIE M.2 E Key for RTL8852BE Wireless connection
>>>>>>> - PCIE M.2 M Key for NVME connection
>>>>>>> - eDP panel with 1920x1080
>>>>>>>
>>>>>>> This patch add basic support to bringup eMMC/USB HOST/WiFi
>>>>>>> and can also drive a HDMI output with out of tree hdmi patches.
>>>>>>>
>>>>>>> [0]
>>>>>>> https://www.crowdsupply.com/shenzhen-tianmao-technology-co-ltd/genbook-rk3588
>>>>>>>
>>>>>>> Signed-off-by: Andy Yan <andyshrk at 163.com>
>>>>>>> ---
>>>>>>>
>>>>>>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
>>>>>>> .../dts/rockchip/rk3588-coolpi-genbook.dts | 296
>>>>>>> ++++++++++++++++++
>>>>>>> 2 files changed, 297 insertions(+)
>>>>>>> create mode 100644
>>>>>>> arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>>>>>>
>>>>>> It would be better to split this into two files: a dtsi for the
>>>>>> GenM5
>>>>>> system
>>>>>> on module, and a dts for the GenBook carrier board. That way, the
>>>>>> dts(i) files
>>>>>> would describe the actual hardware better.
>>>>>>
>>>>>>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
>>>>>>> b/arch/arm64/boot/dts/rockchip/Makefile
>>>>>>> index 8fa469db400c..0fad54939bbd 100644
>>>>>>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>>>>>>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>>>>>>> @@ -122,6 +122,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) +=
>>>>>>> rk3568-wolfvision-pf5-display-vz.dtbo
>>>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) +=
>>>>>>> rk3568-wolfvision-pf5-io-expander.dtbo
>>>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-armsom-sige7.dtb
>>>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-coolpi-cm5-evb.dtb
>>>>>>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-coolpi-genbook.dtb
>>>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
>>>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-wifi.dtbo
>>>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb
>>>>>>> diff --git
>>>>>>> a/arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>>>>>>> b/arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>
>The new device dts file should be named rk3588-coolpi-cm5-genbook.dts
>instead of rk3588-coolpi-genbook.dts, because that would:
Okay，will be done in V2.
Thanks
>
> (a) follow the "dependency graph" naming scheme, and
> (b) make the naming scheme future-proof for some other SoM that
> could possibly be made available for the GenBook in the
> future, for which the new device dts file would be named
> rk3588-coolpi-XYZ-genbook.dts.
>
>>>>>>> new file mode 100644
>>>>>>> index 000000000000..28357c6f05fb
>>>>>>> --- /dev/null
>>>>>>> +++ b/arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>>>>>>> @@ -0,0 +1,296 @@
>>>>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>>>>>> +/*
>>>>>>> + * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
>>>>>>> + *
>>>>>>> + */
>>>>>>> +
>>>>>>> +/dts-v1/;
>>>>>>> +
>>>>>>> +#include <dt-bindings/leds/common.h>
>>>>>>> +#include "rk3588-coolpi-cm5.dtsi"
>>>>>>> +
>>>>>>> +/ {
>>>>>>> + model = "RK3588 CoolPi GenBook";
>>
>> It would be better to omit "RK3588" from the model name and use
>> "CM5" instead, because that more precisely reflects the "dependency
>> graph", so to speak. Thus, I'd suggest that "CoolPi CM5 GenBook"
>> is used as the model name.
>>
>> Technically, "CoolPi CM5 on GenBook carrier board" would be a more
>> correct model name, so that's another option, but the above-proposed
>> "CoolPi CM5 GenBook" sounds more like a finished product/device
>> than just some carrier board with an SoM.
>>
>>>>>>> + compatible = "coolpi,genbook", "coolpi,pi-cm5",
>>>>>>> "rockchip,rk3588";
>>>>>>> +
>>>>>>> + backlight: backlight {
>>>>>>> + compatible = "pwm-backlight";
>>>>>>> + enable-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
>>>>>>> + pinctrl-names = "default";
>>>>>>> + pinctrl-0 = <&bl_en>;
>>>>>>> + power-supply = <&vcc12v_dcin>;
>>>>>>> + pwms = <&pwm6 0 25000 0>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + leds: leds {
>>>>>>> + compatible = "gpio-leds";
>>>>>>> +
>>>>>>> + heartbeat_led: led-0 {
>>>>>>> + color = <LED_COLOR_ID_GREEN>;
>>>>>>> + function = LED_FUNCTION_STATUS;
>>>>>>> + gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
>>>>>>> + linux,default-trigger = "heartbeat";
>>>>>>> + };
>>>>>>> +
>>>>>>> + wlan_led: led-1 {
>>>>>>> + color = <LED_COLOR_ID_GREEN>;
>>>>>>> + function = LED_FUNCTION_WLAN;
>>>>>>> + gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + charging_red: led-2 {
>>>>>>> + function = LED_FUNCTION_CHARGING;
>>>>>>> + color = <LED_COLOR_ID_RED>;
>>>>>>> + gpios = <&gpio3 RK_PD2 GPIO_ACTIVE_HIGH>;
>>>>>>> + };
>>>>>>> + };
>>>>>>> +
>>>>>>> + vcc12v_dcin: vcc12v-dcin-regulator {
>>>>>>> + compatible = "regulator-fixed";
>>>>>>> + regulator-name = "vcc12v_dcin";
>>>>>>> + regulator-always-on;
>>>>>>> + regulator-boot-on;
>>>>>>> + regulator-min-microvolt = <12000000>;
>>>>>>> + regulator-max-microvolt = <12000000>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + vcc_sys: vcc-sys-regulator {
>>>>>>> + compatible = "regulator-fixed";
>>>>>>> + regulator-name = "vcc_sys";
>>>>>>> + regulator-always-on;
>>>>>>> + regulator-boot-on;
>>>>>>> + regulator-min-microvolt = <7000000>;
>>>>>>> + regulator-max-microvolt = <7000000>;
>>>>>>> + vin-supply = <&vcc12v_dcin>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + vcc5v0_sys: vcc5v0-sys-regulator {
>>>>>>> + compatible = "regulator-fixed";
>>>>>>> + regulator-name = "vcc5v0_sys";
>>>>>>> + regulator-always-on;
>>>>>>> + regulator-boot-on;
>>>>>>> + regulator-min-microvolt = <7000000>;
>>>>>>> + regulator-max-microvolt = <7000000>;
>>>>>>> + vin-supply = <&vcc_sys>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + vcc3v3_sys: vcc3v3-sys-regulator {
>>>>>>> + compatible = "regulator-fixed";
>>>>>>> + regulator-name = "vcc3v3_sys";
>>>>>>> + regulator-always-on;
>>>>>>> + regulator-boot-on;
>>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>>> + vin-supply = <&vcc5v0_sys>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + vcc3v3_lcd: vcc3v3-lcd-regulator {
>>>>>>> + compatible = "regulator-fixed";
>>>>>>> + regulator-name = "vcc3v3_lcd";
>>>>>>> + enable-active-high;
>>>>>>> + gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
>>>>>>> + pinctrl-names = "default";
>>>>>>> + pinctrl-0 = <&lcdpwr_en>;
>>>>>>> + vin-supply = <&vcc3v3_sys>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + vcc5v0_usb: vcc5v0-usb-regulator {
>>>>>>> + compatible = "regulator-fixed";
>>>>>>> + regulator-name = "vcc5v0_usb";
>>>>>>> + regulator-boot-on;
>>>>>>> + regulator-always-on;
>>>>>>> + enable-active-high;
>>>>>>> + regulator-min-microvolt = <5000000>;
>>>>>>> + regulator-max-microvolt = <5000000>;
>>>>>>> + gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
>>>>>>> + pinctrl-names = "default";
>>>>>>> + pinctrl-0 = <&usb_pwren>;
>>>>>>> + vin-supply = <&vcc_sys>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + vcc5v0_usb_host0: vcc5v0_usb30_host: vcc5v0-usb-host-regulator {
>>>>>>> + compatible = "regulator-fixed";
>>>>>>> + regulator-name = "vcc5v0_host";
>>>>>>> + regulator-boot-on;
>>>>>>> + regulator-always-on;
>>>>>>> + enable-active-high;
>>>>>>> + regulator-min-microvolt = <5000000>;
>>>>>>> + regulator-max-microvolt = <5000000>;
>>>>>>> + gpio = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
>>>>>>> + pinctrl-names = "default";
>>>>>>> + pinctrl-0 = <&usb_host_pwren>;
>>>>>>> + vin-supply = <&vcc5v0_usb>;
>>>>>>> + };
>>>>>>> +};
>>>>>>> +
>>>>>>> +&gmac0 {
>>>>>>> + status = "disabled";
>>>>>>> +};
>>>>>>> +
>>>>>>> +/* M.2 E-Key */
>>>>>>> +&pcie2x1l0 {
>>>>>>> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
>>>>>>> + vpcie3v3-supply = <&vcc3v3_sys>;
>>>>>>> + pinctrl-names = "default";
>>>>>>> + pinctrl-0 = <&pcie_clkreq &pcie_wake &pcie_rst &wifi_pwron
>>>>>>> &bt_pwron>;
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&pcie2x1l2 {
>>>>>>> + status = "disabled";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&pcie30phy {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +/* M.2 M-Key ssd */
>>>>>>> +&pcie3x4 {
>>>>>>> + reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
>>>>>>> + vpcie3v3-supply = <&vcc3v3_sys>;
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&pinctrl {
>>>>>>> + lcd {
>>>>>>> + lcdpwr_en: lcdpwr-en {
>>>>>>> + rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + bl_en: bl-en {
>>>>>>> + rockchip,pins = <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
>>>>>>> + };
>>>>>>> + };
>>>>>>> +
>>>>>>> + usb {
>>>>>>> + usb_pwren: usb-pwren {
>>>>>>> + rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + usb_otg_pwren: usb-otg-pwren {
>>>>>>> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + usb_host_pwren: usb-host-pwren {
>>>>>>> + rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> + };
>>>>>>> +
>>>>>>> + wifi {
>>>>>>> + bt_pwron: bt-pwron {
>>>>>>> + rockchip,pins = <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + pcie_clkreq: pcie-clkreq {
>>>>>>> + rockchip,pins = <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + pcie_rst: pcie-rst {
>>>>>>> + rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + wifi_pwron: wifi-pwron {
>>>>>>> + rockchip,pins = <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + pcie_wake: pcie-wake {
>>>>>>> + rockchip,pins = <4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>>>> + };
>>>>>>> + };
>>>>>>> +};
>>>>>>> +
>>>>>>> +&pwm6 {
>>>>>>> + pinctrl-0 = <&pwm6m1_pins>;
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&sdmmc {
>>>>>>> + status = "disabled";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&sfc {
>>>>>>> + pinctrl-names = "default";
>>>>>>> + pinctrl-0 = <&fspim2_pins>;
>>>>>>> + status = "okay";
>>>>>>> +
>>>>>>> + flash at 0 {
>>>>>>> + compatible = "jedec,spi-nor";
>>>>>>> + reg = <0x0>;
>>>>>>> + spi-max-frequency = <100000000>;
>>>>>>> + spi-rx-bus-width = <4>;
>>>>>>> + spi-tx-bus-width = <1>;
>>>>>>> + };
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy0 {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy0_otg {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&usbdp_phy0 {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy1 {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy1_otg {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy2 {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy3 {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy2_host {
>>>>>>> + phy-supply = <&vcc5v0_usb_host0>;
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&u2phy3_host {
>>>>>>> + phy-supply = <&vcc5v0_usb>;
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&usbdp_phy1 {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +/* For Keypad */
>>>>>>> +&usb_host0_ehci {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&usb_host0_ohci {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +/* Type C port */
>>>>>>> +&usb_host0_xhci {
>>>>>>> + dr_mode = "peripheral";
>>>>>>> + maximum-speed = "high-speed";
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +/* connected to a HUB for camera and BT */
>>>>>>> +&usb_host1_ehci {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +&usb_host1_ohci {
>>>>>>> + status = "okay";
>>>>>>> +};
>>>>>>> +
>>>>>>> +/* USB A out */
>>>>>>> +&usb_host1_xhci {
>>>>>>> + dr_mode = "host";
>>>>>>> + status = "okay";
>>>>>>> +};
More information about the linux-arm-kernel
mailing list