[PATCH v2 2/3] Bluetooth: hci_uart: Add support for Amlogic HCI UART

[Yang Li]

Dear Krzysztof

Thanks for the review.

On 2024/7/18 19:43, Krzysztof Kozlowski wrote:
> On 18/07/2024 09:42, Yang Li via B4 Relay wrote:
>> From: Yang Li <yang.li at amlogic.com>
>>
>> This patch introduces support for Amlogic Bluetooth controller over
>> UART. In order to send the final firmware at full speed. It is a pretty
>> straight forward H4 driver with exception of actually having it's own
>> setup address configuration.
>>
> ...
>
>> +static int aml_parse_dt(struct aml_serdev *amldev)
>> +{
>> +     struct device *pdev = amldev->dev;
>> +
>> +     amldev->bt_en_gpio = devm_gpiod_get(pdev, "bt-enable",
>> +                                     GPIOD_OUT_LOW);
>> +     if (IS_ERR(amldev->bt_en_gpio)) {
>> +             dev_err(pdev, "Failed to acquire bt-enable gpios");
>> +             return PTR_ERR(amldev->bt_en_gpio);
>> +     }
>> +
>> +     if (device_property_read_string(pdev, "firmware-name",
>> +                                     &amldev->firmware_name)) {
>> +             dev_err(pdev, "Failed to acquire firmware path");
>> +             return -ENODEV;
>> +     }
>> +
>> +     amldev->bt_supply = devm_regulator_get(pdev, "bt");
>> +     if (IS_ERR(amldev->bt_supply)) {
>> +             dev_err(pdev, "Failed to acquire regulator");
>> +             return PTR_ERR(amldev->bt_supply);
>> +     }
>> +
>> +     amldev->lpo_clk = devm_clk_get(pdev, NULL);
>> +     if (IS_ERR(amldev->lpo_clk)) {
>> +             dev_err(pdev, "Failed to acquire clock source");
>> +             return PTR_ERR(amldev->lpo_clk);
>> +     }
>> +
>> +     /* get rf config parameter */
>> +     if (device_property_read_u32(pdev, "antenna-number",
>> +                             &amldev->ant_number)) {
>> +             dev_info(pdev, "No antenna-number, using default value");
>> +             amldev->ant_number = 1;
>> +     }
>> +
>> +     return 0;
>> +}
>> +
>> +static int aml_power_on(struct aml_serdev *amldev)
>> +{
>> +     int err;
>> +
>> +     if (!IS_ERR(amldev->bt_supply)) {
> How is IS_ERR possible?
Well, I got it.
>
>> +             err = regulator_enable(amldev->bt_supply);
>> +             if (err) {
>> +                     dev_err(amldev->dev, "Failed to enable regulator: (%d)", err);
>> +                     return err;
>> +             }
>> +     }
>> +
>> +     if (!IS_ERR(amldev->lpo_clk)) {
> How is IS_ERR possible?
I got it.
>
>> +             err = clk_prepare_enable(amldev->lpo_clk);
>> +             if (err) {
>> +                     dev_err(amldev->dev, "Failed to enable lpo clock: (%d)", err);
>> +                     return err;
>> +             }
>> +     }
>> +
>> +     if (!IS_ERR(amldev->bt_en_gpio))
> How is IS_ERR possible?
I got it.
>
>> +             gpiod_set_value_cansleep(amldev->bt_en_gpio, 1);
>> +
>> +     /* wait 100ms for bluetooth controller power on  */
>> +     msleep(100);
>> +     return 0;
>> +}
>
> Best regards,
> Krzysztof
>