[PATCH v5 27/27] ARM: dts: microchip: sam9x75_curiosity: add sam9x75 curiosity board
claudiu beznea
claudiu.beznea at tuxon.dev
Sun Jul 14 06:46:23 PDT 2024
Hi, Varshini,
On 03.07.2024 13:29, Varshini Rajendran wrote:
> Add device tree file for sam9x75 curiosity board.
>
> Signed-off-by: Varshini Rajendran <varshini.rajendran at microchip.com>
> ---
> Changes in v5:
> - Update commit message to match the directory structure.
> - Alphanumerically sorted Makefile entries.
> - Corrected VDDCore minimum voltage.
> - Enabled the i2s node.
> - Removed additional blank lines.
> - Enclosed each entry with separate <>.
> - Corrected pinctrl names to match Microchip convention.
> - Enabled slewrate in sdmmc node.
> - Corrected pinmux mask.
> - Added phandle to leds for ease of access with upcoming device entries.
> - Updated gpio pin number for red led.
> ---
> arch/arm/boot/dts/microchip/Makefile | 3 +
> .../dts/microchip/at91-sam9x75_curiosity.dts | 312 ++++++++++++++++++
> 2 files changed, 315 insertions(+)
> create mode 100644 arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
>
> diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile
> index 0c45c8d17468..470fe46433a9 100644
> --- a/arch/arm/boot/dts/microchip/Makefile
> +++ b/arch/arm/boot/dts/microchip/Makefile
> @@ -2,6 +2,7 @@
> # Enables support for device-tree overlays
> DTC_FLAGS_at91-sam9x60_curiosity := -@
> DTC_FLAGS_at91-sam9x60ek := -@
> +DTC_FLAGS_at91-sam9x75_curiosity := -@
> DTC_FLAGS_at91-sama5d27_som1_ek := -@
> DTC_FLAGS_at91-sama5d27_wlsom1_ek := -@
> DTC_FLAGS_at91-sama5d29_curiosity := -@
> @@ -60,6 +61,8 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
> dtb-$(CONFIG_SOC_SAM9X60) += \
> at91-sam9x60_curiosity.dtb \
> at91-sam9x60ek.dtb
> +dtb-$(CONFIG_SOC_SAM9X7) += \
> + at91-sam9x75_curiosity.dtb
> dtb-$(CONFIG_SOC_SAM_V7) += \
> at91-kizbox2-2.dtb \
> at91-kizbox3-hs.dtb \
> diff --git a/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
> new file mode 100644
> index 000000000000..4a4f14f13634
> --- /dev/null
> +++ b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
> @@ -0,0 +1,312 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * at91-sam9x75_curiosity.dts - Device Tree file for Microchip SAM9X75 Curiosity board
> + *
> + * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Varshini Rajendran <varshini.rajendran at microchip.com>
> + */
> +/dts-v1/;
> +#include "sam9x7.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Microchip SAM9X75 Curiosity";
> + compatible = "microchip,sam9x75-curiosity", "microchip,sam9x7", "atmel,at91sam9";
> +
> + aliases {
> + i2c0 = &i2c6;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_key_gpio_default>;
> +
> + button-user {
> + label = "USER";
> + gpios = <&pioC 9 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_0>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_red: led-red {
> + label = "red";
> + gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&pinctrl_red_led_gpio_default>;
> + };
> +
> + led_green: led-green {
> + label = "green";
> + gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&pinctrl_green_led_gpio_default>;
> + };
> +
> + led_blue: led-blue {
> + label = "blue";
> + gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&pinctrl_blue_led_gpio_default>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + memory at 20000000 {
> + reg = <0x20000000 0x10000000>;
> + device_type = "memory";
> + };
> +};
> +
> +&classd {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_classd_default>;
> + atmel,pwm-type = "diff";
> + atmel,non-overlap-time = <10>;
> + status = "okay";
> +};
> +
> +&dbgu {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_dbgu_default>;
> + status = "okay";
> +};
> +
> +&dma0 {
> + status = "okay";
> +};
> +
> +&flx6 {
> + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
> + status = "okay";
> +};
> +
> +&i2c6 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flx6_default>;
> + i2c-analog-filter;
> + i2c-digital-filter;
> + i2c-digital-filter-width-ns = <35>;
> + status = "okay";
> +
> + pmic at 5b {
> + compatible = "microchip,mcp16502";
> + reg = <0x5b>;
> +
> + regulators {
> + vdd_3v3: VDD_IO {
> + regulator-name = "VDD_IO";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-initial-mode = <2>;
> + regulator-allowed-modes = <2>, <4>;
> + regulator-always-on;
> +
> + regulator-state-standby {
> + regulator-on-in-suspend;
> + regulator-mode = <4>;
> + };
> +
> + regulator-state-mem {
> + regulator-mode = <4>;
> + };
> + };
> +
> + vddioddr: VDD_DDR {
> + regulator-name = "VDD_DDR";
> + regulator-min-microvolt = <1283000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-initial-mode = <2>;
> + regulator-allowed-modes = <2>, <4>;
> + regulator-always-on;
> +
> + regulator-state-standby {
> + regulator-on-in-suspend;
> + regulator-mode = <4>;
> + };
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-mode = <4>;
> + };
> + };
> +
> + vddcore: VDD_CORE {
> + regulator-name = "VDD_CORE";
> + regulator-min-microvolt = <1140000>;
> + regulator-max-microvolt = <1210000>;
> + regulator-initial-mode = <2>;
> + regulator-allowed-modes = <2>, <4>;
> + regulator-always-on;
> +
> + regulator-state-standby {
> + regulator-on-in-suspend;
> + regulator-mode = <4>;
> + };
> +
> + regulator-state-mem {
> + regulator-mode = <4>;
> + };
> + };
> +
> + vddcpu: VDD_OTHER {
> + regulator-name = "VDD_OTHER";
> + regulator-min-microvolt = <1700000>;
> + regulator-max-microvolt = <3600000>;
I haven't got any input on question asked in v4 on the regulator values.
Are the values from this version the right ones? Is this board supporting
DVFS or the label name is wrong or maybe the min-max range is still wrong?
> + regulator-initial-mode = <2>;
> + regulator-allowed-modes = <2>, <4>;
> + regulator-ramp-delay = <3125>;
> + regulator-always-on;
> +
> + regulator-state-standby {
> + regulator-on-in-suspend;
> + regulator-mode = <4>;
> + };
> +
> + regulator-state-mem {
> + regulator-mode = <4>;
> + };
> + };
> +
> + vldo1: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3700000>;
> + regulator-always-on;
> +
> + regulator-state-standby {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vldo2: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3700000>;
> +
> + regulator-state-standby {
> + regulator-on-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2s {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2s_default>;
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +
> +&main_xtal {
> + clock-frequency = <24000000>;
> +};
> +
> +&pinctrl {
> + classd {
> + pinctrl_classd_default: classd-default {
> + atmel,pins =
> + <AT91_PIOA 18 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>,
> + <AT91_PIOA 19 AT91_PERIPH_C AT91_PINCTRL_PULL_DOWN>;
> + };
> + };
> +
> + dbgu {
> + pinctrl_dbgu_default: dbgu-default {
> + atmel,pins = <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
> + <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + flexcom {
> + pinctrl_flx6_default: flx6-default {
> + atmel,pins =
> + <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
> + <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
> + };
> + };
> +
> + gpio-keys {
> + pinctrl_key_gpio_default: key-gpio-default {
> + atmel,pins = <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + i2s {
> + pinctrl_i2s_default: i2s-default {
> + atmel,pins =
> + <AT91_PIOB 26 AT91_PERIPH_D AT91_PINCTRL_NONE>, /* I2SCK */
> + <AT91_PIOB 15 AT91_PERIPH_D AT91_PINCTRL_NONE>, /* I2SWS */
> + <AT91_PIOB 16 AT91_PERIPH_D AT91_PINCTRL_NONE>, /* I2SDIN */
> + <AT91_PIOB 17 AT91_PERIPH_D AT91_PINCTRL_NONE>, /* I2SDOUT */
> + <AT91_PIOB 25 AT91_PERIPH_D AT91_PINCTRL_NONE>; /* I2SMCK */
> + };
> + };
> +
> + leds {
> + pinctrl_red_led_gpio_default: red-led-gpio-default {
> + atmel,pins = <AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + pinctrl_green_led_gpio_default: green-led-gpio-default {
> + atmel,pins = <AT91_PIOC 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + pinctrl_blue_led_gpio_default: blue-led-gpio-default {
> + atmel,pins = <AT91_PIOC 20 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
> + };
> + };
> +
> + sdmmc0 {
> + pinctrl_sdmmc0_default: sdmmc0-default {
> + atmel,pins =
> + <AT91_PIOA 2 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>, /* PA2 CK periph A with pullup */
> + <AT91_PIOA 1 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>, /* PA1 CMD periph A with pullup */
> + <AT91_PIOA 0 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>, /* PA0 DAT0 periph A */
> + <AT91_PIOA 3 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>, /* PA3 DAT1 periph A with pullup */
> + <AT91_PIOA 4 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>, /* PA4 DAT2 periph A with pullup */
> + <AT91_PIOA 5 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>; /* PA5 DAT3 periph A with pullup */
> + };
> + };
> +}; /* pinctrl */
> +
> +&rtt {
> + atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sdmmc0_default>;
> + cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + status = "okay";
> +};
> +
> +&slow_xtal {
> + clock-frequency = <32768>;
> +};
> +
> +&poweroff {
> + debounce-delay-us = <976>;
> + status = "okay";
> +
> + input at 0 {
> + reg = <0>;
> + };
> +};
> +
> +&trng {
> + status = "okay";
> +};
> +
> +&watchdog {
> + status = "okay";
> +};
More information about the linux-arm-kernel
mailing list