[PATCH v13 6/6] iommu/arm-smmu: add support for PRR bit setup
Bibek Kumar Patro
quic_bibekkum at quicinc.com
Tue Jul 9 12:42:39 PDT 2024
On 7/4/2024 9:28 PM, Rob Clark wrote:
> On Thu, Jul 4, 2024 at 7:46 AM Rob Clark <robdclark at gmail.com> wrote:
>>
>> On Wed, Jul 3, 2024 at 4:38 AM Bibek Kumar Patro
>> <quic_bibekkum at quicinc.com> wrote:
>>>
>>>
>>>
>>> On 7/2/2024 2:01 AM, Rob Clark wrote:
>>>> On Mon, Jul 1, 2024 at 4:01 AM Bibek Kumar Patro
>>>> <quic_bibekkum at quicinc.com> wrote:
>>>>>
>>>>>
>>>>>
>>>>> On 6/28/2024 9:14 PM, Rob Clark wrote:
>>>>>> On Fri, Jun 28, 2024 at 8:10 AM Bibek Kumar Patro
>>>>>> <quic_bibekkum at quicinc.com> wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> On 6/28/2024 7:47 PM, Rob Clark wrote:
>>>>>>>> On Fri, Jun 28, 2024 at 7:05 AM Bibek Kumar Patro
>>>>>>>> <quic_bibekkum at quicinc.com> wrote:
>>>>>>>>>
>>>>>>>>> Add an adreno-smmu-priv interface for drm/msm to call
>>>>>>>>> into arm-smmu-qcom and initiate the PRR bit setup or reset
>>>>>>>>> sequence as per request.
>>>>>>>>>
>>>>>>>>> This will be used by GPU to setup the PRR bit and related
>>>>>>>>> configuration registers through adreno-smmu private
>>>>>>>>> interface instead of directly poking the smmu hardware.
>>>>>>>>>
>>>>>>>>> Suggested-by: Rob Clark <robdclark at gmail.com>
>>>>>>>>> Signed-off-by: Bibek Kumar Patro <quic_bibekkum at quicinc.com>
>>>>>>>>> ---
>>>>>>>>> drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c | 23 ++++++++++++++++++++++
>>>>>>>>> drivers/iommu/arm/arm-smmu/arm-smmu.h | 2 ++
>>>>>>>>> include/linux/adreno-smmu-priv.h | 6 +++++-
>>>>>>>>> 3 files changed, 30 insertions(+), 1 deletion(-)
>>>>>>>>>
>>>>>>>>> diff --git a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
>>>>>>>>> index bd101a161d04..64571a1c47b8 100644
>>>>>>>>> --- a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
>>>>>>>>> +++ b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
>>>>>>>>> @@ -28,6 +28,7 @@
>>>>>>>>> #define PREFETCH_SHALLOW (1 << PREFETCH_SHIFT)
>>>>>>>>> #define PREFETCH_MODERATE (2 << PREFETCH_SHIFT)
>>>>>>>>> #define PREFETCH_DEEP (3 << PREFETCH_SHIFT)
>>>>>>>>> +#define GFX_ACTLR_PRR (1 << 5)
>>>>>>>>>
>>>>>>>>> static const struct actlr_config sc7280_apps_actlr_cfg[] = {
>>>>>>>>> { 0x0800, 0x04e0, PREFETCH_DEFAULT | CMTLB },
>>>>>>>>> @@ -235,6 +236,27 @@ static void qcom_adreno_smmu_resume_translation(const void *cookie, bool termina
>>>>>>>>> arm_smmu_cb_write(smmu, cfg->cbndx, ARM_SMMU_CB_RESUME, reg);
>>>>>>>>> }
>>>>>>>>>
>>>>>>>>> +static void qcom_adreno_smmu_set_prr(const void *cookie, phys_addr_t page_addr, bool set)
>>>>>>>>> +{
>>>>>>>>> + struct arm_smmu_domain *smmu_domain = (void *)cookie;
>>>>>>>>> + struct arm_smmu_cfg *cfg = &smmu_domain->cfg;
>>>>>>>>> + struct arm_smmu_device *smmu = smmu_domain->smmu;
>>>>>>>>> + u32 reg = 0;
>>>>>>>>> +
>>>>>>>>> + writel_relaxed(lower_32_bits(page_addr),
>>>>>>>>> + smmu->base + ARM_SMMU_GFX_PRR_CFG_LADDR);
>>>>>>>>> +
>>>>>>>>> + writel_relaxed(upper_32_bits(page_addr),
>>>>>>>>> + smmu->base + ARM_SMMU_GFX_PRR_CFG_UADDR);
>>>>>>>>> +
>>>>>>>>> + reg = arm_smmu_cb_read(smmu, cfg->cbndx, ARM_SMMU_CB_ACTLR);
>>>>>>>>> + reg &= ~GFX_ACTLR_PRR;
>>>>>>>>> + if (set)
>>>>>>>>> + reg |= FIELD_PREP(GFX_ACTLR_PRR, 1);
>>>>>>>>> + arm_smmu_cb_write(smmu, cfg->cbndx, ARM_SMMU_CB_ACTLR, reg);
>>>>>>>>> +
>>>>>>>>
>>>>>>>> nit, extra line
>>>>>>>>
>>>>>>>
>>>>>>> Ack, will remove this. Thanks for pointing out.
>>>>>>>
>>>>>>>> Also, if you passed a `struct page *` instead, then you could drop the
>>>>>>>> bool param, ie. passing NULL for the page would disable PRR. But I
>>>>>>>> can go either way if others have a strong preference for phys_addr_t.
>>>>>>>>
>>>>>>>
>>>>>>> Oh okay, this looks simple to reset the prr bit.
>>>>>>> But since this page is allocated and is used inside gfx driver
>>>>>>> before being utilized for prr bit operation, would it be safe for
>>>>>>> drm/gfx driver to keep a reference to this page in smmu driver?
>>>>>>>
>>>>>>> Since we only need the page address for configuring the
>>>>>>> CFG_UADDR/CFG_LADDR registers so passed the phys_addr_t.
>>>>>>
>>>>>> I don't think the smmu driver needs to keep a reference to the page..
>>>>>> we can just say it is the responsibility of the drm driver to call
>>>>>> set_prr(NULL) before freeing the page
>>>>>>
>>>>>
>>>>> That makes sense. If we go by this NULL page method to disable the PRR,
>>>>> we would have to set the address registers to reset value as well.
>>>>>
>>>>> The sequence would be like the following as per my understaning:
>>>>> - Check if it's NULL page
>>>>> - Set the PRR_CFG_UADDR/PRR_CFG_LADDR to reset values i.e - 0x0 for
>>>>> these registers
>>>>> - Reset the PRR bit in actlr register
>>>>>
>>>>> Similar to this snippet:
>>>>>
>>>>> #PRR_RESET_ADDR 0x0
>>>>>
>>>>> --------------
>>>>> reg = arm_smmu_cb_read(smmu, cfg->cbndx, ARM_SMMU_CB_ACTLR);
>>>>> reg &= ~GFX_ACTLR_PRR;
>>>>> arm_smmu_cb_write(smmu, cfg->cbndx, ARM_SMMU_CB_ACTLR, reg);
>>>>>
>>>>> if (!prr_page) {
>>>>> writel_relaxed(PRR_RESET_ADDR,
>>>>> smmu->base + ARM_SMMU_GFX_PRR_CFG_LADDR);
>>>>> writel_relaxed(PRR_RESET_ADDR),
>>>>> smmu->base + ARM_SMMU_GFX_PRR_CFG_UADDR);
>>>>> return;
>>>>> }
>>>>>
>>>>>
>>>>> writel_relaxed(lower_32_bits(page_to_phys(prr_page)),
>>>>> smmu->base + ARM_SMMU_GFX_PRR_CFG_LADDR);
>>>>>
>>>>> writel_relaxed(upper_32_bits(page_to_phys(prr_page)),
>>>>> smmu->base + ARM_SMMU_GFX_PRR_CFG_UADDR);
>>>>>
>>>>> reg |= FIELD_PREP(GFX_ACTLR_PRR, 1);
>>>>> arm_smmu_cb_write(smmu, cfg->cbndx, ARM_SMMU_CB_ACTLR, reg);
>>>>> -----------------
>>>>>
>>>>> If looks good, will implement the same in next version.
>>>>
>>>> yeah, that looks like it could work..
>>>>
>>>> you probably don't need to zero out the PRR_CFG_*ADDR when disabling,
>>>> and probably could avoid double writing ACTLR, but that is getting
>>>> into bikeshedding
>>>>
>>>
>>> Actually Rob, since you rightly pointed this out.
>>> I crosschecked again on these registers.
>>> PRR_CFG_*ADDR is a global register in SMMU space but
>>> ACTLR register including PRR bit is a per-domain register.
>>> There might also be a situation where PRR feature need to be
>>> disabled or enabled separately for each domain.
>>> So I think it would be cleaner to have two apis, set_prr_addr(),
>>> set_prr_bit().
>>> set_prr_addr() will be used only to set this PRR_CFG_*ADDR
>>> register by passing a 'struct page *'
>>> set_prr_bit() will be used as a switch for PRR feature,
>>> where required smmu_domain will be passed along with
>>> the bool value to set/reset the PRR bit depending on which this
>>> feature will be enabled/disabled for the selected domain.
>>
>> on a related note, adreno has been using arm-smmu for a number of
>> generations, I guess not all support PRR? The drm driver will need to
>> know whether PRR is supported (and expose that to userspace to let the
>> UMD know whether to expose certain extensions). How should this work?
>
> So, I noticed in the x1e80100.dtsi that there is a gpu_prr_mem
> reserved section.. maybe we should be connecting this to the smmu
> driver in dt, and using that to detect presence of PRR? Ie. the smmu
> driver would configure PRR_CFG_*ADDR based on the reserved mem, and
> the interface to drm would just be to enable/disable PRR, returning an
> error code if the reserved mem section isn't there.
>
> This simplifies the interface, and handles the question of how to
> detect if PRR is supported.
>
> BR,
> -R
>
As I checked gpu_prr_mem reserved mem section is not used for mobile
targets hence not present for other DT only compute targets like
x1e80100.dtsi has the same. PRR looks to be smmu version specific
property.
This feature is present in all the targets using SMMU-500,
I am still checking for targets using versions prior to smmu-500.
Then maybe we can use the smmu compatible string itself (e.g.
qcom,smmu-500 && qcom,adreno-smmu) to connect to smmu driver for
checking the presence of PRR ?
And if the compatible string is different then we can return the
error code signifying PRR feature is not supported on the particular
smmu version.
Thanks & regards,
Bibek
>> BR,
>> -R
>>
>>> Thanks & regards,
>>> Bibek
>>>
>>>> BR,
>>>> -R
>>>>
>>>>>
>>>>> Thanks & regards,
>>>>> Bibek
>>>>>
>>>>>> BR,
>>>>>> -R
>>>>>>
>>>>>>>> Otherwise, lgtm
>>>>>>>>
>>>>>>>> BR,
>>>>>>>> -R
>>>>>>>>
>>>>>>>
>>>>>>> Thanks & regards,
>>>>>>> Bibek
>>>>>>>
>>>>>>>>> +}
>>>>>>>>> +
>>>>>>>>> #define QCOM_ADRENO_SMMU_GPU_SID 0
>>>>>>>>>
>>>>>>>>> static bool qcom_adreno_smmu_is_gpu_device(struct device *dev)
>>>>>>>>> @@ -407,6 +429,7 @@ static int qcom_adreno_smmu_init_context(struct arm_smmu_domain *smmu_domain,
>>>>>>>>> priv->get_fault_info = qcom_adreno_smmu_get_fault_info;
>>>>>>>>> priv->set_stall = qcom_adreno_smmu_set_stall;
>>>>>>>>> priv->resume_translation = qcom_adreno_smmu_resume_translation;
>>>>>>>>> + priv->set_prr = qcom_adreno_smmu_set_prr;
>>>>>>>>>
>>>>>>>>> actlrvar = qsmmu->data->actlrvar;
>>>>>>>>> if (!actlrvar)
>>>>>>>>> diff --git a/drivers/iommu/arm/arm-smmu/arm-smmu.h b/drivers/iommu/arm/arm-smmu/arm-smmu.h
>>>>>>>>> index d9c2ef8c1653..3076bef49e20 100644
>>>>>>>>> --- a/drivers/iommu/arm/arm-smmu/arm-smmu.h
>>>>>>>>> +++ b/drivers/iommu/arm/arm-smmu/arm-smmu.h
>>>>>>>>> @@ -154,6 +154,8 @@ enum arm_smmu_cbar_type {
>>>>>>>>> #define ARM_SMMU_SCTLR_M BIT(0)
>>>>>>>>>
>>>>>>>>> #define ARM_SMMU_CB_ACTLR 0x4
>>>>>>>>> +#define ARM_SMMU_GFX_PRR_CFG_LADDR 0x6008
>>>>>>>>> +#define ARM_SMMU_GFX_PRR_CFG_UADDR 0x600C
>>>>>>>>>
>>>>>>>>> #define ARM_SMMU_CB_RESUME 0x8
>>>>>>>>> #define ARM_SMMU_RESUME_TERMINATE BIT(0)
>>>>>>>>> diff --git a/include/linux/adreno-smmu-priv.h b/include/linux/adreno-smmu-priv.h
>>>>>>>>> index c637e0997f6d..d6e2ca9f8d8c 100644
>>>>>>>>> --- a/include/linux/adreno-smmu-priv.h
>>>>>>>>> +++ b/include/linux/adreno-smmu-priv.h
>>>>>>>>> @@ -49,7 +49,10 @@ struct adreno_smmu_fault_info {
>>>>>>>>> * before set_ttbr0_cfg(). If stalling on fault is enabled,
>>>>>>>>> * the GPU driver must call resume_translation()
>>>>>>>>> * @resume_translation: Resume translation after a fault
>>>>>>>>> - *
>>>>>>>>> + * @set_prr: Extendible interface to be used by GPU to modify the
>>>>>>>>> + * ACTLR register bits, currently used to configure
>>>>>>>>> + * Partially-Resident-Region (PRR) feature's
>>>>>>>>> + * setup and reset sequence as requested.
>>>>>>>>> *
>>>>>>>>> * The GPU driver (drm/msm) and adreno-smmu work together for controlling
>>>>>>>>> * the GPU's SMMU instance. This is by necessity, as the GPU is directly
>>>>>>>>> @@ -67,6 +70,7 @@ struct adreno_smmu_priv {
>>>>>>>>> void (*get_fault_info)(const void *cookie, struct adreno_smmu_fault_info *info);
>>>>>>>>> void (*set_stall)(const void *cookie, bool enabled);
>>>>>>>>> void (*resume_translation)(const void *cookie, bool terminate);
>>>>>>>>> + void (*set_prr)(const void *cookie, phys_addr_t page_addr, bool set);
>>>>>>>>> };
>>>>>>>>>
>>>>>>>>> #endif /* __ADRENO_SMMU_PRIV_H */
>>>>>>>>> --
>>>>>>>>> 2.34.1
>>>>>>>>>
More information about the linux-arm-kernel
mailing list