[PATCH v3 3/3] arm64: hw_breakpoint: Save privilege of access control via ptrace

[Tiezhu Yang]

On 07/09/2024 06:05 PM, Will Deacon wrote:
> On Tue, Jul 09, 2024 at 05:55:06PM +0800, Tiezhu Yang wrote:
>> In the current code, decode_ctrl_reg() saves the privilege of access
>> control passed by the ptrace user data, but it is not used anymore,
>> arch_build_bp_info() checks whether bp virtual address is in kernel
>> space to construct hw->ctrl.privilege, it seems not reasonable.
>>
>> The value of ctrl->privilege saved in decode_ctrl_reg() can be used
>> in arch_build_bp_info(), there is no need to check bp virtual address
>> to assign value for hw->ctrl.privilege, just make use of "bp_priv" in
>> the struct perf_event_attr to save the privilege of access control via
>> ptrace for hardware breakpoint.
>>
>> Signed-off-by: Tiezhu Yang <yangtiezhu at loongson.cn>
>> ---
>>  arch/arm64/kernel/hw_breakpoint.c | 11 ++---------
>>  arch/arm64/kernel/ptrace.c        |  2 ++
>>  2 files changed, 4 insertions(+), 9 deletions(-)
>>
>> diff --git a/arch/arm64/kernel/hw_breakpoint.c b/arch/arm64/kernel/hw_breakpoint.c
>> index 722ac45f9f7b..06e34bcdcf92 100644
>> --- a/arch/arm64/kernel/hw_breakpoint.c
>> +++ b/arch/arm64/kernel/hw_breakpoint.c
>> @@ -486,15 +486,8 @@ static int arch_build_bp_info(struct perf_event *bp,
>>  	/* Address */
>>  	hw->address = attr->bp_addr;
>>
>> -	/*
>> -	 * Privilege
>> -	 * Note that we disallow combined EL0/EL1 breakpoints because
>> -	 * that would complicate the stepping code.
>> -	 */
>
> Just because you remove the comment doesn't mean that constraint no
> longer applies.

Yes, please see the following answer.

>
>> -	if (arch_check_bp_in_kernelspace(hw))
>> -		hw->ctrl.privilege = AARCH64_BREAKPOINT_EL1;
>> -	else
>> -		hw->ctrl.privilege = AARCH64_BREAKPOINT_EL0;
>> +	/* Privilege */
>> +	hw->ctrl.privilege = attr->bp_priv;
>>
>>  	/* Enabled? */
>>  	hw->ctrl.enabled = !attr->disabled;
>> diff --git a/arch/arm64/kernel/ptrace.c b/arch/arm64/kernel/ptrace.c
>> index 0d022599eb61..3b37c4a2e0d4 100644
>> --- a/arch/arm64/kernel/ptrace.c
>> +++ b/arch/arm64/kernel/ptrace.c
>> @@ -309,6 +309,7 @@ static struct perf_event *ptrace_hbp_create(unsigned int note_type,
>>  	attr.bp_addr	= 0;
>>  	attr.bp_len	= HW_BREAKPOINT_LEN_4;
>>  	attr.bp_type	= type;
>> +	attr.bp_priv	= AARCH64_BREAKPOINT_EL0;
>>  	attr.disabled	= 1;
>>
>>  	bp = register_user_hw_breakpoint(&attr, ptrace_hbptriggered, NULL, tsk);
>> @@ -352,6 +353,7 @@ static int ptrace_hbp_fill_attr_ctrl(unsigned int note_type,
>>  	attr->bp_len	= len;
>>  	attr->bp_type	= type;
>>  	attr->bp_addr	+= offset;
>> +	attr->bp_priv	= ctrl.privilege;
>
> Wait, so ptrace can now set breakpoints with arbitrary privileges?

The ptrace user should make sure the privilege is correct.
For example, the privilege is set as el0
in aarch64_point_encode_ctrl_reg() of GDB:

   /* enabled at el0 */
   ctrl |= (2 << 1) | 1;

https://sourceware.org/git/?p=binutils-gdb.git;a=blob;f=gdb/nat/aarch64-hw-point.c#l135

Thanks,
Tiezhu