[PATCH] ARM: dts: stm32: Describe PHY LEDs in DH STM32MP13xx DHCOR DHSBC board DT

[Marek Vasut]

The RTL8211 PHY on DH STM32MP13xx DHCOR DHSBC carrier board supports HW
LED offload, the LEDs can be configured on link at 10/100/1000 line rate
and on RXTX activity. There are two PHYs on this board, each only has two
out of three LEDs connected to the PHY LED outputs. Describe this hardware
configuration in DT.

Signed-off-by: Marek Vasut <marex at denx.de>
---
Cc: Alexandre Torgue <alexandre.torgue at foss.st.com>
Cc: Christophe Roullier <christophe.roullier at foss.st.com>
Cc: Conor Dooley <conor+dt at kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt at kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32 at gmail.com>
Cc: Rob Herring <robh at kernel.org>
Cc: devicetree at vger.kernel.org
Cc: kernel at dh-electronics.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: linux-stm32 at st-md-mailman.stormreply.com
---
 .../boot/dts/st/stm32mp135f-dhcor-dhsbc.dts   | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
index 1b916c419e8e2..c80a6ecdb47a6 100644
--- a/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
+++ b/arch/arm/boot/dts/st/stm32mp135f-dhcor-dhsbc.dts
@@ -100,6 +100,25 @@ ethphy1: ethernet-phy at 1 {
 			reset-assert-us = <15000>;
 			reset-deassert-us = <55000>;
 			reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led at 0 {
+					reg = <0>;
+					color = <LED_COLOR_ID_GREEN>;
+					function = LED_FUNCTION_WAN;
+					linux,default-trigger = "netdev";
+				};
+
+				led at 1 {
+					reg = <1>;
+					color = <LED_COLOR_ID_YELLOW>;
+					function = LED_FUNCTION_WAN;
+					linux,default-trigger = "netdev";
+				};
+			};
 		};
 	};
 };
@@ -130,6 +149,25 @@ ethphy2: ethernet-phy at 1 {
 			reset-assert-us = <15000>;
 			reset-deassert-us = <55000>;
 			reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led at 0 {
+					reg = <0>;
+					color = <LED_COLOR_ID_GREEN>;
+					function = LED_FUNCTION_LAN;
+					linux,default-trigger = "netdev";
+				};
+
+				led at 1 {
+					reg = <1>;
+					color = <LED_COLOR_ID_YELLOW>;
+					function = LED_FUNCTION_LAN;
+					linux,default-trigger = "netdev";
+				};
+			};
 		};
 	};
 };
-- 
2.43.0