[PATCH 1/2] dt-bindings: soc: fsl: cpm_qe: convert to yaml format
Frank Li
Frank.Li at nxp.com
Wed Jul 3 09:49:39 PDT 2024
Convert binding doc qe.txt to yaml format. Split it to
fsl,qe-firmware.yaml, fsl,qe-ic.yaml, fsl,qe-muram.yaml, fsl,qe-si.yaml
fsl,qe-siram.yaml, fsl,qe.yaml.
Additional Changes:
- Fix error in example.
- Change to low case for hex value.
- Remove fsl,qe-num-riscs and fsl,qe-snums from required list.
- Add #address-cell and #size-cell.
- Add interrupts description for qe-ic.
- Add compatible string fsl,ls1043-qe-si for fsl,qe-si.yaml
- Add compatible string fsl,ls1043-qe-siram for fsl,qe-siram.yaml
- Add child node for fsl,qe.yaml
Fix below warning:
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: /soc/uqe at 2400000/muram at 10000: failed to match any schema with compatible: ['fsl,qe-muram', 'fsl,cpm-muram']
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: /soc/uqe at 2400000/muram at 10000: failed to match any schema with compatible: ['fsl,qe-muram', 'fsl,cpm-muram']
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: /soc/uqe at 2400000/muram at 10000/data-only at 0: failed to match any schema with compatible: ['fsl,qe-muram-data', 'fsl,cpm-muram-data']
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: /soc/uqe at 2400000: failed to match any schema with compatible: ['fsl,qe', 'simple-bus']
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: /soc/uqe at 2400000/muram at 10000/data-only at 0: failed to match any schema with compatible: ['fsl,qe-muram-data', 'fsl,cpm-muram-data']
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: /soc/uqe at 2400000/qeic at 80: failed to match any schema with compatible: ['fsl,qe-ic']
Signed-off-by: Frank Li <Frank.Li at nxp.com>
---
.../bindings/soc/fsl/cpm_qe/fsl,qe-firmware.yaml | 48 ++++++
.../bindings/soc/fsl/cpm_qe/fsl,qe-ic.yaml | 47 ++++++
.../bindings/soc/fsl/cpm_qe/fsl,qe-muram.yaml | 71 ++++++++
.../bindings/soc/fsl/cpm_qe/fsl,qe-si.yaml | 40 +++++
.../bindings/soc/fsl/cpm_qe/fsl,qe-siram.yaml | 39 +++++
.../devicetree/bindings/soc/fsl/cpm_qe/fsl,qe.yaml | 148 +++++++++++++++++
.../devicetree/bindings/soc/fsl/cpm_qe/qe.txt | 178 ---------------------
7 files changed, 393 insertions(+), 178 deletions(-)
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-firmware.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-firmware.yaml
new file mode 100644
index 0000000000000..53b07d4edc773
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-firmware.yaml
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-firmware.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine module Firmware Node
+
+maintainers:
+ - Frank Li <Frank.Li at nxp.com>
+
+description: |
+ This node defines a firmware binary that is embedded in the device tree, for
+ the purpose of passing the firmware from bootloader to the kernel, or from
+ the hypervisor to the guest.
+
+ The firmware node itself contains the firmware binary contents, a compatible
+ property, and any firmware-specific properties. The node should be placed
+ inside a QE node that needs it. Doing so eliminates the need for a
+ fsl,firmware-phandle property. Other QE nodes that need the same firmware
+ should define an fsl,firmware-phandle property that points to the firmware node
+ in the first QE node.
+
+ The fsl,firmware property can be specified in the DTS (possibly using incbin)
+ or can be inserted by the boot loader at boot time.
+
+properties:
+ compatible:
+ enum:
+ - fsl,qe-firmware
+
+ fsl,firmware:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ description:
+ A standard property. This property contains the firmware binary "blob".
+
+required:
+ - compatible
+ - fsl,firmware
+
+additionalProperties: false
+
+examples:
+ - |
+ qe-firmware {
+ compatible = "fsl,qe-firmware";
+ fsl,firmware = <0x70 0xcd 0x00 0x00 0x01 0x46 0x45>;
+ };
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ic.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ic.yaml
new file mode 100644
index 0000000000000..8267ad00727b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-ic.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-ic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine module Interrupt Controller (IC)
+
+maintainers:
+ - Frank Li <Frank.Li at nxp.com>
+
+properties:
+ compatible:
+ const: fsl,qe-ic
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: QE interrupt
+ - description: QE critical
+ - description: QE error
+ minItems: 1
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - interrupt-controller
+ - "#interrupt-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ interrupt-controller at 80 {
+ compatible = "fsl,qe-ic";
+ reg = <0x80 0x80>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupts = <95 2 0 0 94 2 0 0>;
+ };
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-muram.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-muram.yaml
new file mode 100644
index 0000000000000..cf0f38dbbe0da
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-muram.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-muram.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine Multi-User RAM (MURAM)
+
+maintainers:
+ - Frank Li <Frank.Li at nxp.com>
+
+description: Multi-User RAM (MURAM)
+
+properties:
+ compatible:
+ items:
+ - const: fsl,qe-muram
+ - const: fsl,cpm-muram
+
+ ranges:
+ maxItems: 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 1
+
+ mode:
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [host, slave]
+
+
+patternProperties:
+ '^data\-only@[a-f0-9]+$':
+ type: object
+ properties:
+ compatible:
+ items:
+ - const: fsl,qe-muram-data
+ - const: fsl,cpm-muram-data
+
+ reg:
+ maxItems: 1
+
+ required:
+ - compatible
+ - reg
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ muram at 10000 {
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0 0x00010000 0x0000c000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ data-only at 0{
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0 0xc000>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-si.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-si.yaml
new file mode 100644
index 0000000000000..8e58ab58c0633
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-si.yaml
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-si.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine module Serial Interface Block (SI)
+
+maintainers:
+ - Frank Li <Frank.Li at nxp.com>
+
+description:
+ The SI manages the routing of eight TDM lines to the QE block serial drivers,
+ the MCC and the UCCs, for receive and transmit.
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - fsl,ls1043-qe-si
+ - const: fsl,t1040-qe-si
+ - enum:
+ - fsl,t1040-qe-si
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ si at 700 {
+ compatible = "fsl,t1040-qe-si";
+ reg = <0x700 0x80>;
+ };
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-siram.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-siram.yaml
new file mode 100644
index 0000000000000..cc4ed48d786c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe-siram.yaml
@@ -0,0 +1,39 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe-siram.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine module Serial Interface Block RAM(SIRAM)
+
+maintainers:
+ - Frank Li <Frank.Li at nxp.com>
+
+description:
+ store the routing entries of SI
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - fsl,ls1043-qe-siram
+ - const: fsl,t1040-qe-siram
+ - const: fsl,t1040-qe-siram
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ siram at 1000 {
+ compatible = "fsl,t1040-qe-siram";
+ reg = <0x1000 0x800>;
+ };
+
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe.yaml
new file mode 100644
index 0000000000000..89cdf5e1d0a8d
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,qe.yaml
@@ -0,0 +1,148 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,qe.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale QUICC Engine module (QE)
+
+maintainers:
+ - Frank Li <Frank.Li at nxp.com>
+
+description: |
+ This represents qe module that is installed on PowerQUICC II Pro.
+
+ NOTE: This is an interim binding; it should be updated to fit
+ in with the CPM binding later in this document.
+
+ Basically, it is a bus of devices, that could act more or less
+ as a complete entity (UCC, USB etc ). All of them should be siblings on
+ the "root" qe node, using the common properties from there.
+ The description below applies to the qe of MPC8360 and
+ more nodes and properties would be extended in the future.
+
+properties:
+ compatible:
+ items:
+ - const: fsl,qe
+ - const: simple-bus
+
+ reg:
+ maxItems: 1
+
+ ranges:
+ maxItems: 1
+
+ model:
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [QE, CPM, CPM2]
+
+ bus-frequency:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: the clock frequency for QUICC Engine.
+
+ fsl,qe-num-riscs:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: define how many RISC engines the QE has.
+
+ fsl,qe-snums:
+ $ref: /schemas/types.yaml#/definitions/uint8-array
+ maxItems: 28
+ description:
+ defining the array of serial number (SNUM) values for the virtual
+ threads.
+
+ fsl,firmware-phandle:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: |
+ required only if there is no fsl,qe-firmware child node
+
+ Points to a firmware node (see "QE Firmware Node" below)
+ that contains the firmware that should be uploaded for this QE.
+ The compatible property for the firmware node should say,
+ "fsl,qe-firmware".
+
+ brg-frequency:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ the internal clock source frequency for baud-rate
+ generators in Hz.
+
+ fsl,qe-num-snums:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ deprecated: true
+ description: |
+ define how many serial number(SNUM) the QE can use
+ for the threads. Use fsl,qe-snums instead to not only specify the
+ number of snums, but also their values.
+
+patternProperties:
+ '^muram@[a-f0-9]+$':
+ $ref: fsl,qe-muram.yaml
+
+ '^interrupt-controller@[a-f0-9]+$':
+ $ref: fsl,qe-ic.yaml
+
+ '^si@[a-f0-9]+$':
+ $ref: fsl,qe-si.yaml
+
+ '^siram@[a-f0-9]+$':
+ $ref: fsl,qe-siram.yaml
+
+required:
+ - compatible
+ - reg
+ - bus-frequency
+
+allOf:
+ - $ref: /schemas/simple-bus.yaml#
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ qe-bus at e0100000 {
+ compatible = "fsl,qe", "simple-bus";
+ reg = <0xe0100000 0x480>;
+ ranges = <0 0xe0100000 0x00100000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ brg-frequency = <0>;
+ bus-frequency = <0x179a7b00>;
+ fsl,qe-snums = /bits/ 8 <
+ 0x04 0x05 0x0c 0x0d 0x14 0x15 0x1c 0x1d
+ 0x24 0x25 0x2c 0x2d 0x34 0x35 0x88 0x89
+ 0x98 0x99 0xa8 0xa9 0xb8 0xb9 0xc8 0xc9
+ 0xd8 0xd9 0xe8 0xe9>;
+
+ interrupt-controller at 80 {
+ compatible = "fsl,qe-ic";
+ reg = <0x80 0x80>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupts = <95 2 0 0 94 2 0 0>;
+ };
+
+ si at 700 {
+ compatible = "fsl,t1040-qe-si";
+ reg = <0x700 0x80>;
+ };
+
+ siram at 1000 {
+ compatible = "fsl,t1040-qe-siram";
+ reg = <0x1000 0x800>;
+ };
+
+ muram at 10000 {
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0 0x00010000 0x0000c000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ data-only at 0{
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0 0xc000>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
deleted file mode 100644
index 05ec2a838c54b..0000000000000
--- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
+++ /dev/null
@@ -1,178 +0,0 @@
-* Freescale QUICC Engine module (QE)
-This represents qe module that is installed on PowerQUICC II Pro.
-
-NOTE: This is an interim binding; it should be updated to fit
-in with the CPM binding later in this document.
-
-Basically, it is a bus of devices, that could act more or less
-as a complete entity (UCC, USB etc ). All of them should be siblings on
-the "root" qe node, using the common properties from there.
-The description below applies to the qe of MPC8360 and
-more nodes and properties would be extended in the future.
-
-i) Root QE device
-
-Required properties:
-- compatible : should be "fsl,qe";
-- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
-- reg : offset and length of the device registers.
-- bus-frequency : the clock frequency for QUICC Engine.
-- fsl,qe-num-riscs: define how many RISC engines the QE has.
-- fsl,qe-snums: This property has to be specified as '/bits/ 8' value,
- defining the array of serial number (SNUM) values for the virtual
- threads.
-
-Optional properties:
-- fsl,firmware-phandle:
- Usage: required only if there is no fsl,qe-firmware child node
- Value type: <phandle>
- Definition: Points to a firmware node (see "QE Firmware Node" below)
- that contains the firmware that should be uploaded for this QE.
- The compatible property for the firmware node should say,
- "fsl,qe-firmware".
-
-Recommended properties
-- brg-frequency : the internal clock source frequency for baud-rate
- generators in Hz.
-
-Deprecated properties
-- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use
- for the threads. Use fsl,qe-snums instead to not only specify the
- number of snums, but also their values.
-
-Example:
- qe at e0100000 {
- #address-cells = <1>;
- #size-cells = <1>;
- #interrupt-cells = <2>;
- compatible = "fsl,qe";
- ranges = <0 e0100000 00100000>;
- reg = <e0100000 480>;
- brg-frequency = <0>;
- bus-frequency = <179A7B00>;
- fsl,qe-snums = /bits/ 8 <
- 0x04 0x05 0x0C 0x0D 0x14 0x15 0x1C 0x1D
- 0x24 0x25 0x2C 0x2D 0x34 0x35 0x88 0x89
- 0x98 0x99 0xA8 0xA9 0xB8 0xB9 0xC8 0xC9
- 0xD8 0xD9 0xE8 0xE9>;
- }
-
-* Multi-User RAM (MURAM)
-
-Required properties:
-- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
-- mode : the could be "host" or "slave".
-- ranges : Should be defined as specified in 1) to describe the
- translation of MURAM addresses.
-- data-only : sub-node which defines the address area under MURAM
- bus that can be allocated as data/parameter
-
-Example:
-
- muram at 10000 {
- compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0 00010000 0000c000>;
-
- data-only at 0{
- compatible = "fsl,qe-muram-data",
- "fsl,cpm-muram-data";
- reg = <0 c000>;
- };
- };
-
-* Interrupt Controller (IC)
-
-Required properties:
-- compatible : should be "fsl,qe-ic".
-- reg : Address range of IC register set.
-- interrupts : interrupts generated by the device.
-- interrupt-controller : this device is a interrupt controller.
-
-Example:
-
- qeic: interrupt-controller at 80 {
- interrupt-controller;
- compatible = "fsl,qe-ic";
- #address-cells = <0>;
- #interrupt-cells = <1>;
- reg = <0x80 0x80>;
- interrupts = <95 2 0 0 94 2 0 0>;
- };
-
-* Serial Interface Block (SI)
-
-The SI manages the routing of eight TDM lines to the QE block serial drivers
-, the MCC and the UCCs, for receive and transmit.
-
-Required properties:
-- compatible : must be "fsl,<chip>-qe-si". For t1040, must contain
- "fsl,t1040-qe-si".
-- reg : Address range of SI register set.
-
-Example:
-
- si1: si at 700 {
- compatible = "fsl,t1040-qe-si";
- reg = <0x700 0x80>;
- };
-
-* Serial Interface Block RAM(SIRAM)
-
-store the routing entries of SI
-
-Required properties:
-- compatible : should be "fsl,<chip>-qe-siram". For t1040, must contain
- "fsl,t1040-qe-siram".
-- reg : Address range of SI RAM.
-
-Example:
-
- siram1: siram at 1000 {
- compatible = "fsl,t1040-qe-siram";
- reg = <0x1000 0x800>;
- };
-
-* QE Firmware Node
-
-This node defines a firmware binary that is embedded in the device tree, for
-the purpose of passing the firmware from bootloader to the kernel, or from
-the hypervisor to the guest.
-
-The firmware node itself contains the firmware binary contents, a compatible
-property, and any firmware-specific properties. The node should be placed
-inside a QE node that needs it. Doing so eliminates the need for a
-fsl,firmware-phandle property. Other QE nodes that need the same firmware
-should define an fsl,firmware-phandle property that points to the firmware node
-in the first QE node.
-
-The fsl,firmware property can be specified in the DTS (possibly using incbin)
-or can be inserted by the boot loader at boot time.
-
-Required properties:
- - compatible
- Usage: required
- Value type: <string>
- Definition: A standard property. Specify a string that indicates what
- kind of firmware it is. For QE, this should be "fsl,qe-firmware".
-
- - fsl,firmware
- Usage: required
- Value type: <prop-encoded-array>, encoded as an array of bytes
- Definition: A standard property. This property contains the firmware
- binary "blob".
-
-Example:
- qe1 at e0080000 {
- compatible = "fsl,qe";
- qe_firmware:qe-firmware {
- compatible = "fsl,qe-firmware";
- fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...];
- };
- ...
- };
-
- qe2 at e0090000 {
- compatible = "fsl,qe";
- fsl,firmware-phandle = <&qe_firmware>;
- ...
- };
--
2.34.1
More information about the linux-arm-kernel
mailing list