[PATCH v2 1/4] arm64: dts: rockchip: enable built-in thermal monitoring on rk3588

[Dragan Simic]

Hello Alexey,

Some small nitpicks below, please have a look.

On 2024-01-30 19:21, Alexey Charkov wrote:
> Include thermal zones information in device tree for rk3588 variants

Please use "RK3588" instead of "rk3588", both here and in the
patch subject.  Looks much better.

> Signed-off-by: Alexey Charkov <alchark at gmail.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 162 
> ++++++++++++++++++++++++++++++
>  1 file changed, 162 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> index 36b1b7acfe6a..696cb72d75d0 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> @@ -10,6 +10,7 @@
>  #include <dt-bindings/reset/rockchip,rk3588-cru.h>
>  #include <dt-bindings/phy/phy.h>
>  #include <dt-bindings/ata/ahci.h>
> +#include <dt-bindings/thermal/thermal.h>
> 
>  / {
>  	compatible = "rockchip,rk3588";
> @@ -2228,6 +2229,167 @@ tsadc: tsadc at fec00000 {
>  		status = "disabled";
>  	};
> 
> +	thermal_zones: thermal-zones {
> +		/* sensor near the center of the whole chip */

It would be good to replace "whole chip" with "SoC".  Simpler and
IIRC closer to the official description of the sensor.

> +		package_thermal: package-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 0>;
> +
> +			trips {
> +				package_crit: package-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		/* sensor between A76 cores 0 and 1 */
> +		bigcore0_thermal: bigcore0-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 1>;
> +
> +			trips {

Please add the following comment here, to make it clear what's
the purpose of this thermal trip when the IPA thermal governor
is used (more similar comments below):

                                 /* IPA threshold */

> +				bigcore0_alert0: bigcore0-alert0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};

Please add the following comment here:

                                 /* IPA target */

> +				bigcore0_alert1: bigcore0-alert1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				bigcore0_crit: bigcore0-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&bigcore0_alert1>;
> +					cooling-device =
> +						<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_b1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		/* sensor between A76 cores 2 and 3 */
> +		bigcore2_thermal: bigcore2-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 2>;
> +
> +			trips {

Please add the following comment here:

                                 /* IPA threshold */

> +				bigcore2_alert0: bigcore2-alert0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};

Please add the following comment here:

                                 /* IPA target */

> +				bigcore2_alert1: bigcore2-alert1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				bigcore2_crit: bigcore2-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&bigcore2_alert1>;
> +					cooling-device =
> +						<&cpu_b2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_b3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		/* sensor between the four A55 cores */
> +		little_core_thermal: littlecore-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 3>;
> +
> +			trips {

Please add the following comment here:

                                 /* IPA threshold */

> +				littlecore_alert0: littlecore-alert0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};

Please add the following comment here:

                                 /* IPA target */

> +				littlecore_alert1: littlecore-alert1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +				littlecore_crit: littlecore-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +			cooling-maps {
> +				map0 {
> +					trip = <&littlecore_alert1>;
> +					cooling-device =
> +						<&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_l1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_l2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu_l3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +
> +		/* sensor near the PD_CENTER power domain */
> +		center_thermal: center-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 4>;
> +
> +			trips {
> +				center_crit: center-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		gpu_thermal: gpu-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 5>;
> +
> +			trips {
> +				gpu_crit: gpu-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		npu_thermal: npu-thermal {
> +			polling-delay-passive = <0>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&tsadc 6>;
> +
> +			trips {
> +				npu_crit: npu-crit {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
> +
>  	saradc: adc at fec10000 {
>  		compatible = "rockchip,rk3588-saradc";
>  		reg = <0x0 0xfec10000 0x0 0x10000>;