[PATCH v3 2/2] perf/marvell : Odyssey LLC-TAD performance monitor support

[Jonathan Cameron]

On Mon, 22 Jan 2024 18:19:33 +0530
Gowthami Thiagarajan <gthiagarajan at marvell.com> wrote:

> Each TAD provides eight 64-bit counters for monitoring
> cache behavior.The driver always configures the same counter for
> all the TADs. The user would end up effectively reserving one of
> eight counters in every TAD to look across all TADs.
> The occurrences of events are aggregated and presented to the user
> at the end of running the workload. The driver does not provide a
> way for the user to partition TADs so that different TADs are used for
> different applications.
> 
> The performance events reflect various internal or interface activities.
> By combining the values from multiple performance counters, cache
> performance can be measured in terms such as: cache miss rate, cache
> allocations, interface retry rate, internal resource occupancy, etc.
> 
> Each supported counter's event and formatting information is exposed
> to sysfs at /sys/devices/tad/. Use perf tool stat command to measure
> the pmu events. For instance:
> 
> perf stat -e tad_hit_ltg,tad_hit_dtg <workload>
> 
> Signed-off-by: Gowthami Thiagarajan <gthiagarajan at marvell.com>
Hi Gowthami,

A few quick comments inline

Jonathan

> ---
>  drivers/perf/marvell_cn10k_tad_pmu.c | 41 +++++++++++++++++++++++++++-
>  1 file changed, 40 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/perf/marvell_cn10k_tad_pmu.c b/drivers/perf/marvell_cn10k_tad_pmu.c
> index fec8e82edb95..b5786fcec0ec 100644
> --- a/drivers/perf/marvell_cn10k_tad_pmu.c
> +++ b/drivers/perf/marvell_cn10k_tad_pmu.c
> @@ -214,6 +214,24 @@ static const struct attribute_group tad_pmu_events_attr_group = {
>  	.attrs = tad_pmu_event_attrs,
>  };
>  
> +static struct attribute *ody_tad_pmu_event_attrs[] = {
> +	TAD_PMU_EVENT_ATTR(tad_req_msh_in_exlmn, 0x3),
> +	TAD_PMU_EVENT_ATTR(tad_alloc_dtg, 0x1a),
> +	TAD_PMU_EVENT_ATTR(tad_alloc_ltg, 0x1b),
> +	TAD_PMU_EVENT_ATTR(tad_alloc_any, 0x1c),
> +	TAD_PMU_EVENT_ATTR(tad_hit_dtg, 0x1d),
> +	TAD_PMU_EVENT_ATTR(tad_hit_ltg, 0x1e),
> +	TAD_PMU_EVENT_ATTR(tad_hit_any, 0x1f),
> +	TAD_PMU_EVENT_ATTR(tad_tag_rd, 0x20),
> +	TAD_PMU_EVENT_ATTR(tad_tot_cycle, 0xFF),
> +	NULL
> +};
> +
> +static const struct attribute_group ody_tad_pmu_events_attr_group = {
> +	.name = "events",
> +	.attrs = ody_tad_pmu_event_attrs,
> +};
> +
>  PMU_FORMAT_ATTR(event, "config:0-7");
>  
>  static struct attribute *tad_pmu_format_attrs[] = {
> @@ -252,11 +270,19 @@ static const struct attribute_group *tad_pmu_attr_groups[] = {
>  	NULL
>  };
>  
> +static const struct attribute_group *ody_tad_pmu_attr_groups[] = {
> +	&ody_tad_pmu_events_attr_group,
> +	&tad_pmu_format_attr_group,
> +	&tad_pmu_cpumask_attr_group,
> +	NULL
> +};
> +
>  static int tad_pmu_probe(struct platform_device *pdev)
>  {
>  	struct device *dev = &pdev->dev;
>  	struct tad_region *regions;
>  	struct tad_pmu *tad_pmu;
> +	const char *compatible;
>  	struct resource *res;
>  	u32 tad_pmu_page_size;
>  	u32 tad_page_size;
> @@ -276,6 +302,12 @@ static int tad_pmu_probe(struct platform_device *pdev)
>  		return -ENODEV;
>  	}
>  
> +	ret = device_property_read_string(dev, "compatible", &compatible);
Unusual to find a compatible in an ACPI DSDT table unless PRP0001 is being used
and if that is being used, I'd not expect ACPI ID as below.

Maybe give a DSDT blob (disassembled) in the patch intro?

> +	if (ret) {
> +		dev_err(&pdev->dev, "compatible property not found\n");
> +		return ret;
> +	}
> +
>  	ret = device_property_read_u32(dev, "marvell,tad-page-size",
>  				       &tad_page_size);
>  	if (ret) {
> @@ -319,7 +351,6 @@ static int tad_pmu_probe(struct platform_device *pdev)
>  	tad_pmu->pmu = (struct pmu) {
>  
>  		.module		= THIS_MODULE,
> -		.attr_groups	= tad_pmu_attr_groups,
>  		.capabilities	= PERF_PMU_CAP_NO_EXCLUDE |
>  				  PERF_PMU_CAP_NO_INTERRUPT,
>  		.task_ctx_nr	= perf_invalid_context,
> @@ -332,6 +363,13 @@ static int tad_pmu_probe(struct platform_device *pdev)
>  		.read		= tad_pmu_event_counter_read,
>  	};
>  
> +	if ((strncmp("marvell,cn10k-ddr-pmu", compatible,
> +		     strlen(compatible)) == 0)) {

How does this work with the ACPI ID added below?  Also, just
put this in the tables so device_get_match_data() can retrieve it
instead of string matching in here.


> +		tad_pmu->pmu.attr_groups = tad_pmu_attr_groups;
> +	} else {
> +		tad_pmu->pmu.attr_groups = ody_tad_pmu_attr_groups;
> +	}
> +
>  	tad_pmu->cpu = raw_smp_processor_id();
>  
>  	/* Register pmu instance for cpu hotplug */
> @@ -372,6 +410,7 @@ static const struct of_device_id tad_pmu_of_match[] = {
>  #ifdef CONFIG_ACPI
>  static const struct acpi_device_id tad_pmu_acpi_match[] = {
>  	{"MRVL000B", 0},
> +	{"MRVL000D", 0},
>  	{},
>  };
>  MODULE_DEVICE_TABLE(acpi, tad_pmu_acpi_match);