[PATCH v2 15/15] PCI: j721e: add suspend and resume support

[Thomas Richard]

From: Théo Lebrun <theo.lebrun at bootlin.com>

Add suspend and resume support. Only the rc mode is supported.

During the suspend stage PERST# is asserted, then deasserted during the
resume stage.

Signed-off-by: Théo Lebrun <theo.lebrun at bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard at bootlin.com>
---
 drivers/pci/controller/cadence/pci-j721e.c | 79 ++++++++++++++++++++++++++++++
 1 file changed, 79 insertions(+)

diff --git a/drivers/pci/controller/cadence/pci-j721e.c b/drivers/pci/controller/cadence/pci-j721e.c
index 477275d72257..668d98422c4d 100644
--- a/drivers/pci/controller/cadence/pci-j721e.c
+++ b/drivers/pci/controller/cadence/pci-j721e.c
@@ -6,6 +6,7 @@
  * Author: Kishon Vijay Abraham I <kishon at ti.com>
  */
 
+#include <linux/clk-provider.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/gpio/consumer.h>
@@ -18,10 +19,13 @@
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/regmap.h>
+#include <linux/container_of.h>
 
 #include "../../pci.h"
 #include "pcie-cadence.h"
 
+#define cdns_pcie_to_rc(p) container_of(p, struct cdns_pcie_rc, pcie)
+
 #define ENABLE_REG_SYS_2	0x108
 #define STATUS_REG_SYS_2	0x508
 #define STATUS_CLR_REG_SYS_2	0x708
@@ -554,6 +558,80 @@ static void j721e_pcie_remove(struct platform_device *pdev)
 	pm_runtime_disable(dev);
 }
 
+static int j721e_pcie_suspend_noirq(struct device *dev)
+{
+	struct j721e_pcie *pcie = dev_get_drvdata(dev);
+
+	if (pcie->mode == PCI_MODE_RC) {
+		gpiod_set_value_cansleep(pcie->reset_gpio, 0);
+		clk_disable_unprepare(pcie->refclk);
+	}
+
+	cdns_pcie_disable_phy(pcie->cdns_pcie);
+
+	return 0;
+}
+
+static int j721e_pcie_resume_noirq(struct device *dev)
+{
+	struct j721e_pcie *pcie = dev_get_drvdata(dev);
+	struct cdns_pcie *cdns_pcie = pcie->cdns_pcie;
+	int ret;
+
+	ret = j721e_pcie_ctrl_init(pcie);
+	if (ret < 0) {
+		dev_err(dev, "j721e_pcie_ctrl_init failed\n");
+		return ret;
+	}
+
+	j721e_pcie_config_link_irq(pcie);
+
+	/*
+	 * This is not called explicitly in the probe, it is called by
+	 * cdns_pcie_init_phy.
+	 */
+	ret = cdns_pcie_enable_phy(pcie->cdns_pcie);
+	if (ret < 0) {
+		dev_err(dev, "cdns_pcie_enable_phy failed\n");
+		return -ENODEV;
+	}
+
+	if (pcie->mode == PCI_MODE_RC) {
+		struct cdns_pcie_rc *rc = cdns_pcie_to_rc(cdns_pcie);
+
+		ret = clk_prepare_enable(pcie->refclk);
+		if (ret < 0) {
+			dev_err(dev, "clk_prepare_enable failed\n");
+			return -ENODEV;
+		}
+
+		/*
+		 * "Power Sequencing and Reset Signal Timings" table in
+		 * PCI EXPRESS CARD ELECTROMECHANICAL SPECIFICATION, REV. 3.0
+		 * indicates PERST# should be deasserted after minimum of 100us
+		 * once REFCLK is stable. The REFCLK to the connector in RC
+		 * mode is selected while enabling the PHY. So deassert PERST#
+		 * after 100 us.
+		 */
+		if (pcie->reset_gpio) {
+			usleep_range(100, 200);
+			gpiod_set_value_cansleep(pcie->reset_gpio, 1);
+		}
+
+		ret = cdns_pcie_host_setup(rc, false);
+		if (ret < 0) {
+			clk_disable_unprepare(pcie->refclk);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static DEFINE_NOIRQ_DEV_PM_OPS(j721e_pcie_pm_ops,
+			       j721e_pcie_suspend_noirq,
+			       j721e_pcie_resume_noirq);
+
 static struct platform_driver j721e_pcie_driver = {
 	.probe  = j721e_pcie_probe,
 	.remove_new = j721e_pcie_remove,
@@ -561,6 +639,7 @@ static struct platform_driver j721e_pcie_driver = {
 		.name	= "j721e-pcie",
 		.of_match_table = of_j721e_pcie_match,
 		.suppress_bind_attrs = true,
+		.pm	= pm_sleep_ptr(&j721e_pcie_pm_ops),
 	},
 };
 builtin_platform_driver(j721e_pcie_driver);

-- 
2.39.2