[PATCH v1 2/2] arm64: dts: freescale: imx8qm: add apalis eval v1.2 carrier board

Francesco Dolcini francesco at dolcini.it
Thu Jan 25 02:14:57 PST 2024 

From: Joao Paulo Goncalves <joao.goncalves at toradex.com>

Add support for the new version, v1.2, of Apalis Evaluation Board.
Because only imx8-apalis-eval.dtsi was available and used as the only
board configuration for board version v1.0 and v1.1, it was changed to
be the common hardware configurations for all versions v1.0,
v1.1 and v1.2. Also, two .dtsi board files were added to have the
differences by board. The .dts were organized by SoM and board version.

Board versions v1.0 and v1.1 are compatible with each other and should
use imx8qm-apalis-eval.dts file or imx8qm-apalis-v1.1-eval.dts file
depending on SoM version. Now for v1.2, organized by SoM version too, the
files are imx8qm-apalis-eval-v1.2.dts and imx8qm-apalis-v1.1-eval-v1.2.dts.

Signed-off-by: Joao Paulo Goncalves <joao.goncalves at toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini at toradex.com>
---
 arch/arm64/boot/dts/freescale/Makefile        |   2 +
 .../dts/freescale/imx8-apalis-eval-v1.1.dtsi  |  26 ++++
 .../dts/freescale/imx8-apalis-eval-v1.2.dtsi  | 124 ++++++++++++++++++
 .../boot/dts/freescale/imx8-apalis-eval.dtsi  |  22 ----
 .../dts/freescale/imx8qm-apalis-eval-v1.2.dts |  16 +++
 .../boot/dts/freescale/imx8qm-apalis-eval.dts |   2 +-
 .../imx8qm-apalis-v1.1-eval-v1.2.dts          |  26 ++++
 .../dts/freescale/imx8qm-apalis-v1.1-eval.dts |   2 +-
 8 files changed, 196 insertions(+), 24 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.1.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.2.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-apalis-eval-v1.2.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval-v1.2.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 2e027675d7bb..91f3371982b5 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -188,8 +188,10 @@ imx8mq-tqma8mq-mba8mx-lvds-tm070jvhg33-dtbs += imx8mq-tqma8mq-mba8mx.dtb imx8mq-
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-tqma8mq-mba8mx-lvds-tm070jvhg33.dtb
 
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-eval.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-eval-v1.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-ixora-v1.1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-eval.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-eval-v1.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-ixora-v1.1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-ixora-v1.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-mek.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.1.dtsi b/arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.1.dtsi
new file mode 100644
index 000000000000..0f77f78f4d96
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.1.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+#include "imx8-apalis-eval.dtsi"
+
+/* Apalis CAN1 */
+&flexcan1 {
+	status = "okay";
+};
+
+/* Apalis CAN2 */
+&flexcan2 {
+	status = "okay";
+};
+
+/* Apalis MMC1 */
+&usdhc2 {
+	status = "okay";
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.2.dtsi b/arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.2.dtsi
new file mode 100644
index 000000000000..f5c6a0164f36
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8-apalis-eval-v1.2.dtsi
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+#include "imx8-apalis-eval.dtsi"
+
+/ {
+	reg_3v3_mmc: regulator-3v3-mmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_mmc>;
+		enable-active-high;
+		gpio = <&lsio_gpio5 19 GPIO_ACTIVE_HIGH>;
+		off-on-delay-us = <100000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_MMC";
+		startup-delay-us = <10000>;
+	};
+
+	reg_3v3_sd: regulator-3v3-sd {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_sd>;
+		enable-active-high;
+		gpio = <&lsio_gpio5 20 GPIO_ACTIVE_HIGH>;
+		off-on-delay-us = <100000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_SD";
+		startup-delay-us = <10000>;
+	};
+
+	reg_can1: regulator-can1 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can1_power>;
+		enable-active-high;
+		gpio = <&lsio_gpio5 22 GPIO_ACTIVE_HIGH>;
+		regulator-name = "5V_SW_CAN1";
+		startup-delay-us = <10000>;
+	};
+
+	reg_can2: regulator-can2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can2_power>;
+		enable-active-high;
+		gpio = <&lsio_gpio5 21 GPIO_ACTIVE_HIGH>;
+		regulator-name = "5V_SW_CAN2";
+		startup-delay-us = <10000>;
+	};
+};
+
+/* Apalis CAN1 */
+&flexcan1 {
+	xceiver-supply = <&reg_can1>;
+	status = "okay";
+};
+
+/* Apalis CAN2 */
+&flexcan2 {
+	xceiver-supply = <&reg_can2>;
+	status = "okay";
+};
+
+/* Apalis I2C1 */
+&i2c2 {
+	status = "okay";
+
+	/* Power/Current Measurement Sensor */
+	hwmon at 40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <5000>;
+	};
+
+	temperature-sensor at 4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+	};
+
+	eeprom at 57 {
+		compatible = "st,24c02", "atmel,24c02";
+		reg = <0x57>;
+	};
+};
+
+/* Apalis MMC1 */
+&usdhc2 {
+	pinctrl-0 = <&pinctrl_usdhc2_4bit>, <&pinctrl_mmc1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2_4bit_100mhz>, <&pinctrl_mmc1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_4bit_200mhz>, <&pinctrl_mmc1_cd>;
+	pinctrl-3 = <&pinctrl_usdhc2_4bit_sleep>, <&pinctrl_mmc1_cd_sleep>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3_mmc>;
+	status = "okay";
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+	vmmc-supply = <&reg_3v3_sd>;
+	status = "okay";
+};
+
+&iomuxc {
+
+	pinctrl_enable_3v3_mmc: enable3v3mmcgrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA4_LSIO_GPIO5_IO19	0x00000021>; /* MXM3_148 */
+	};
+
+	pinctrl_enable_3v3_sd: enable3v3sdgrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA5_LSIO_GPIO5_IO20	0x00000021>; /* MXM3_152 */
+	};
+
+	pinctrl_enable_can1_power: enablecan1powergrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA7_LSIO_GPIO5_IO22	0x00000021>; /* MXM3_158 */
+	};
+
+	pinctrl_enable_can2_power: enablecan2powergrp {
+		fsl,pins = <IMX8QM_USDHC1_DATA6_LSIO_GPIO5_IO21	0x00000021>; /* MXM3_156 */
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8-apalis-eval.dtsi b/arch/arm64/boot/dts/freescale/imx8-apalis-eval.dtsi
index 685d4294f4f1..deecb96a1596 100644
--- a/arch/arm64/boot/dts/freescale/imx8-apalis-eval.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-apalis-eval.dtsi
@@ -35,18 +35,6 @@ &fec1 {
 	status = "okay";
 };
 
-/* Apalis CAN1 */
-&flexcan1 {
-	status = "okay";
-};
-
-/* Apalis CAN2 */
-&flexcan2 {
-	status = "okay";
-};
-
-/* TODO: GPU */
-
 /* Apalis I2C1 */
 &i2c2 {
 	status = "okay";
@@ -132,13 +120,3 @@ &usbotg1 {
 };
 
 /* TODO: Apalis USBH4 SuperSpeed */
-
-/* Apalis MMC1 */
-&usdhc2 {
-	status = "okay";
-};
-
-/* Apalis SD1 */
-&usdhc3 {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis-eval-v1.2.dts b/arch/arm64/boot/dts/freescale/imx8qm-apalis-eval-v1.2.dts
new file mode 100644
index 000000000000..8466a8204ed0
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis-eval-v1.2.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qm-apalis.dtsi"
+#include "imx8-apalis-eval-v1.2.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX8QM/QP on Apalis Evaluation Board V1.2";
+	compatible = "toradex,apalis-imx8-eval-v1.2",
+		     "toradex,apalis-imx8",
+		     "fsl,imx8qm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis-eval.dts b/arch/arm64/boot/dts/freescale/imx8qm-apalis-eval.dts
index 5ab0921eb599..b0ebf6d05450 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-apalis-eval.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis-eval.dts
@@ -6,7 +6,7 @@
 /dts-v1/;
 
 #include "imx8qm-apalis.dtsi"
-#include "imx8-apalis-eval.dtsi"
+#include "imx8-apalis-eval-v1.1.dtsi"
 
 / {
 	model = "Toradex Apalis iMX8QM/QP on Apalis Evaluation Board";
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval-v1.2.dts b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval-v1.2.dts
new file mode 100644
index 000000000000..92c0ae0c0337
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval-v1.2.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8qm-apalis-v1.1.dtsi"
+#include "imx8-apalis-eval-v1.2.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX8QM V1.1 on Apalis Evaluation Board V1.2";
+	compatible = "toradex,apalis-imx8-v1.1-eval-v1.2",
+		     "toradex,apalis-imx8-v1.1",
+		     "fsl,imx8qm";
+};
+
+/* Apalis MMC1 */
+&usdhc2 {
+	/delete-property/ no-1-8-v;
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+	/delete-property/ no-1-8-v;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval.dts b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval.dts
index c8ff75831556..c998e542f93c 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-apalis-v1.1-eval.dts
@@ -6,7 +6,7 @@
 /dts-v1/;
 
 #include "imx8qm-apalis-v1.1.dtsi"
-#include "imx8-apalis-eval.dtsi"
+#include "imx8-apalis-eval-v1.1.dtsi"
 
 / {
 	model = "Toradex Apalis iMX8QM V1.1 on Apalis Evaluation Board";
-- 
2.39.2

More information about the linux-arm-kernel mailing list