[PATCH v2 3/3] arm64: dts: mediatek: Add device tree for MT8365-based Pumpkin i350
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Tue Jan 23 05:53:58 PST 2024
Il 25/10/23 23:03, Laurent Pinchart ha scritto:
> Add a minimal device tree for the Genio i350 Pumpkin development board,
> which is based on a MediaTek MT8365.
>
> The device tree is based on an initial version by Fabien Parent Based
> written against the MediaTek BSP kernel ([1]). It has been cleaned up,
> some features have been added (GPIO LEDs, ethernet), and some features
> removed (audio, camera, display and dual-role USB). Those features will
> be added back once the corresponding DT bindings and/or drivers become
> available in the upstream kernel.
>
> [1] https://gitlab.com/mediatek/aiot/bsp/linux/-/blob/mtk-v5.15-dev/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts
>
> Co-developed-by: Fabien Parent <fparent at baylibre.com>
> Signed-off-by: Fabien Parent <fparent at baylibre.com>
> Co-developed-by: Paul Elder <paul.elder at ideasonboard.com>
> Signed-off-by: Paul Elder <paul.elder at ideasonboard.com>
> Signed-off-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> ---
> Changes since v1:
>
> - Drop mmc2 alias
> - Reorder properties of i2c, mmc and usb nodes
>
> Changes compared to the BSP version:
>
> - Add ethernet controller
> - Add GPIO LEDs
> - Add reserved memory region for BL31
> - Update board model and compatible
> - Rename enable-sdio-wakeup to wakeup-source
> - Drop audio support
> - Drop display support
> - Drop dual role USB support
> - Don't use underscores in node names
> - Normalize pinmux node names
> - Remove unneeded labels
> - Drop unneeded always-on
> - Drop unused pinmux nodes
> - Drop camera GPIO hog
> - Update copyright
> - Fix formatting
> - Sort alphabetically
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> .../boot/dts/mediatek/mt8365-pumpkin.dts | 541 ++++++++++++++++++
> 2 files changed, 542 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index c99c3372a4b5..bbc232bdadc4 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -53,4 +53,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-pumpkin.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts
> new file mode 100644
> index 000000000000..9c75294c9889
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-pumpkin.dts
> @@ -0,0 +1,541 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2021 BayLibre, SAS.
> + * Copyright (c) 2023 Ideas on Board Oy
> + *
> + * Author: Fabien Parent <fparent at baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
> +
> +#include "mt8365.dtsi"
> +#include "mt6357.dtsi"
> +
> +/ {
> + model = "OLogic Pumpkin i350 EVK";
> + compatible = "ologic,pumpkin-i350", "mediatek,mt8365";
> +
> + aliases {
> + ethernet0 = ðernet_usb;
> + mmc0 = &mmc0;
> + mmc1 = &mmc1;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:921600n8";
> + };
> +
> + firmware {
> + optee {
> + compatible = "linaro,optee-tz";
> + method = "smc";
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-red {
> + gpios = <&gpio_exp 12 GPIO_ACTIVE_HIGH>;
> + color = <LED_COLOR_ID_RED>;
> + function = LED_FUNCTION_HEARTBEAT;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led-green {
> + gpios = <&gpio_exp 13 GPIO_ACTIVE_HIGH>;
> + color = <LED_COLOR_ID_GREEN>;
> + default-state = "off";
> + };
> + };
> +
> + memory at 40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
> + secmon at 43000000 {
> + no-map;
> + reg = <0 0x43000000 0 0x30000>;
reg first, no-map last.
> + };
> +
> + /*
> + * 12 MiB reserved for OP-TEE (BL32)
> + * +-----------------------+ 0x43e0_0000
> + * | SHMEM 2MiB |
> + * +-----------------------+ 0x43c0_0000
> + * | | TA_RAM 8MiB |
> + * + TZDRAM +--------------+ 0x4340_0000
> + * | | TEE_RAM 2MiB |
> + * +-----------------------+ 0x4320_0000
> + */
> + optee at 43200000 {
> + no-map;
> + reg = <0 0x43200000 0 0x00c00000>;
same here.
> + };
> + };
> +
> + usb_otg_vbus: usb-otg-vbus-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&pio 25 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&cpu0 {
> + proc-supply = <&mt6357_vproc_reg>;
> + sram-supply = <&mt6357_vsram_proc_reg>;
> +};
> +
> +&cpu1 {
> + proc-supply = <&mt6357_vproc_reg>;
> + sram-supply = <&mt6357_vsram_proc_reg>;
> +};
> +
> +&cpu2 {
> + proc-supply = <&mt6357_vproc_reg>;
> + sram-supply = <&mt6357_vsram_proc_reg>;
> +};
> +
> +&cpu3 {
> + proc-supply = <&mt6357_vproc_reg>;
> + sram-supply = <&mt6357_vsram_proc_reg>;
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> +
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> +
> + status = "okay";
> +
> + gpio_exp: gpio at 20 {
> + compatible = "ti,tca6416";
> + reg = <0x20>;
> + reset-gpios = <&pio 78 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&tca6416_pins>;
> +
> + gpio-controller;
Please check Documentation/devicetree/bindings/dts-coding-style.rst
> + #gpio-cells = <2>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> +
> + status = "okay";
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> +
> + status = "okay";
> +};
> +
> +&keypad {
> + status = "okay";
status goes last.
Please check Documentation/devicetree/bindings/dts-coding-style.rst
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&keypad_pins>;
> +
> + keypad,num-rows = <2>;
> + keypad,num-columns = <1>;
> + mediatek,debounce-us = <32000>;
> + mediatek,double-keys;
> +
> + linux,keymap = <MATRIX_KEY(0x00, 0x00, KEY_VOLUMEDOWN)
> + MATRIX_KEY(0x01, 0x00, KEY_VOLUMEUP)>;
> +};
> +
> +/* eMMC */
> +&mmc0 {
> + bus-width = <8>;
> + max-frequency = <200000000>;
> +
> + cap-mmc-highspeed;
> + cap-mmc-hw-reset;
> + hs400-ds-delay = <0x12012>;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + no-sd;
> + no-sdio;
> + non-removable;
Please order by name.
> +
> + vmmc-supply = <&mt6357_vemc_reg>;
> + vqmmc-supply = <&mt6357_vio18_reg>;
> +
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc0_pins_default>;
> + pinctrl-1 = <&mmc0_pins_uhs>;
> +
> + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
assigned clocks and clock parents go first.
> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>;
> +
> + status = "okay";
> +};
> +
> +/* SD card connector */
> +&mmc1 {
> + bus-width = <4>;
> + max-frequency = <200000000>;
> +
> + cap-sd-highspeed;
> + cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>;
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
Please order by name.
> +
> + vmmc-supply = <&mt6357_vmch_reg>;
> + vqmmc-supply = <&mt6357_vmc_reg>;
> +
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc1_pins_default>;
> + pinctrl-1 = <&mmc1_pins_uhs>;
> +
> + status = "okay";
> +};
> +
> +/* WiFi module */
> +&mmc2 {
> + bus-width = <4>;
> + max-frequency = <200000000>;
> +
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + wakeup-source;
> + hs400-ds-delay = <0x12012>;
Please order by name.
> + keep-power-in-suspend;
> + non-removable;
> + sd-uhs-sdr104;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> +
> + vmmc-supply = <&mt6357_vemc_reg>;
> + vqmmc-supply = <&mt6357_vio18_reg>;
> +
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc2_pins_default>;
> + pinctrl-1 = <&mmc2_pins_uhs>;
> +
> + assigned-clocks = <&topckgen CLK_TOP_MSDC50_2_SEL>;
> + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>;
> +
> + status = "okay";
> +};
> +
> +&mt6357_pmic {
> + interrupt-parent = <&pio>;
> + interrupts = <145 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +};
> +
> +&pio {
> + i2c0_pins: i2c0-pins {
> + pins {
> + pinmux = <MT8365_PIN_57_SDA0__FUNC_SDA0_0>,
> + <MT8365_PIN_58_SCL0__FUNC_SCL0_0>;
> + mediatek,pull-up-adv = <3>;
> + mediatek,drive-strength-adv = <00>;
I don't know what 00 is here, and it's not a valid drive strength value in uA.
Valid values are 125, 250, 500 and 1000 microamps.
P.S.: Here and everywhere else.
> + bias-pull-up;
> + };
> + };
> +
> +
..snip..
> + mmc0_pins_uhs: mmc0-uhs-pins{
> + clk-pins {
> + pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>;
> + drive-strength = <MTK_DRIVE_10mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + cmd-dat-pins {
> + pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
> + <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
> + <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
> + <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
> + <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
> + <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
> + <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
> + <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
> + <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_10mA>;
There's no need to use MTK_DRIVE_xxxx definitions, as they're really just defining
the same number that you can just clearly write.
In this case, it is
drive-strength = <10>;
please change it here and everywhere else.
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + ds-pins {
> + pinmux = <MT8365_PIN_104_MSDC0_DSL__FUNC_MSDC0_DSL>;
> + drive-strength = <MTK_DRIVE_10mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + rst-pins {
> + pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>;
> + drive-strength = <MTK_DRIVE_10mA>;
> + bias-pull-up;
> + };
> + };
> +
..snip..
> +
> +&usb_host {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vusb33-supply = <&mt6357_vusb33_reg>;
> +
> + status = "okay";
> +
> + hub at 2 {
> + reg = <2>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet_usb: ethernet at 1 {
Can you please explain why you need this node on a fully discoverable bus?
Isn't it enough to just let USB auto enumerate this device at boot?
> + compatible = "usb424,ec00";
> + reg = <1>;
> + };
> + };
> +};
Cheers,
Angelo
More information about the linux-arm-kernel
mailing list