[PATCH v2 5/5] arm64: dts: ti: hummingboard-t: add descriptions for m.2 pci-e and usb-3

[Andrew Davis]

On 1/12/24 11:12 AM, Josua Mayer wrote:
> HummingBoard-T features two M.2 connectors labeled "M1" and "M2".
> The single SerDes lane of the SoC can be routed to either M1 pci-e
> signals, or M2 usb-3 signals by a gpio-controlled mux.
> 
> Add dedicated dts for each configuration.
> - k3-am642-hummingboard-t.dts enables neither configuration
> - k3-am642-hummingboard-t-pcie.dts (new)
>    configures serdes mux and pci-e controller for M1
> - k3-am642-hummingboard-t-usb3.dts (new)
>    configures serdes mux and usb-3 controller for M2
> 
> Signed-off-by: Josua Mayer <josua at solid-run.com>
> ---
>   arch/arm64/boot/dts/ti/Makefile                    |  2 ++
>   .../boot/dts/ti/k3-am642-hummingboard-t-pcie.dts   | 31 ++++++++++++++++++
>   .../boot/dts/ti/k3-am642-hummingboard-t-usb3.dts   | 37 ++++++++++++++++++++++
>   3 files changed, 70 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 041c3b71155e..0e408555edf1 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -33,6 +33,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb
>   # Boards with AM64x SoC
>   dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
>   dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t-pcie.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t-usb3.dtb
>   dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
>   dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
>   dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl.dtb
> diff --git a/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-pcie.dts b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-pcie.dts
> new file mode 100644
> index 000000000000..5ba0029fcfb9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-pcie.dts
> @@ -0,0 +1,31 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Josua Mayer <josua at solid-run.com>
> + *
> + * DTS for SolidRun AM642 HummingBoard-T,
> + * running on Cortex A53, with PCI-E.
> + *
> + */
> +
> +#include "k3-am642-hummingboard-t.dts"

Avoid including .dts files, if this file is for an option that
can be chosen (PCIe vs USB3), then it should be a DT overlay.

> +#include "k3-serdes.h"
> +
> +/ {
> +	model = "SolidRun AM642 HummingBoard-T with PCI-E";
> +};
> +
> +&pcie0_rc {
> +	status = "okay";

If PCIe is only available here when using this add-on then
all of the node data should be in this add-on file.

Andrew

> +};
> +
> +&serdes0_link {
> +	cdns,phy-type = <PHY_TYPE_PCIE>;
> +};
> +
> +&serdes_ln_ctrl {
> +	idle-states = <AM64_SERDES0_LANE0_PCIE0>;
> +};
> +
> +&serdes_mux {
> +	idle-state = <1>;
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-usb3.dts b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-usb3.dts
> new file mode 100644
> index 000000000000..12b0fedcd2bc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t-usb3.dts
> @@ -0,0 +1,37 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Josua Mayer <josua at solid-run.com>
> + *
> + * DTS for SolidRun AM642 HummingBoard-T,
> + * running on Cortex A53, with USB-3.1 Gen 1.
> + *
> + */
> +
> +#include "k3-am642-hummingboard-t.dts"
> +#include "k3-serdes.h"
> +
> +/ {
> +	model = "SolidRun AM642 HummingBoard-T with USB-3.1 Gen 1";
> +};
> +
> +&serdes0_link {
> +	cdns,phy-type = <PHY_TYPE_USB3>;
> +};
> +
> +&serdes_ln_ctrl {
> +	idle-states = <AM64_SERDES0_LANE0_USB>;
> +};
> +
> +&serdes_mux {
> +	idle-state = <0>;
> +};
> +
> +&usbss0 {
> +	/delete-property/ ti,usb2-only;
> +};
> +
> +&usb0 {
> +	maximum-speed = "super-speed";
> +	phys = <&serdes0_link>;
> +	phy-names = "cdns3,usb3-phy";
> +};
>