[PATCH v2 0/5] arm64: dts: add description for solidrun am642 som and hummingboard evb

[Josua Mayer]

This series adds DT bindings and dts descriptions for SolidRun AM642
based SoM and Hummingboard EVB.

Additionally a commit from downstream vendor kernel are included,
enhancing support for pru based ethernet.
I wasn't sure how to properly annotate it in commit description /
signed-off area ...:

1. add description for "Industrial Ethernet Peripherals" (IEP) to am64
   https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/commit/arch/arm64/boot/dts/ti/k3-am64-main.dtsi?h=ti-linux-6.1.y-cicd&id=5afb73d82a014b59462162d960b350b8c58e5ae6
   IEP is already supported in-tree by a driver, and used in
   k3-am65-main.dtsi.

Unfortunately dtbs_check reported many problems, I put some remarks:

- 'mux-controller' does not match any of the regexes
  The expectation seems to be that a mux-controller at minimum has an
  address, something to put behind an @. However this is a gpio mux, not
  sure how to name it better.

- unevaluated properties: interrupts, interrupt-parent
  sensors and flash yaml are missing interrupt descriptions, but these
  parts definitely have an interrupt signal in this solidrun board.

- icssg1-eth dmas is too long
  It is caused by definint 12 dmas, when ti,icssg-prueth.yaml specifies a
  maximum of 10. The pru ethernet on am64 mostly identical to am65 - see
  e.g. arch/arm64/boot/dts/ti/k3-am654-idk.dtso which also defines 12 dma.
  I cannot fix it because unsure what is the purpose of last two dmas.

- wrong names for pinctrl nodes
  Other TI DTSs consistently end with *-pins-default. Should a different
  naming convention be used?

- cdns,phy-type required property
  inherited from k3-am64-main.dtsi
  there is a PHY_NONE value in dt-bindings/phy/phy.h,
  but not allowed in phy-cadence-torrent.yaml

Signed-off-by: Josua Mayer <josua at solid-run.com>
---
Changes in v2:
- reordered patchset to drop separate patch adding iep handle to som
- moved dtbs_check warnings to cover letter
- converted abracon abx80x rtc bindings to yaml
- updated dts:
  - remove unnecessary status properties
  - changed non-generic node names
  - use color property for led descriptions,
    they have no default function on evaluation board
  - drop earlycon bootargs from chosen node
  (reported by Krzysztof Kozlowski <krzysztof.kozlowski+dt at linaro.org>)
- converted charger node to comment, part not assembled, has no bindings
- picked up acked-by on board bindings patch
- Link to v1: https://lore.kernel.org/r/20240103-add-am64-som-v1-0-dda1f9227aef@solid-run.com

---
Josua Mayer (4):
      dt-bindings: arm: ti: Add bindings for SolidRun AM642 HummingBoard-T
      dt-bindings: rtc: abx80x: convert to yaml
      arm64: dts: add description for solidrun am642 som and evaluation board
      arm64: dts: ti: hummingboard-t: add descriptions for m.2 pci-e and usb-3

Suman Anna (1):
      arm64: dts: ti: k3-am64-main: Add ICSSG IEP nodes

 Documentation/devicetree/bindings/arm/ti/k3.yaml   |   7 +
 .../devicetree/bindings/rtc/abracon,abx80x.txt     |  31 -
 .../devicetree/bindings/rtc/abracon,abx80x.yaml    |  56 ++
 arch/arm64/boot/dts/ti/Makefile                    |   3 +
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi           |  24 +
 .../boot/dts/ti/k3-am642-hummingboard-t-pcie.dts   |  31 +
 .../boot/dts/ti/k3-am642-hummingboard-t-usb3.dts   |  37 ++
 arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts | 326 +++++++++++
 arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi        | 638 +++++++++++++++++++++
 9 files changed, 1122 insertions(+), 31 deletions(-)
---
base-commit: 861deac3b092f37b2c5e6871732f3e11486f7082
change-id: 20240101-add-am64-som-51a1ca47edf3

Sincerely,
-- 
Josua Mayer <josua at solid-run.com>