[PATCH v4 5/5] arm64: dts: mediatek: mt8365: Add support for camera

[Julien Stephan]

Add base support for cameras for mt8365 platforms. This requires nodes
for the sensor interface, camsv, and CSI receivers.

Signed-off-by: Julien Stephan <jstephan at baylibre.com>
---
 arch/arm64/boot/dts/mediatek/mt8365.dtsi | 128 +++++++++++++++++++++++
 1 file changed, 128 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
index 24581f7410aa..9059b2f83b83 100644
--- a/arch/arm64/boot/dts/mediatek/mt8365.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -10,6 +10,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/phy/phy.h>
 #include <dt-bindings/power/mediatek,mt8365-power.h>
+#include <dt-bindings/memory/mediatek,mt8365-larb-port.h>
 
 / {
 	compatible = "mediatek,mt8365";
@@ -703,6 +704,133 @@ ethernet: ethernet at 112a0000 {
 			status = "disabled";
 		};
 
+		camsv1: camsv at 15050000 {
+			compatible = "mediatek,mt8365-camsv";
+			reg = <0 0x15050000 0 0x0040>,
+			      <0 0x15050208 0 0x0020>,
+			      <0 0x15050400 0 0x0100>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&camsys CLK_CAM>,
+				 <&camsys CLK_CAMTG>,
+				 <&camsys CLK_CAMSV0>;
+			clock-names = "cam", "camtg", "camsv";
+			iommus = <&iommu M4U_PORT_CAM_IMGO>;
+			mediatek,larb = <&larb2>;
+			power-domains = <&spm MT8365_POWER_DOMAIN_CAM>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port at 0 {
+					reg = <0>;
+					camsv1_endpoint: endpoint {
+						remote-endpoint =
+							<&seninf_camsv1_endpoint>;
+					};
+				};
+			};
+		};
+
+		camsv2: camsv at 15050800 {
+			compatible = "mediatek,mt8365-camsv";
+			reg = <0 0x15050800 0 0x0040>,
+			      <0 0x15050228 0 0x0020>,
+			      <0 0x15050C00 0 0x0100>;
+			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&camsys CLK_CAM>,
+				 <&camsys CLK_CAMTG>,
+				 <&camsys CLK_CAMSV1>;
+			clock-names = "cam", "camtg", "camsv";
+			iommus = <&iommu M4U_PORT_CAM_IMGO>;
+
+			mediatek,larb = <&larb2>;
+			power-domains = <&spm MT8365_POWER_DOMAIN_CAM>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port at 0 {
+					reg = <0>;
+					camsv2_endpoint: endpoint {
+						remote-endpoint =
+							<&seninf_camsv2_endpoint>;
+					};
+				};
+			};
+		};
+
+		seninf: seninf at 15040000 {
+			compatible = "mediatek,mt8365-seninf";
+			reg = <0 0x15040000 0 0x6000>;
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&camsys CLK_CAM_SENIF>,
+				 <&topckgen CLK_TOP_SENIF_SEL>;
+			clock-names = "camsys", "top_mux";
+
+			power-domains = <&spm MT8365_POWER_DOMAIN_CAM>;
+
+			phys = <&mipi_csi0 PHY_TYPE_DPHY>, <&mipi_csi1>;
+			phy-names = "csi0", "csi1";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 0 {
+					reg = <0>;
+				};
+
+				port at 1 {
+					reg = <1>;
+				};
+
+				port at 2 {
+					reg = <2>;
+				};
+
+				port at 3 {
+					reg = <3>;
+				};
+
+				port at 4 {
+					reg = <4>;
+					seninf_camsv1_endpoint: endpoint {
+						remote-endpoint =
+							<&camsv1_endpoint>;
+					};
+				};
+
+				port at 5 {
+					reg = <5>;
+					seninf_camsv2_endpoint: endpoint {
+						remote-endpoint =
+							<&camsv2_endpoint>;
+					};
+				};
+			};
+		};
+
+		mipi_csi0: mipi-csi0 at 11c10000 {
+			compatible = "mediatek,mt8365-csi-rx";
+			reg = <0 0x11C10000 0 0x2000>;
+			status = "disabled";
+			num-lanes = <4>;
+			#phy-cells = <1>;
+		};
+
+		mipi_csi1: mipi-csi1 at 11c12000 {
+			compatible = "mediatek,mt8365-csi-rx";
+			reg = <0 0x11C12000 0 0x2000>;
+			phy-type = <PHY_TYPE_DPHY>;
+			status = "disabled";
+			num-lanes = <4>;
+			#phy-cells = <0>;
+		};
+
 		u3phy: t-phy at 11cc0000 {
 			compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
 			#address-cells = <1>;
-- 
2.43.0