[PATCH 02/14] arm64: zynqmp: Add output-enable pins to SOMs

[Michal Simek]

From: Neal Frager <neal.frager at amd.com>

Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.

Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.

In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio at ff0a000038 && \
  gpio toggle gpio at ff0a000038

Signed-off-by: Neal Frager <neal.frager at amd.com>
Signed-off-by: Michal Simek <michal.simek at amd.com>
---

 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso | 5 +++++
 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso | 5 +++++
 2 files changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
index 92f4190d564d..e7940067ff3c 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
@@ -185,6 +185,7 @@ conf-rx {
 		conf-tx {
 			pins = "MIO36";
 			bias-disable;
+			output-enable;
 		};
 
 		mux {
@@ -236,6 +237,7 @@ conf-rx {
 		conf-bootstrap {
 			pins = "MIO71", "MIO73", "MIO75";
 			bias-disable;
+			output-enable;
 			low-power-disable;
 		};
 
@@ -243,6 +245,7 @@ conf-tx {
 			pins = "MIO64", "MIO65", "MIO66",
 				"MIO67", "MIO68", "MIO69";
 			bias-disable;
+			output-enable;
 			low-power-enable;
 		};
 
@@ -251,6 +254,7 @@ conf-mdio {
 			slew-rate = <SLEW_RATE_SLOW>;
 			power-source = <IO_STANDARD_LVCMOS18>;
 			bias-disable;
+			output-enable;
 		};
 
 		mux-mdio {
@@ -281,6 +285,7 @@ conf-tx {
 			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
 			"MIO60", "MIO61", "MIO62", "MIO63";
 			bias-disable;
+			output-enable;
 			drive-strength = <4>;
 			slew-rate = <SLEW_RATE_SLOW>;
 		};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
index f88b71f5b07a..f72312926299 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
@@ -168,6 +168,7 @@ conf-rx {
 		conf-tx {
 			pins = "MIO36";
 			bias-disable;
+			output-enable;
 		};
 
 		mux {
@@ -219,6 +220,7 @@ conf-rx {
 		conf-bootstrap {
 			pins = "MIO71", "MIO73", "MIO75";
 			bias-disable;
+			output-enable;
 			low-power-disable;
 		};
 
@@ -226,6 +228,7 @@ conf-tx {
 			pins = "MIO64", "MIO65", "MIO66",
 				"MIO67", "MIO68", "MIO69";
 			bias-disable;
+			output-enable;
 			low-power-enable;
 		};
 
@@ -234,6 +237,7 @@ conf-mdio {
 			slew-rate = <SLEW_RATE_SLOW>;
 			power-source = <IO_STANDARD_LVCMOS18>;
 			bias-disable;
+			output-enable;
 		};
 
 		mux-mdio {
@@ -264,6 +268,7 @@ conf-tx {
 			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
 			"MIO60", "MIO61", "MIO62", "MIO63";
 			bias-disable;
+			output-enable;
 			drive-strength = <4>;
 			slew-rate = <SLEW_RATE_SLOW>;
 		};
-- 
2.36.1