[PATCH v3 4/4] arm64: dts: rockchip: Add devicetree for Pine64 PineTab2
Ondřej Jirman
megi at xff.cz
Tue Jan 2 10:07:56 PST 2024
Hello Manuel,
see below...
On Tue, Jan 02, 2024 at 05:15:47PM +0100, Manuel Traut wrote:
> From: Alexander Warnecke <awarnecke002 at hotmail.com>
>
> [...]
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi
> new file mode 100644
> index 000000000000..5d895628406b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi
> @@ -0,0 +1,959 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include <dt-bindings/usb/pd.h>
> +#include "rk3566.dtsi"
> +
> +/ {
> + chassis-type = "tablet";
> +
> + aliases {
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc0;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <25>;
> +
> + button-vol-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + press-threshold-microvolt = <297500>;
> + };
> +
> + button-vol-down {
> + label = "Volume Down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + press-threshold-microvolt = <1750>;
> + };
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm4 0 25000 0>;
> + brightness-levels = <20 220>;
> + num-interpolated-steps = <200>;
Does this linear brightness -> PWM duty cycle mapping lead to linear
relationship between brighntess level and subjective brightness on this HW?
I doubt it a bit...
> + default-brightness-level = <100>;
> + power-supply = <&vcc_sys>;
> + };
> +
> + battery: battery {
> + compatible = "simple-battery";
> + charge-full-design-microamp-hours = <6000000>;
> + charge-term-current-microamp = <300000>;
> + constant-charge-current-max-microamp = <2000000>;
> + constant-charge-voltage-max-microvolt = <4300000>;
> + voltage-max-design-microvolt = <4350000>;
> + voltage-min-design-microvolt = <3400000>;
> +
> + ocv-capacity-celsius = <20>;
> + ocv-capacity-table-0 = <4322000 100>, <4250000 95>, <4192000 90>, <4136000 85>,
> + <4080000 80>, <4022000 75>, <3972000 70>, <3928000 65>,
> + <3885000 60>, <3833000 55>, <3798000 50>, <3780000 45>,
> + <3776000 40>, <3773000 35>, <3755000 30>, <3706000 25>,
> + <3640000 20>, <3589000 15>, <3535000 10>, <3492000 5>,
> + <3400000 0>;
> + };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&kb_id_det>;
> +
> + tablet-mode-switch {
> + debounce-interval = <20>;
> + gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_HIGH>;
> + label = "Tablet Mode";
> + linux,input-type = <EV_SW>;
> + linux,code = <SW_TABLET_MODE>;
> + };
> + };
> +
> + hdmi-con {
hdmi-connector
> + compatible = "hdmi-connector";
> + type = "d";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
Spurious newline ^
> + pinctrl-names = "default";
> + pinctrl-0 = <&flash_led_en_h>;
> +
> + led-0 {
> + gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> + color = <LED_COLOR_ID_WHITE>;
> + function = LED_FUNCTION_FLASH;
> + };
> + };
> +
> + rk817-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_det_l>;
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "rk817_ext";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones",
> + "Speaker", "Internal Speakers";
> +
> + simple-audio-card,routing =
> + "MICR", "Mic Jack",
> + "Headphones", "HPOL",
> + "Headphones", "HPOR",
> + "Internal Speakers", "Speaker Amplifier OUTL",
> + "Internal Speakers", "Speaker Amplifier OUTR",
> + "Speaker Amplifier INL", "HPOL",
> + "Speaker Amplifier INR", "HPOR";
> + simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;
> + simple-audio-card,aux-devs = <&speaker_amp>;
> + simple-audio-card,pin-switches = "Internal Speakers";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1_8ch>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&rk817>;
> + };
> + };
> +
> + speaker_amp: speaker-amplifier {
> + compatible = "simple-audio-amplifier";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spk_ctl>;
> + enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> + sound-name-prefix = "Speaker Amplifier";
> + VCC-supply = <&vcc_bat>;
> + };
> +
> + vcc_3v3: vcc-3v3 {
Regulator node names shoule end with -regulator suffix. The same applies for
all of the below nodes.
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_3v3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + vcc3v3_minipcie: vcc3v3-minipcie {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_pwren_h>;
> + regulator-name = "vcc3v3_minipcie";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc3v3_sd: vcc3v3-sd {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_pwren_l>;
> + regulator-name = "vcc3v3_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + vcc5v0_usb_host0: vcc5v0-usb-host0 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_host_pwren1_h>;
> + regulator-name = "vcc5v0_usb_host0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v_midu>;
> + };
> +
> + vcc5v0_usb_host2: vcc5v0-usb-host2 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_host_pwren2_h>;
> + regulator-name = "vcc5v0_usb_host2";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v_midu>;
> + };
> +
> + vcc_bat: vcc-bat {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_bat";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcc_sys: vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_bat>;
> + };
> +
> + vdd1v2_dvp: vdd1v2-dvp {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd1v2_dvp";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + vin-supply = <&vcc_3v3>;
> + /*enable-supply = <&vcc2v8_dvp>;*/
There's no such property. Delete this commented out line.
> + };
> +};
> +
> +&combphy1 {
> + status = "okay";
> +};
> +
> +&combphy2 {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cru {
> + assigned-clocks = <&pmucru CLK_RTC_32K>, <&cru PLL_GPLL>,
> + <&pmucru PLL_PPLL>, <&cru PLL_VPLL>;
> + assigned-clock-rates = <32768>, <1200000000>, <200000000>, <500000000>;
> + assigned-clock-parents = <&pmucru CLK_RTC32K_FRAC>;
> +};
> +
> +&csi_dphy {
> + status = "okay";
> +};
> +
> +&dsi0 {
> + status = "okay";
> + clock-master;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + lcd: panel at 0 {
> + compatible = "boe,th101mb31ig002-28a";
> + reg = <0>;
> + backlight = <&backlight>;
> + enable-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcd_pwren_h &lcd0_rst_l>;
Re lcd0_rst_l:
It's a bit weird conceptually to reference from dtsi something that's only
declared in dts that includes the dtsi. Maybe move pinctrl-* properties
to dts &lcd, too...
> + rotation = <90>;
> + power-supply = <&vcc_3v3>;
> +
> + port at 0 {
> + panel_in_dsi: endpoint at 0 {
> + remote-endpoint = <&dsi0_out_con>;
> + };
> + };
> + };
> +};
> +
> +&dsi0_in {
> + dsi0_in_vp1: endpoint {
> + remote-endpoint = <&vp1_out_dsi0>;
> + };
> +};
> +
> +&dsi0_out {
> + dsi0_out_con: endpoint {
> + remote-endpoint = <&panel_in_dsi>;
> + };
> +};
> +
> +&dsi_dphy0 {
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu_npu>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + avdd-0v9-supply = <&vdda_0v9_p>;
> + avdd-1v8-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&hdmi_in {
> + hdmi_in_vp0: endpoint {
> + remote-endpoint = <&vp0_out_hdmi>;
> + };
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + vdd_cpu: regulator at 1c {
> + compatible = "tcs,tcs4525";
> + reg = <0x1c>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-ramp-delay = <2300>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + rk817: pmic at 20 {
> + compatible = "rockchip,rk817";
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> + assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> + clock-names = "mclk";
> + clocks = <&cru I2S1_MCLKOUT_TX>;
> + clock-output-names = "rk808-clkout1", "rk808-clkout2";
> + #clock-cells = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
> + rockchip,system-power-controller;
> + #sound-dai-cells = <0>;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sys>;
> + vcc2-supply = <&vcc_sys>;
> + vcc3-supply = <&vcc_sys>;
> + vcc4-supply = <&vcc_sys>;
> + vcc5-supply = <&vcc_sys>;
> + vcc6-supply = <&vcc_sys>;
> + vcc7-supply = <&vcc_sys>;
> + vcc8-supply = <&vcc_sys>;
> + vcc9-supply = <&vcc5v_midu>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_logic";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu_npu: DCDC_REG2 {
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vdd_gpu_npu";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc_ddr";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc3v3_sys: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-initial-mode = <0x2>;
> + regulator-name = "vcc3v3_sys";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcca1v8_pmu: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcca1v8_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vdda_0v9_p: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda_0v9_p";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdda0v9_pmu: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdda0v9_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vccio_acodec: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_acodec";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio_sd";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_pmu: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pmu";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc1v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc2v8_dvp: LDO_REG9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-name = "vcc2v8_dvp";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc5v_midu: BOOST {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "boost";
> + regulator-state-mem {
> + regulator-off-in-suspend;
I guess this prevents remote USB wakeup by USB devices. Like wakeup via USB
keyboard. Probably not a bad thing, though.
> + };
> + };
> +
> + vbus: OTG_SWITCH {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "otg_switch";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> +
> + charger {
> + monitored-battery = <&battery>;
> + rockchip,resistor-sense-micro-ohms = <10000>;
> + rockchip,sleep-enter-current-microamp = <300000>;
> + rockchip,sleep-filter-current-microamp = <100000>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen at 5d {
> + compatible = "goodix,gt911";
> + reg = <0x5d>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PB0 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&tp_int_l_pmuio2>, <&tp_rst_l_pmuio2>;
> + AVDD28-supply = <&vcc3v3_pmu>;
> + VDDIO-supply = <&vcca1v8_pmu>;
> + irq-gpios = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + pinctrl-0 = <&i2c2m1_xfer>;
> + status = "okay";
> +
> + vcm at c {
> + compatible = "dongwoon,dw9714";
> + reg = <0x0c>;
> + vcc-supply = <&vcc1v8_dvp>;
> + };
> +
> + camera at 36 {
> + compatible = "ovti,ov5648";
> + reg = <0x36>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&camerab_pdn_l &camerab_rst_l>;
> +
> + clocks = <&cru CLK_CIF_OUT>;
> + assigned-clocks = <&cru CLK_CIF_OUT>;
> + assigned-clock-rates = <24000000>;
> +
> + avdd-supply = <&vcc2v8_dvp>;
> + dvdd-supply = <&vdd1v2_dvp>;
> + dovdd-supply = <&vcc1v8_dvp>;
> + powerdown-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpio4 RK_PB1 GPIO_ACTIVE_LOW>;
> +
> + port {
> + endpoint {
> + data-lanes = <1 2>;
> + remote-endpoint = <0>;
> + link-frequencies = /bits/ 64 <210000000 168000000>;
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + accelerometer at 18 {
> + compatible = "silan,sc7a20";
> + reg = <0x18>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gsensor_int_l>;
> + st,drdy-int-pin = <1>;
> + vdd-supply = <&vcc_1v8>;
> + vddio-supply = <&vcc_1v8>;
> + mount-matrix = "1", "0", "0",
> + "0", "0", "1",
> + "0", "1", "0";
> + };
> +};
> +
> +&i2s0_8ch {
> + status = "okay";
> +};
> +
> +&i2s1_8ch {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s1m0_sclktx
> + &i2s1m0_lrcktx
> + &i2s1m0_sdi0
> + &i2s1m0_sdo0>;
> + rockchip,trcm-sync-tx-only;
> + status = "okay";
> +};
> +
> +&pcie2x1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_reset_h>;
> + reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_minipcie>;
> + status = "okay";
> +};
Does it make sense to enable this HW block by default, when it isn't used on
actual HW?
> +&pinctrl {
> + bt {
> + bt_wake_host_h: bt-wake-host-h {
> + rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
^^^ unused
> +
> + camerab {
> + camerab_pdn_l: camerab-pdn-l {
> + rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + camerab_rst_l: camerab-rst-l {
> + rockchip,pins = <4 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + cameraf {
> + cameraf_pdn_l: cameraf-pdn-l {
> + rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + cameraf_rst_l: cameraf-rst-l {
> + rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
^^^ unused
> +
> + flash {
> + flash_led_en_h: flash-led-en-h {
> + rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + fspi {
> + fspi_dual_io_pins: fspi-dual-io-pins {
> + rockchip,pins =
> + /* fspi_clk */
> + <1 RK_PD0 1 &pcfg_pull_none>,
> + /* fspi_cs0n */
> + <1 RK_PD3 1 &pcfg_pull_none>,
> + /* fspi_d0 */
> + <1 RK_PD1 1 &pcfg_pull_none>,
> + /* fspi_d1 */
> + <1 RK_PD2 1 &pcfg_pull_none>;
> + };
> + };
> +
> + gsensor {
> + gsensor_int_l: gsensor-int-l {
> + rockchip,pins = <3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + kb {
> + kb_id_det: kb-id-det {
> + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + lcd {
> + lcd_pwren_h: lcd-pwren-h {
> + rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pcie {
> + pcie_pwren_h: pcie-pwren-h {
> + rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie_reset_h: pcie-reset-h {
> + rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_pwren_l: sdmmc-pwren-l {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sound {
> + hp_det_l: hp-det-l {
> + rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + spk_ctl: spk-ctl {
> + rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + tp {
> + tp_int_l_pmuio2: tp-int-l-pmuio2 {
> + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + tp_rst_l_pmuio2: tp-rst-l-pmuio2 {
> + rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + usbcc_int_l: usbcc-int-l {
> + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
^^^ unused
> + usb_host_pwren1_h: usb-host-pwren1-h {
> + rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + usb_host_pwren2_h: usb-host-pwren2-h {
> + rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wifi {
> + host_wake_wl: host-wake-wl {
> + rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + wifi_pwren: wifi-pwren {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + wifi_wake_host_h: wifi-wake-host-h {
> + rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
^^^ all of this wifi stuff is unused
Also wifi_pwren is not really useful on actual HW. W_VBAT is routed directly
to wifi chip, with wifi_pwren_h signal having no effect: (short via R9664)
https://megous.com/dl/tmp/b499859c1012f969.png
> +};
> +
> +&pmu_io_domains {
> + pmuio1-supply = <&vcc3v3_pmu>;
> + pmuio2-supply = <&vcca1v8_pmu>;
> + vccio1-supply = <&vccio_acodec>;
> + vccio2-supply = <&vcc_1v8>;
> + vccio3-supply = <&vccio_sd>;
> + vccio4-supply = <&vcc_1v8>;
> + vccio5-supply = <&vcc_1v8>;
> + vccio6-supply = <&vcc1v8_dvp>;
> + vccio7-supply = <&vcc_3v3>;
> + status = "okay";
> +};
> +
> +&pwm4 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + no-sdio;
> + no-sd;
> + non-removable;
> + max-frequency = <200000000>;
> + mmc-hs200-1_8v;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_bus8
> + &emmc_clk
> + &emmc_cmd
> + &emmc_datastrobe
> + &emmc_rstnout>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_bus4
> + &sdmmc0_clk
> + &sdmmc0_cmd
> + &sdmmc0_det>;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc3v3_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&sdmmc1 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc1_bus4
> + &sdmmc1_cmd
> + &sdmmc1_clk>;
> + sd-uhs-sdr104;
> + vqmmc-supply = <&vcca1v8_pmu>;
> + status = "okay";
> +};
> +
> +&sfc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&fspi_dual_io_pins>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <24000000>;
That's a bit on the low side. The flash chip should work for all commands up to
80MHz https://megous.com/dl/tmp/b428ad9b85ac4633.png and SGM3157YC6 switch
for the FSPI-CLK should have high enough bandwidth, too.
> + spi-rx-bus-width = <2>;
GD25LQ128E supports quad I/O. Maybe try 4 if it will work.
> + spi-tx-bus-width = <1>;
> + };
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>;
> + rockchip,hw-tshut-polarity = <0>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1m0_xfer
> + &uart1m0_ctsn
> + &uart1m0_rtsn>;
> + status = "okay";
> + uart-has-rtscts;
> +};
Not sure about enabling UART for bluetooth, without having the bluetooth driver
hooked in, somehow. UART will by default pull TX signal high, which may cause
current leakage into gpio/uart pin of the bluetooth chip, if it's not powered up.
Maybe just remove this, until bluetooth is figured out...
kind regards,
o.
More information about the linux-arm-kernel
mailing list