[PATCH V3] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash

[Sinthu Raja]

From: Sinthu Raja <sinthu.raja at ti.com>

AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.

Signed-off-by: Sinthu Raja <sinthu.raja at ti.com>
---

Changes in V3:
Address review comments:
   a. Fix the make dtbs_check error related to ospi pinctrl
   b. Increase the partition 0 size to 1MB and update the following
partitions start address accordingly.

V2: https://lore.kernel.org/linux-arm-kernel/20240219075932.6458-1-sinthu.raja@ti.com/

 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 78 ++++++++++++++++++++++
 1 file changed, 78 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
index 0f4a5da0ebc4..d3e869c250a2 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
@@ -130,6 +130,24 @@ rtos_ipc_memory_region: ipc-memories at a8000000 {
 	};
 };
 
+&wkup_pmx0 {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+			J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+			J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+		>;
+	};
+};
+
 &wkup_pmx2 {
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
 		pinctrl-single,pins = <
@@ -152,6 +170,66 @@ eeprom at 51 {
 	};
 };
 
+&ospi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "ospi.tiboot3";
+				reg = <0x0 0x100000>;
+			};
+
+			partition at 100000 {
+				label = "ospi.tispl";
+				reg = <0x100000 0x200000>;
+			};
+
+			partition at 300000 {
+				label = "ospi.u-boot";
+				reg = <0x300000 0x400000>;
+			};
+
+			partition at 700000 {
+				label = "ospi.env";
+				reg = <0x700000 0x40000>;
+			};
+
+			partition at 740000 {
+				label = "ospi.env.backup";
+				reg = <0x740000 0x40000>;
+			};
+
+			partition at 800000 {
+				label = "ospi.rootfs";
+				reg = <0x800000 0x37c0000>;
+			};
+
+			partition at 3fc0000 {
+				label = "ospi.phypattern";
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+	};
+};
+
 &mailbox0_cluster0 {
 	status = "okay";
 	interrupts = <436>;
-- 
2.34.1