[PATCH 2/2] arm64: dts: ti: k3-j722s-evm: Enable OSPI NOR support

[Vaishnav Achath]

Hi Udit,

On 19/02/24 11:25, Kumar, Udit wrote:
> Hi Vaishnav
> 
> On 2/16/2024 7:25 PM, Vaishnav Achath wrote:
>> J722S EVM has S28HS512T 64 MiB Octal SPI NOR flash connected
>> to the OSPI interface, add support for the flash and describe
>> the partition information as per bootloader.
>>
>> Signed-off-by: Vaishnav Achath <vaishnav.a at ti.com>
>> ---
>>   arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 79 +++++++++++++++++++++++++
>>   1 file changed, 79 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts 
>> b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
>> index 9e12a6e9111f..b1c6499c0c9d 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
>> @@ -169,6 +169,23 @@ J722S_IOPAD(0x015c, PIN_INPUT, 0) /* (AD25) 
>> MDIO0_MDIO */
>>           >;
>>       };
>> +    ospi0_pins_default: ospi0-default-pins {
>> +        pinctrl-single,pins = <
>> +            J722S_IOPAD(0x0000, PIN_OUTPUT, 0) /* (P23) OSPI0_CLK */
>> +            J722S_IOPAD(0x002c, PIN_OUTPUT, 0) /* (M25) OSPI0_CSn0 */
>> +            J722S_IOPAD(0x000c, PIN_INPUT, 0) /* (L25) OSPI0_D0 */
>> +            J722S_IOPAD(0x0010, PIN_INPUT, 0) /* (N24) OSPI0_D1 */
>> +            J722S_IOPAD(0x0014, PIN_INPUT, 0) /* (N25) OSPI0_D2 */
>> +            J722S_IOPAD(0x0018, PIN_INPUT, 0) /* (M24) OSPI0_D3 */
>> +            J722S_IOPAD(0x001c, PIN_INPUT, 0) /* (N21) OSPI0_D4 */
>> +            J722S_IOPAD(0x0020, PIN_INPUT, 0) /* (N22) OSPI0_D5 */
>> +            J722S_IOPAD(0x0024, PIN_INPUT, 0) /* (P21) OSPI0_D6 */
>> +            J722S_IOPAD(0x0028, PIN_INPUT, 0) /* (N20) OSPI0_D7 */
>> +            J722S_IOPAD(0x0008, PIN_INPUT, 0) /* (P22) OSPI0_DQS */
> 
> 
> Could you check, Pin name in comments
> 
> For example, Schematic says L22 is for OSPI0_DQS , but comments says P22
> 
> However offsets are good .

Thanks for the review, I will fix this in the next revision.

> 
>> +        >;
>> +        bootph-all;
>> +    };
>> +
>>       rgmii1_pins_default: rgmii1-default-pins {
>>           pinctrl-single,pins = <
>>               J722S_IOPAD(0x014c, PIN_INPUT, 0) /* (AC25) RGMII1_RD0 */
>> @@ -290,6 +307,68 @@ exp1: gpio at 23 {
>>       };
>>   };
>> +&ospi0 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&ospi0_pins_default>;
>> +    status = "okay";
>> +
>> +    flash at 0 {
>> +        compatible = "jedec,spi-nor";
>> +        reg = <0x0>;
>> +        spi-tx-bus-width = <8>;
>> +        spi-rx-bus-width = <8>;
>> +        spi-max-frequency = <25000000>;
>> +        cdns,tshsl-ns = <60>;
>> +        cdns,tsd2d-ns = <60>;
>> +        cdns,tchsh-ns = <60>;
>> +        cdns,tslch-ns = <60>;
>> +        cdns,read-delay = <4>;
>> +        bootph-all;
>> +
>> +        partitions {
>> +            compatible = "fixed-partitions";
>> +            #address-cells = <1>;
>> +            #size-cells = <1>;
>> +
>> +            partition at 0 {
>> +                label = "ospi.tiboot3";
>> +                reg = <0x00 0x80000>;
>> +            };
> 
> 
> I suggest to keep 1MB to accommodate future size increase
> 

For J722S, the maximum loadable SPL size is 0x7e000, images larger than 
these cannot be loaded by ROM, increasing the size here will not give 
any benefit, planning to keep as-is if there are no objections.

Thanks and Regards,
Vaishnav

>> +
>> +            partition at 80000 {
>> +                label = "ospi.tispl";
>> +                reg = <0x80000 0x200000>;
>> +            };
>> +
>> +            partition at 280000 {
>> +                label = "ospi.u-boot";
>> +                reg = <0x280000 0x400000>;
>> +            };
>> +
>> +            partition at 680000 {
>> +                label = "ospi.env";
>> +                reg = <0x680000 0x40000>;
>> +            };
>> +
>> +            partition at 6c0000 {
>> +                label = "ospi.env.backup";
>> +                reg = <0x6c0000 0x40000>;
>> +            };
>> +
>> +            partition at 800000 {
>> +                label = "ospi.rootfs";
>> +                reg = <0x800000 0x37c0000>;
>> +            };
>> +
>> +            partition at 3fc0000 {
>> +                label = "ospi.phypattern";
>> +                reg = <0x3fc0000 0x40000>;
>> +            };
>> +        };
>> +    };
>> +
>> +};
>> +
>>   &sdhci1 {
>>       /* SD/MMC */
>>       vmmc-supply = <&vdd_mmc1>;