[PATCH v2] arm64: dts: ti: am62-phyboard-lyra: Add overlay to enable a GPIO fan

[Wadim Egorov]

Hi Nathan,

Am 09.02.24 um 01:29 schrieb Nathan Morrisson:
> The phyBOARD-Lyra has a GPIO fan header. This overlay enables the fan
> header and sets the fan to turn on at 65C.
>
> Signed-off-by: Nathan Morrisson <nmorrisson at phytec.com>
> ---
> v2:
> - Change overlay name from k3-am62-... to k3-am62x-...
> - Add compile time test
>
>   arch/arm64/boot/dts/ti/Makefile               |  3 ++
>   .../ti/k3-am62x-phyboard-lyra-gpio-fan.dtso   | 51 +++++++++++++++++++
>   2 files changed, 54 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra-gpio-fan.dtso
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 52c1dc910308..bfeb496d5039 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dahlia.dtb
>   dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dev.dtb
>   dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-mallow.dtb
>   dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-yavia.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am62x-phyboard-lyra-gpio-fan.dtbo
>   dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk.dtb
>   
>   # Boards with AM62Ax SoC
> @@ -87,6 +88,8 @@ k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
>   	k3-am625-beagleplay-csi2-ov5640.dtbo
>   k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
>   	k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
> +k3-am625-phyboard-lyra-gpio-fan-dtbs := k3-am625-phyboard-lyra-rdk.dtb \
> +	k3-am62x-phyboard-lyra-gpio-fan.dtbo
>   k3-am625-sk-csi2-imx219-dtbs := k3-am625-sk.dtb \
>   	k3-am62x-sk-csi2-imx219.dtbo
>   k3-am625-sk-csi2-ov5640-dtbs := k3-am625-sk.dtb \
> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra-gpio-fan.dtso b/arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra-gpio-fan.dtso
> new file mode 100644
> index 000000000000..9c05748bdd9d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra-gpio-fan.dtso
> @@ -0,0 +1,51 @@
> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> +/*
> + * Copyright (C) 2024 PHYTEC America LLC
> + * Author: Garrett Giordano <ggiordano at phytec.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/thermal/thermal.h>
> +#include "k3-pinctrl.h"
> +
> +&{/} {
> +	fan: gpio-fan {
> +		compatible = "gpio-fan";
> +		gpio-fan,speed-map = <0 0 8600 1>;
> +		gpios = <&main_gpio0 40 GPIO_ACTIVE_LOW>;
> +		#cooling-cells = <2>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&gpio_fan_pins_default>;
> +		status = "okay";

There is no need to set the status. If no status is present, it also 
indicates that the node is activated.

With this change,

Reviewed-by: Wadim Egorov <w.egorov at phytec.de>


> +	};
> +};
> +
> +&main_pmx0 {
> +	gpio_fan_pins_default: gpio-fan-default-pins {
> +		pinctrl-single,pins = <
> +			AM62X_IOPAD(0x0a4, PIN_OUTPUT, 7) /* (M22) GPMC0_DIR.GPIO0_40 */
> +		>;
> +	};
> +};
> +
> +&thermal_zones {
> +	main0_thermal: main0-thermal {
> +		trips {
> +			main0_thermal_trip0: main0-thermal-trip {
> +				temperature = <65000>;  /* millicelsius */
> +				hysteresis = <2000>;    /* millicelsius */
> +				type = "active";
> +			};
> +		};
> +
> +		cooling-maps {
> +			map0 {
> +				trip = <&main0_thermal_trip0>;
> +				cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};
> +		};
> +	};
> +};