[PATCH] arm64: dts: ti: am62-phyboard-lyra: Add overlay to enable a GPIO fan

[Wadim Egorov]

Hi Andrew,

Am 07.02.24 um 23:20 schrieb Andrew Davis:
> On 2/7/24 11:28 AM, Nathan Morrisson wrote:
>> The phyBOARD-Lyra has a GPIO fan header. This overlay enables the fan
>> header and sets the fan to turn on at 65C.
>>
>> Signed-off-by: Nathan Morrisson <nmorrisson at phytec.com>
>> ---
>>   arch/arm64/boot/dts/ti/Makefile               |  1 +
>>   .../ti/k3-am62-phyboard-lyra-gpio-fan.dtso    | 51 +++++++++++++++++++
>>   2 files changed, 52 insertions(+)
>>   create mode 100644 
>> arch/arm64/boot/dts/ti/k3-am62-phyboard-lyra-gpio-fan.dtso
>>
>> diff --git a/arch/arm64/boot/dts/ti/Makefile 
>> b/arch/arm64/boot/dts/ti/Makefile
>> index 52c1dc910308..379fb4f31a1f 100644
>> --- a/arch/arm64/boot/dts/ti/Makefile
>> +++ b/arch/arm64/boot/dts/ti/Makefile
>> @@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dev.dtb
>>   dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-mallow.dtb
>>   dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-yavia.dtb
>>   dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk.dtb
>> +dtb-$(CONFIG_ARCH_K3) += k3-am62-phyboard-lyra-gpio-fan.dtbo
>
> Why not call this k3-am625-phyboard-lyra-gpio-fan.dtbo to match the
> name of the base board it applies to better?

We are able to reuse this overlay for different SoMs (am625 and am62a) 
that are using the same carrier board (lyra).

Regards,
Wadim


>
> Andrew
>
>>     # Boards with AM62Ax SoC
>>   dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb
>> diff --git 
>> a/arch/arm64/boot/dts/ti/k3-am62-phyboard-lyra-gpio-fan.dtso 
>> b/arch/arm64/boot/dts/ti/k3-am62-phyboard-lyra-gpio-fan.dtso
>> new file mode 100644
>> index 000000000000..9c05748bdd9d
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/ti/k3-am62-phyboard-lyra-gpio-fan.dtso
>> @@ -0,0 +1,51 @@
>> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
>> +/*
>> + * Copyright (C) 2024 PHYTEC America LLC
>> + * Author: Garrett Giordano <ggiordano at phytec.com>
>> + */
>> +
>> +/dts-v1/;
>> +/plugin/;
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/thermal/thermal.h>
>> +#include "k3-pinctrl.h"
>> +
>> +&{/} {
>> +    fan: gpio-fan {
>> +        compatible = "gpio-fan";
>> +        gpio-fan,speed-map = <0 0 8600 1>;
>> +        gpios = <&main_gpio0 40 GPIO_ACTIVE_LOW>;
>> +        #cooling-cells = <2>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&gpio_fan_pins_default>;
>> +        status = "okay";
>> +    };
>> +};
>> +
>> +&main_pmx0 {
>> +    gpio_fan_pins_default: gpio-fan-default-pins {
>> +        pinctrl-single,pins = <
>> +            AM62X_IOPAD(0x0a4, PIN_OUTPUT, 7) /* (M22) 
>> GPMC0_DIR.GPIO0_40 */
>> +        >;
>> +    };
>> +};
>> +
>> +&thermal_zones {
>> +    main0_thermal: main0-thermal {
>> +        trips {
>> +            main0_thermal_trip0: main0-thermal-trip {
>> +                temperature = <65000>;  /* millicelsius */
>> +                hysteresis = <2000>;    /* millicelsius */
>> +                type = "active";
>> +            };
>> +        };
>> +
>> +        cooling-maps {
>> +            map0 {
>> +                trip = <&main0_thermal_trip0>;
>> +                cooling-device = <&fan THERMAL_NO_LIMIT 
>> THERMAL_NO_LIMIT>;
>> +            };
>> +        };
>> +    };
>> +};
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel