[PATCH] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash

[Sinthu Raja]

From: Sinthu Raja <sinthu.raja at ti.com>

AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.

Signed-off-by: Sinthu Raja <sinthu.raja at ti.com>
---
 arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 79 ++++++++++++++++++++++
 1 file changed, 79 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
index 20861a0a46b0..84011d5e1b3b 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
@@ -130,6 +130,25 @@ rtos_ipc_memory_region: ipc-memories at a8000000 {
 	};
 };
 
+&wkup_pmx0 {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+			J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+			J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+			J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
+		>;
+	};
+};
+
 &wkup_pmx2 {
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
 		pinctrl-single,pins = <
@@ -152,6 +171,66 @@ eeprom at 51 {
 	};
 };
 
+&ospi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "ospi.tiboot3";
+				reg = <0x0 0x80000>;
+			};
+
+			partition at 80000 {
+				label = "ospi.tispl";
+				reg = <0x80000 0x200000>;
+			};
+
+			partition at 280000 {
+				label = "ospi.u-boot";
+				reg = <0x280000 0x400000>;
+			};
+
+			partition at 680000 {
+				label = "ospi.env";
+				reg = <0x680000 0x40000>;
+			};
+
+			partition at 6c0000 {
+				label = "ospi.env.backup";
+				reg = <0x6c0000 0x40000>;
+			};
+
+			partition at 800000 {
+				label = "ospi.rootfs";
+				reg = <0x800000 0x37c0000>;
+			};
+
+			partition at 3fc0000 {
+				label = "ospi.phypattern";
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+	};
+};
+
 &mailbox0_cluster0 {
 	status = "okay";
 	interrupts = <436>;
-- 
2.36.1